Low Latency E-Tile 40G Ethernet Intel® FPGA IP User Guide

Download PDF
ID 683486
Date 7/12/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the Low Latency E-Tile 40G Ethernet Intel® FPGA IP 2. Low Latency E-Tile 40G Ethernet IP Core Parameters 3. Getting Started 4. Functional Description 5. Reset 6. Interfaces and Signal Descriptions 7. Control, Status, and Statistics Register Descriptions 8. Debugging the Link 9. Ethernet Toolkit Overview 10. Low Latency E-Tile 40G Ethernet Intel® FPGA IP User Guide Archives 11. Comparison Between Low Latency E-Tile 40G Ethernet Core and Low Latency 40GbE IP Core 12. Document Revision History for Low Latency E-Tile 40G Ethernet Intel® FPGA IP User Guide
1. About the Low Latency E-Tile 40G Ethernet Intel® FPGA IP x
1.1. Release Information 1.2. Low Latency E-Tile 40G Ethernet Intel® FPGA IP Supported Features 1.3. Low Latency E-Tile 40G Ethernet Intel® FPGA IP Device Family and Speed Grade Support 1.4. Resource Utilization
1.3. Low Latency E-Tile 40G Ethernet Intel® FPGA IP Device Family and Speed Grade Support x
1.3.1. Device Family Support 1.3.2. Low Latency E-Tile 40G Ethernet Intel® FPGA IP Device Speed Grade Support
3. Getting Started x
3.1. Installing and Licensing Intel® FPGA IP Cores 3.2. Specifying the Low Latency E-Tile 40G Ethernet IP Core Parameters and Options 3.3. Simulating the IP Core 3.4. Generated File Structure 3.5. Integrating Your IP Core in Your Design 3.6. Low Latency E-Tile 40G Ethernet IP Core Testbench 3.7. Compiling the Full Design and Programming the FPGA
3.5. Integrating Your IP Core in Your Design x
3.5.1. Pin Assignments 3.5.2. Ethernet Adaptation Flow 3.5.3. Placement Settings for the Low Latency E-Tile 40G Ethernet Core
3.6. Low Latency E-Tile 40G Ethernet IP Core Testbench x
3.6.1. Understanding the Testbench Behavior
4. Functional Description x
4.1. Low Latency E-Tile 40G Ethernet Core Functional Description 4.2. User Interface to Ethernet Transmission
4.1. Low Latency E-Tile 40G Ethernet Core Functional Description x
4.1.1. Low Latency E-Tile 40G Ethernet Core TX MAC Datapath 4.1.2. Low Latency E-Tile 40G Ethernet Core RX MAC Datapath 4.1.3. Link Fault Signaling Interface 4.1.4. Flow Control
4.1.1. Low Latency E-Tile 40G Ethernet Core TX MAC Datapath x
4.1.1.1. Frame Padding 4.1.1.2. Preamble Insertion 4.1.1.3. Inter-Packet Gap Generation and Insertion 4.1.1.4. Frame Check Sequence (CRC-32) Insertion
4.1.2. Low Latency E-Tile 40G Ethernet Core RX MAC Datapath x
4.1.2.1. IP Core Preamble Processing 4.1.2.2. IP Core Strict SFD Checking 4.1.2.3. Length/Type Field Processing 4.1.2.4. RX CRC Checking and Dynamic Forwarding
4.1.2.3. Length/Type Field Processing x
4.1.2.3.1. Length Checking
4.1.4. Flow Control x
4.1.4.1. TX Pause/PFC Flow Control Transmission 4.1.4.2. XON/XOFF Pause Frames
4.2. User Interface to Ethernet Transmission x
4.2.1. Order of Transmission 4.2.2. Bit Order For TX and RX Datapaths
6. Interfaces and Signal Descriptions x
6.1. TX MAC Interface to User Logic 6.2. RX MAC Interface to User Logic 6.3. Transceivers Signals 6.4. Transceiver Reconfiguration Signals 6.5. Avalon® Memory-Mapped Management Interface 6.6. Miscellaneous Status and Debug Signals 6.7. Reset Signals 6.8. Clocks 6.9. Flow Control Interface
7. Control, Status, and Statistics Register Descriptions x
7.1. PHY Registers 7.2. TX MAC Registers 7.3. RX MAC Registers 7.4. Pause/PFC Flow Control Registers
9. Ethernet Toolkit Overview x
9.1. Features
1. About the Low Latency E-Tile 40G Ethernet Intel® FPGA IP
2. Low Latency E-Tile 40G Ethernet IP Core Parameters
3. Getting Started
4. Functional Description
5. Reset
6. Interfaces and Signal Descriptions
7. Control, Status, and Statistics Register Descriptions
8. Debugging the Link
9. Ethernet Toolkit Overview
10. Low Latency E-Tile 40G Ethernet Intel® FPGA IP User Guide Archives
11. Comparison Between Low Latency E-Tile 40G Ethernet Core and Low Latency 40GbE IP Core
12. Document Revision History for Low Latency E-Tile 40G Ethernet Intel® FPGA IP User Guide

3.5.2. Ethernet Adaptation Flow

Refer to Loading a PMA Configuration and PMA Registers 0x200 to 0x203 Usage sections in the E-tile Transceiver PHY User Guide for more details on the adaptation flow and how to get started.

This adaptation flow assumes a valid Ethernet traffic.

  1. Assert tx_rst_n and rx_rst_n signals.
  2. Trigger PMA analog.
  3. Reload PMA settings and call PMA attribute sequencer on all lanes.
  4. Apply control status registers (CSR) reset.
  5. Deassert the tx_rst_n signal.
  6. If using a PMA configuration, load the PMA configuration using control status registers (CSR). This is loaded to the registers using PMA registers 0x200 to 0x203 1.
    1. Write 0x40143 = 0x80.
    2. Read 0x40144[0] until it changes to 1.
  7. Enable internal serial loopback 2 and run initial adaptation. Verify that the initial adaptation status is complete using interrupt code 0x0126 and data 0x0B00.
  8. Enable mission mode and disable internal serial loopback (skip this step if using internal serial loopback)2.
  9. Wait for valid data traffic on RX and then proceed to the next step.
  10. Run initial adaptation. Verify that the initial adaptation status is complete using interrupt code 0x0126 and data 0x0B00 (skip this step if using internal serial loopback).
  11. Run continuous adaptation 3.
  12. Deassert the rx_rst_n signal.
  13. Optional: Verify that the link status signal rx_aligned transitions high.
  14. Send packets.
1 Refer to Loading a PMA Configuration and PMA Registers 0x200 to 0x203 Usage.
2 For how to enable and disable internal serial loopback, refer to 0x0008: Internal Serial Loopback and Reverse Parallel Loopback Control.
3 During the continuous adaptation, the link partner must keep sending the data. If link goes down, the entire sequence must be repeated.
Level Two Title