Visible to Intel only — GUID: wlb1615942964227
Ixiasoft
1. Intel® Agilex™ Configuration User Guide
2. Intel® Agilex™ Configuration Details
3. Intel® Agilex™ Configuration Schemes
4. Including the Reset Release Intel® FPGA IP in Your Design
5. Remote System Update (RSU)
6. Intel® Agilex™ Configuration Features
7. Intel® Agilex™ Debugging Guide
8. Intel® Agilex™ Configuration User Guide Archives
9. Document Revision History for the Intel® Agilex™ Configuration User Guide
2.1. Intel® Agilex™ Configuration Timing Diagram
2.2. Configuration Flow Diagram
2.3. Device Response to Configuration and Reset Events
2.4. Additional Clock Requirements for HPS and Transceivers
2.5. Intel® Agilex™ Configuration Pins
2.6. Configuration Clocks
2.7. Intel® Agilex™ Configuration Time Estimation
2.8. Generating Compressed .sof File
3.1.1. Avalon® -ST Configuration Scheme Hardware Components and File Types
3.1.2. Enabling Avalon-ST Device Configuration
3.1.3. The AVST_READY Signal
3.1.4. RBF Configuration File Format
3.1.5. Avalon-ST Single-Device Configuration
3.1.6. Debugging Guidelines for the Avalon® -ST Configuration Scheme
3.1.7. IP for Use with the Avalon® -ST Configuration Scheme: Intel FPGA Parallel Flash Loader II IP Core
3.1.7.4.1. PFL II IP Recommended Design Constraints to FPGA Avalon-ST Pins
3.1.7.4.2. PFL II IP Recommended Design Constraints for Using QSPI Flash
Create a FLASH_CLK clock
Set output delay for PFL II IP output pins
Set input delay for input pins
3.1.7.4.3. PFL II IP Recommended Design Constraints for using CFI Flash
3.1.7.4.4. PFL II IP Recommended Constraints for Other Input Pins
3.1.7.4.5. PFL II IP Recommended Constraints for Other Output Pins
3.2.1. AS Configuration Scheme Hardware Components and File Types
3.2.2. AS Single-Device Configuration
3.2.3. AS Using Multiple Serial Flash Devices
3.2.4. AS Configuration Timing Parameters
3.2.5. Maximum Allowable External AS_DATA Pin Skew Delay Guidelines
3.2.6. Programming Serial Flash Devices
3.2.7. Serial Flash Memory Layout
3.2.8. AS_CLK
3.2.9. Active Serial Configuration Software Settings
3.2.10. Intel® Quartus® Prime Programming Steps
3.2.11. Debugging Guidelines for the AS Configuration Scheme
5.1. Remote System Update Functional Description
5.2. Guidelines for Performing Remote System Update Functions for Non-HPS
5.3. Commands and Responses
5.4. Quad SPI Flash Layout
5.5. Generating Remote System Update Image Files Using the Programming File Generator
5.6. Remote System Update from FPGA Core Example
5.6.1. Prerequisites
5.6.2. Creating Initial Flash Image Containing Bitstreams for Factory Image and One Application Image
5.6.3. Programming Flash Memory with the Initial Remote System Update Image
5.6.4. Reconfiguring the Device with an Application or Factory Image
5.6.5. Adding an Application Image
5.6.6. Removing an Application Image
7.1. Configuration Debugging Checklist
7.2. Intel® Agilex™ Configuration Architecture Overview
7.3. Understanding Configuration Status Using quartus_pgm command
7.4. Configuration File Format Differences
7.5. Understanding SEUs
7.6. Reading the Unique 64-Bit CHIP ID
7.7. E-Tile Transceivers May Fail To Configure
7.8. Understanding and Troubleshooting Configuration Pin Behavior
Visible to Intel only — GUID: wlb1615942964227
Ixiasoft
3.1.7.4.2. PFL II IP Recommended Design Constraints for Using QSPI Flash
Create a FLASH_CLK clock
Example below creates assigns QSPI flash clock pin (flash_dc1_ic0) to the flash clock.
create_generated_clock -name FLASH_CLK -source [get_ports {clk_50m_sysmax}] [get_ports {flash_dc1_io0}]
Set output delay for PFL II IP output pins
Example below sets the output delay for the QSPI flash data and chip select pins.
#flash_dc1_io1/3/4/5 = QSPI flash data pins,
#flash_dc1_io2 = QSPI flash chip select pins
set flash_data_tracemax 0.250
set flash_data_tracemin 0.000
set flash_clk_tracemax 0.250
set flash_clk_tracemin 0.000
set flash_Tsu 2.700
set flash_Th 2.000
set flash_out_max_dly [expr $flash_data_tracemax + $flash_Tsu - $flash_clk_tracemin]
set flash_out_min_dly [expr $flash_data_tracemin - $flash_Th - $flash_clk_tracemax]
set_output_delay -add_delay -max \
-clock [get_clocks {FLASH_CLK}] $flash_out_max_dly [get_ports {flash_dc1_io1 flash_dc1_io3 flash_dc1_io4 flash_dc1_io5 flash_dc1_io2}]
set_output_delay -add_delay -min \
-clock [get_clocks {FLASH_CLK}] $flash_out_min_dly [get_ports { flash_dc1_io1 flash_dc1_io3 flash_dc1_io4 flash_dc1_io5 flash_dc1_io2}]
Set input delay for input pins
Example below sets the input delay for the QSPI flash data.
set flash_tco_max 7.000
set flash_tco_min 1.000
set in_max_dly [expr $flash_data_tracemax + $flash_tco_max + $flash_clk_tracemax]
set in_min_dly [expr $flash_data_tracemin + $flash_tco_min + $flash_clk_tracemin]
set_input_delay -clock { FLASH_CLK } -max $in_max_dly [get_ports {flash_dc1_io1 flash_dc1_io3 flash_dc1_io4 flash_dc1_io5}]
set_input_delay -clock { FLASH_CLK } -min $in_min_dly [get_ports {flash_dc1_io1 flash_dc1_io3 flash_dc1_io4 flash_dc1_io5}]