Low Latency 100-Gbps Ethernet IP Core User Guide

Download PDF
ID 683160
Date 4/15/2021
Public
Document Table of Contents
Document Table of Contents x
1. About the LL 100GbE IP Core 2. Getting Started 3. Functional Description 4. Debugging the Link A. Additional Information
1. About the LL 100GbE IP Core x
1.1. LL 100GbE IP Core Supported Features 1.2. IP Core Device Family and Speed Grade Support 1.3. IP Core Verification 1.4. Performance and Resource Utilization 1.5. Release Information
1.2. IP Core Device Family and Speed Grade Support x
1.2.1. LL 100GbE IP Core Device Family Support 1.2.2. LL 100GbE IP Core Device Speed Grade Support
1.3. IP Core Verification x
1.3.1. Simulation Environment 1.3.2. Compilation Checking 1.3.3. Hardware Testing
1.4. Performance and Resource Utilization x
1.4.1. Arria 10 Resource Utilization 1.4.2. Stratix V Resource Utilization
2. Getting Started x
2.1. Installation and Licensing for LL 100GbE IP Core for Stratix® V Devices 2.2. Installing and Licensing Intel® FPGA IP Cores 2.3. Specifying the IP Core Parameters and Options 2.4. IP Core Parameters 2.5. Files Generated for Stratix V Variations 2.6. Files Generated for Arria 10 Variations 2.7. Integrating Your IP Core in Your Design 2.8. IP Core Testbenches 2.9. Compiling the Full Design and Programming the FPGA 2.10. Initializing the IP Core
2.2. Installing and Licensing Intel® FPGA IP Cores x
2.2.1. Intel® FPGA IP Evaluation Mode
2.7. Integrating Your IP Core in Your Design x
2.7.1. Pin Assignments 2.7.2. External Transceiver Reconfiguration Controller Required in Stratix V Designs 2.7.3. Transceiver PLL Required in Arria 10 Designs 2.7.4. Handling Potential Jitter in Intel® Arria® 10 Devices 2.7.5. External Time-of-Day Module for Variations with 1588 PTP Feature 2.7.6. External TX MAC PLL 2.7.7. Placement Settings for the LL 100GbE Core
2.8. IP Core Testbenches x
2.8.1. Testbench Behavior 2.8.2. Simulating the LL 100GbE IP Core With the Testbenches
2.8.2. Simulating the LL 100GbE IP Core With the Testbenches x
2.8.2.1. Generating the LL 100GbE Testbench 2.8.2.2. Optimizing the IP Core Simulation With the Testbenches 2.8.2.3. Simulating with the Modelsim Simulator 2.8.2.4. Simulating with the NCSim Simulator 2.8.2.5. Simulating with the VCS Simulator 2.8.2.6. Testbench Output Example
3. Functional Description x
3.1. High Level System Overview 3.2. LL 100GbE IP Core Functional Description 3.3. Signals 3.4. Software Interface: Registers 3.5. Ethernet Glossary
3.2. LL 100GbE IP Core Functional Description x
3.2.1. LL 100GbE IP Core TX Datapath 3.2.2. LL 100GbE IP Core TX Data Bus Interfaces 3.2.3. LL 100GbE IP Core RX Datapath 3.2.4. LL 100GbE IP Core RX Data Bus Interfaces 3.2.5. Low Latency 100GbE CAUI–4 PHY 3.2.6. External Reconfiguration Controller 3.2.7. External Transceiver PLL 3.2.8. External TX MAC PLL 3.2.9. Congestion and Flow Control Using Pause Frames 3.2.10. Pause Control and Generation Interface 3.2.11. Pause Control Frame Filtering 3.2.12. Link Fault Signaling Interface 3.2.13. Statistics Counters Interface 3.2.14. 1588 Precision Time Protocol Interfaces 3.2.15. PHY Status Interface 3.2.16. Transceiver PHY Serial Data Interface 3.2.17. Control and Status Interface 3.2.18. Arria 10 Transceiver Reconfiguration Interface 3.2.19. Clocks 3.2.20. Resets
3.2.1. LL 100GbE IP Core TX Datapath x
3.2.1.1. Preamble, Start, and SFD Insertion 3.2.1.2. Address Insertion 3.2.1.3. Length/Type Field Processing 3.2.1.4. Frame Padding 3.2.1.5. Frame Check Sequence (CRC-32) Insertion 3.2.1.6. Inter-Packet Gap Generation and Insertion 3.2.1.7. TX RSFEC 3.2.1.8. Error Insertion Test and Debug Feature
3.2.2. LL 100GbE IP Core TX Data Bus Interfaces x
3.2.2.1. LL 100GbE IP Core User Interface Data Bus 3.2.2.2. LL 100GbE IP Core TX Data Bus with Adapters (Avalon-ST Interface) 3.2.2.3. LL 100GbE IP Core TX Data Bus Without Adapters (Custom Streaming Interface) 3.2.2.4. Bus Quantization Effects With Adapters 3.2.2.5. User Interface to Ethernet Transmission
3.2.2.5. User Interface to Ethernet Transmission x
3.2.2.5.1. Order of Transmission
3.2.3. LL 100GbE IP Core RX Datapath x
3.2.3.1. LL 100GbE IP Core RX Filtering 3.2.3.2. LL 100GbE IP Core Preamble Processing 3.2.3.3. LL 100GbE IP Core FCS (CRC-32) Removal 3.2.3.4. LL 100GbE IP Core CRC Checking 3.2.3.5. LL 100GbE IP Core Malformed Packet Handling 3.2.3.6. RX CRC Forwarding 3.2.3.7. Inter-Packet Gap 3.2.3.8. RX RSFEC 3.2.3.9. Pause Ignore 3.2.3.10. Control Frame Identification
3.2.4. LL 100GbE IP Core RX Data Bus Interfaces x
3.2.4.1. LL 100GbE IP Core User Interface Data Bus 3.2.4.2. LL 100GbE IP Core RX Data Bus with Adapters (Avalon-ST Interface) 3.2.4.3. LL 100GbE IP Core RX Data Bus Without Adapters (Custom Streaming Interface)
3.2.9. Congestion and Flow Control Using Pause Frames x
3.2.9.1. Conditions Triggering XOFF Frame Transmission 3.2.9.2. Conditions Triggering XON Frame Transmission
3.2.13. Statistics Counters Interface x
3.2.13.1. OctetOK Count Interface
3.2.14. 1588 Precision Time Protocol Interfaces x
3.2.14.1. Implementing a 1588 System That Includes a LL 100GbE Core 3.2.14.2. PTP Receive Functionality 3.2.14.3. PTP Transmit Functionality 3.2.14.4. External Time-of-Day Module for 1588 PTP Variations 3.2.14.5. PTP Timestamp and TOD Formats 3.2.14.6. 1588 PTP Interface Signals
3.3. Signals x
3.3.1. LL 100GbE IP Core Signals
3.4. Software Interface: Registers x
3.4.1. LL 100GbE IP Core Registers 3.4.2. LL 100GbE Hardware Design Example Registers
3.4.1. LL 100GbE IP Core Registers x
3.4.1.1. PHY Registers 3.4.1.2. Link Fault Signaling Registers 3.4.1.3. LL 100GbE IP Core MAC Configuration Registers 3.4.1.4. Pause Registers 3.4.1.5. TX Statistics Registers 3.4.1.6. RX Statistics Registers 3.4.1.7. 1588 PTP Registers 3.4.1.8. TX Reed-Solomon FEC Registers 3.4.1.9. RX Reed-Solomon FEC Registers
3.4.2. LL 100GbE Hardware Design Example Registers x
3.4.2.1. Packet Client Registers
4. Debugging the Link x
4.1. Creating a Signal Tap Debug File to Match Your Design Hierarchy
A. Additional Information x
A.1. LL 100GbE IP Core User Guide Archives A.2. LL 100GbE IP Core User Guide Revision History
1. About the LL 100GbE IP Core
2. Getting Started
3. Functional Description
4. Debugging the Link
A. Additional Information

