Visible to Intel only — GUID: jrz1522207840091
Ixiasoft
1. Intel® Stratix® 10 Embedded Memory Overview
2. Intel® Stratix® 10 Embedded Memory Architecture and Features
3. Intel® Stratix® 10 Embedded Memory Design Considerations
4. Intel® Stratix® 10 Embedded Memory IP References
5. Intel Stratix 10 Embedded Memory Design Example
6. Intel® Stratix® 10 Embedded Memory User Guide Archives
7. Document Revision History for the Intel® Stratix® 10 Embedded Memory User Guide
2.1. Byte Enable in Intel® Stratix® 10 Embedded Memory Blocks
2.2. Address Clock Enable Support
2.3. Asynchronous Clear and Synchronous Clear
2.4. Memory Blocks Error Correction Code Support
2.5. Force-to-Zero
2.6. Coherent Read Memory
2.7. Freeze Logic
2.8. True Dual Port Dual Clock Emulator
2.9. 'X' Propagation Support in Simulation
2.10. Intel® Stratix® 10 Supported Embedded Memory IPs
2.11. Intel® Stratix® 10 Embedded Memory Clocking Modes
2.12. Intel® Stratix® 10 Embedded Memory Configurations
2.13. Initial Value of Read and Write Address Registers
3.1. Consider the Memory Block Selection
3.2. Consider the Concurrent Read Behavior
3.3. Customize Read-During-Write Behavior
3.4. Consider Power-Up State and Memory Initialization
3.5. Reduce Power Consumption
3.6. Avoid Providing Non-Deterministic Input
3.7. Avoid Changing Clock Signals and Other Control Signals Simultaneously
3.8. Including the Reset Release Intel® FPGA IP in Your Design
4.1.1. Release Information for RAM and ROM Intel® FPGA IPs
4.1.2. RAM: 1-PORT Intel® FPGA IP Parameters
4.1.3. RAM: 2-PORT Intel® FPGA IP Parameters
4.1.4. RAM: 4-PORT Intel® FPGA IP Parameters
4.1.5. ROM: 1-PORT Intel® FPGA IP Parameters
4.1.6. ROM: 2-PORT Intel® FPGA IP Parameters
4.1.7. RAM and ROM Interface Signals
4.1.8. Changing Parameter Settings Manually
4.3.1. Release Information for FIFO Intel® FPGA IP
4.3.2. Configuration Methods
4.3.3. Specifications
4.3.4. FIFO Functional Timing Requirements
4.3.5. SCFIFO ALMOST_EMPTY Functional Timing
4.3.6. FIFO Output Status Flag and Latency
4.3.7. FIFO Metastability Protection and Related Options
4.3.8. FIFO Synchronous Clear and Asynchronous Clear Effect
4.3.9. SCFIFO and DCFIFO Show-Ahead Mode
4.3.10. Different Input and Output Width
4.3.11. DCFIFO Timing Constraint Setting
4.3.12. Coding Example for Manual Instantiation
4.3.13. Design Example
4.3.14. Gray-Code Counter Transfer at the Clock Domain Crossing
4.3.15. Guidelines for Embedded Memory ECC Feature
4.3.16. FIFO Intel® FPGA IP Parameters
4.3.17. Reset Scheme
4.4.1. Release Information for FIFO2 Intel® FPGA IP
4.4.2. Configuration Methods
4.4.3. Fmax Target Measuring Methodology
4.4.4. Performance Considerations
4.4.5. FIFO2 Intel® FPGA IP Features
4.4.6. FIFO2 Intel® FPGA IP Parameters
4.4.7. FIFO2 Intel® FPGA IP Interface Signals
4.4.8. Reset and Clock Schemes
4.5.1. Release Information for Shift Register (RAM-based) Intel® FPGA IP
4.5.2. Shift Register (RAM-based) Intel® FPGA IP Features
4.5.3. Shift Register (RAM-based) Intel® FPGA IP General Description
4.5.4. Shift Register (RAM-based) Intel® FPGA IP Parameter Settings
4.5.5. Shift Register Ports and Parameters Setting
Visible to Intel only — GUID: jrz1522207840091
Ixiasoft
2.6. Coherent Read Memory
The coherent read memory feature allows you to read out the output data that will be written into the same memory content in a single clock cycle. In other words, you will experience the new data (flow through) behavior during the read-during-write operation. This feature is applicable only for M20K blocks and supported only in single clock configuration.
If you engage the coherent read memory feature, you cannot use the following configurations:
- Operating modes other than simple dual-port
- Simple dual-port with different port width
- Byte enable
- ECC
- Wide simple dual-port
- Dual clock configuration
Figure 8. Simplified Block Diagram of Coherent Read Memory Circuitry
Figure 9. Coherent Read Memory Behavior for Unregistered OutputThis figure shows the waveform of the coherent read memory when the output is unregistered.
Figure 10. Coherent Read Memory Behavior for Registered OutputThis figure shows the waveform of the coherent read memory when the output is registered.