Visible to Intel only — GUID: sss1440053679142
Ixiasoft
1. Intel® Agilex™ Configuration User Guide
2. Intel® Agilex™ Configuration Details
3. Intel® Agilex™ Configuration Schemes
4. Including the Reset Release Intel® FPGA IP in Your Design
5. Remote System Update (RSU)
6. Intel® Agilex™ Configuration Features
7. Intel® Agilex™ Debugging Guide
8. Intel® Agilex™ Configuration User Guide Archives
9. Document Revision History for the Intel® Agilex™ Configuration User Guide
2.1. Intel® Agilex™ Configuration Timing Diagram
2.2. Configuration Flow Diagram
2.3. Device Response to Configuration and Reset Events
2.4. Additional Clock Requirements for HPS and Transceivers
2.5. Intel® Agilex™ Configuration Pins
2.6. Configuration Clocks
2.7. Intel® Agilex™ Configuration Time Estimation
2.8. Generating Compressed .sof File
3.1.1. Avalon® -ST Configuration Scheme Hardware Components and File Types
3.1.2. Enabling Avalon-ST Device Configuration
3.1.3. The AVST_READY Signal
3.1.4. RBF Configuration File Format
3.1.5. Avalon-ST Single-Device Configuration
3.1.6. Debugging Guidelines for the Avalon® -ST Configuration Scheme
3.1.7. IP for Use with the Avalon® -ST Configuration Scheme: Intel FPGA Parallel Flash Loader II IP Core
3.1.7.4.1. PFL II IP Recommended Design Constraints to FPGA Avalon-ST Pins
3.1.7.4.2. PFL II IP Recommended Design Constraints for Using QSPI Flash
3.1.7.4.3. PFL II IP Recommended Design Constraints for using CFI Flash
3.1.7.4.4. PFL II IP Recommended Constraints for Other Input Pins
3.1.7.4.5. PFL II IP Recommended Constraints for Other Output Pins
3.2.1. AS Configuration Scheme Hardware Components and File Types
3.2.2. AS Single-Device Configuration
3.2.3. AS Using Multiple Serial Flash Devices
3.2.4. AS Configuration Timing Parameters
3.2.5. Maximum Allowable External AS_DATA Pin Skew Delay Guidelines
3.2.6. Programming Serial Flash Devices
3.2.7. Serial Flash Memory Layout
3.2.8. AS_CLK
3.2.9. Active Serial Configuration Software Settings
3.2.10. Intel® Quartus® Prime Programming Steps
3.2.11. Debugging Guidelines for the AS Configuration Scheme
5.1. Remote System Update Functional Description
5.2. Guidelines for Performing Remote System Update Functions for Non-HPS
5.3. Commands and Responses
5.4. Quad SPI Flash Layout
5.5. Generating Remote System Update Image Files Using the Programming File Generator
5.6. Remote System Update from FPGA Core Example
5.6.1. Prerequisites
5.6.2. Creating Initial Flash Image Containing Bitstreams for Factory Image and One Application Image
5.6.3. Programming Flash Memory with the Initial Remote System Update Image
5.6.4. Reconfiguring the Device with an Application or Factory Image
5.6.5. Adding an Application Image
5.6.6. Removing an Application Image
7.1. Configuration Debugging Checklist
7.2. Intel® Agilex™ Configuration Architecture Overview
7.3. Understanding Configuration Status Using quartus_pgm command
7.4. Configuration File Format Differences
7.5. Understanding SEUs
7.6. Reading the Unique 64-Bit CHIP ID
7.7. E-Tile Transceivers May Fail To Configure
7.8. Understanding and Troubleshooting Configuration Pin Behavior
Visible to Intel only — GUID: sss1440053679142
Ixiasoft
3.2.6.2. Programming Serial Flash Devices using the JTAG Interface
The Intel® Quartus® Prime Programmer interfaces to the SDM device through JTAG interface and programs the serial flash device.
Figure 43. Programming Your Serial Configuration Device Using JTAG
Figure 44. Connections for Programming the Serial Flash Devices using the JTAG Interface
Intel recommends using the JTAG interface to prepare the Quad SPI flash device for later use in AS mode.
This configuration scheme includes the following steps:
- In the Intel® Quartus® Prime Programmer, select the JTAG programming mode and initiate programming by clicking Start.
- The Programmer drives .jic configuration data to the board using the JTAG header connection.
- The programmer first configures the SDM with configuration firmware. Then, the SDM drives configuration data from the programmer to the AS x4 flash device using SDM_IOs.
- If your current MSEL pins are not set to AS fast or normal mode in order to configure the Intel® Agilex™ device in AS mode after successful programming of the flash device, set the MSEL pins to either AS fast or AS normal mode and power cycle the device.
The Intel® Quartus® Prime Programmer interfaces to the SDM device through JTAG interface and programs the serial flash device.