2.8.2.2. Optimizing the IP Core Simulation With the Testbenches

In the testbench file, you can set the FASTSIM parameter and force values in the RO_SELS, BPOS, and WPOS parameters to enable simulation optimization. The testbench also specifies another IP core simulation optimization setting that you might need to modify for simulation in your own environment: AM_CNT_BITS.

To derive the values to which to force the RO_SELS, BPOS, and WPOS parameters, you must run your first simulation with some additional testbench code to display the simulation-derived values. For subsequent simulation runs with the same hardware design and simulator, you can force the values to these simulation-derived values to avoid the lengthy simulation required to achieve lane alignment. The process is particularly slow for this IP core because the IP core includes a soft processor that drives the lane alignment process. Forcing the parameters to the correct values for your design and simulator bypasses this process, increasing simulation efficiency.

The testbench file generated with the LL 100GbE IP core includes an initial block that displays the required force values. You can view the appropriate initial block for your IP core variation in the top-level testbench file you generate with your example design.

When you run simulation, this initial block prints values for the three parameters after lane alignment. Copy the values from standard output or from your log file and add the following lines to the testbench file, overwriting other forced values for these parameters if necessary: 

defparam dut.top_inst.FASTSIM = 1;
defparam dut.<variation_name>_inst.FORCE_BPOS = <required BPOS value>;
defparam dut.<variation_name>_inst.FORC_WPOS  = <required WPOS value>;
defparam dut.<variation_name>_inst.FORCE_RO_SELS = <required RO_SELS value>;
Note: Whether you use the Intel-provided testbench or your own custom testbench, you must update the testbench file with these lines and the derived values. The testbench file generated with the LL 100GbE IP core does not include the correct values, which depend on your IP core variation and simulation tool.

The AM_CNT_BITS parameter specifies the interval between expected alignment markers. The default value of this parameter is 14; this value specifies that alignment markers are inserted every 214 blocks, in compliance with the Ethernet specification. However, the testbench sets this parameter to the value of 6, to speed up simulation. In your own simulation environment, you must set this parameter to match the interval between incoming alignment markers to the IP core.

Level Two Title