AN 802: Intel® Stratix® 10 SoC Device Design Guidelines

Download PDF
ID 683117
Date 12/14/2020
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Introduction to the Intel® Stratix® 10 SoC Device Design Guidelines 2. Board Design Guidelines for Stratix 10 SoC FPGAs 3. Interfacing to the FPGA for Stratix 10 SoC FPGAs 4. System Considerations for Stratix 10 SoC FPGAs 5. Embedded Software Design Guidelines for Intel® Stratix® 10 SoC FPGAs 6. Recommended Resources for Stratix 10 SoC FPGAs
1. Introduction to the Intel® Stratix® 10 SoC Device Design Guidelines x
1.1. Introduction to the Stratix 10 SoC Device Design Guidelines Revision History
2. Board Design Guidelines for Stratix 10 SoC FPGAs x
2.1. Pin Connection Considerations for Board Design 2.2. HPS Clocking and Reset Design Considerations 2.3. Design Considerations for Connecting Device I/O to HPS Peripherals and Memory 2.4. Design Guidelines for HPS Interfaces 2.5. HPS EMIF Design Considerations 2.6. HPS Memory Debug 2.7. Boundary Scan for HPS 2.8. Embedded Software Debugging and Trace 2.9. Board Design Guidelines for Intel® Stratix® 10 SoC FPGAs Revision History
2.1. Pin Connection Considerations for Board Design x
2.1.1. Board-Related Intel® Quartus® Prime Settings
2.1.1. Board-Related Intel® Quartus® Prime Settings x
2.1.1.1. Unused Pins
2.2. HPS Clocking and Reset Design Considerations x
2.2.1. HPS Clock Planning 2.2.2. Early Pin Planning and I/O Assignment Analysis 2.2.3. Pin Features and Connections for HPS Clocks, Reset and PoR 2.2.4. Direct to Factory Pin Support for Remote System Update (RSU) Feature 2.2.5. Internal Clocks 2.2.6. HPS Peripheral Reset Management
2.3. Design Considerations for Connecting Device I/O to HPS Peripherals and Memory x
2.3.1. HPS Pin Multiplexing Design Considerations 2.3.2. HPS I/O Settings: Constraints and Drive Strengths
2.4. Design Guidelines for HPS Interfaces x
2.4.1. HPS EMAC PHY Interfaces 2.4.2. USB Interface Design Guidelines GUIDELINE: Intel® recommends that you design the board to support both USB PHY modes where the device supplies the clock versus where an external clock is the source. GUIDELINE: Ensure that the USB signal trace lengths are minimized. GUIDELINE: Ensure that signal integrity is considered. GUIDELINE: Design properly for OTG operation, if used. 2.4.3. SD/MMC and eMMC Card Interface Design Guidelines 2.4.4. Design Guidelines for Flash Interfaces 2.4.5. UART Interface Design Guidelines 2.4.6. I2C Interface Design Guidelines
2.4.1. HPS EMAC PHY Interfaces x
2.4.1.1. PHY Interfaces 2.4.1.2. PHY Interfaces Connected Through FPGA I/O 2.4.1.3. MDIO 2.4.1.4. Common PHY Interface Design Considerations
2.4.1.1. PHY Interfaces x
2.4.1.1.1. RMII 2.4.1.1.2. RGMII
2.4.1.2. PHY Interfaces Connected Through FPGA I/O x
2.4.1.2.1. GMII/MII 2.4.1.2.2. Adapting to RGMII 2.4.1.2.3. Adapting to RMII 2.4.1.2.4. Adapting to SGMII
2.4.1.4. Common PHY Interface Design Considerations x
2.4.1.4.1. Signal Integrity
2.4.4. Design Guidelines for Flash Interfaces x
2.4.4.1. NAND Flash Interface Design Guidelines
2.5. HPS EMIF Design Considerations x
2.5.1. Considerations for Connecting HPS to SDRAM 2.5.2. HPS SDRAM I/O Locations
3. Interfacing to the FPGA for Stratix 10 SoC FPGAs x
3.1. Overview of HPS Memory-Mapped Interfaces 3.2. Recommended System Topologies 3.3. Recommended Starting Point for HPS-to-FPGA Interface Designs 3.4. Timing Closure for FPGA Accelerators 3.5. Information on How to Configure and Use the Bridges 3.6. Interfacing to the FPGA for Intel® Stratix® 10 SoC FPGAs Revision History
3.1. Overview of HPS Memory-Mapped Interfaces x
3.1.1. HPS-to-FPGA Bridge 3.1.2. Lightweight HPS-to-FPGA Bridge 3.1.3. FPGA-to-HPS Bridge 3.1.4. FPGA-to-SDRAM Ports 3.1.5. Interface Bandwidths
3.2. Recommended System Topologies x
3.2.1. HPS Accesses to FPGA Fabric 3.2.2. MPU Sharing Data with FPGA 3.2.3. Examples of Cacheable and Non-Cacheable Data Accesses From the FPGA
3.2.3. Examples of Cacheable and Non-Cacheable Data Accesses From the FPGA x
3.2.3.1. Example 1: FPGA Reading Data from HPS SDRAM Directly 3.2.3.2. Example 2: FPGA Writing Data into HPS SDRAM Directly 3.2.3.3. Example 3: FPGA Reading Cache Coherent Data from HPS 3.2.3.4. Example 4: FPGA Writing Cache Coherent Data to HPS
4. System Considerations for Stratix 10 SoC FPGAs x
4.1. Timing Considerations 4.2. Maximizing Performance 4.3. System Level Cache Coherency 4.4. System Considerations for Stratix 10 SoC FPGAs Revision History
4.1. Timing Considerations x
4.1.1. Timing Closure for FPGA Accelerators 4.1.2. USB Interface Design Guidelines
4.1.1. Timing Closure for FPGA Accelerators x
4.1.1.1. HPS First and FPGA First Boot Considerations
5. Embedded Software Design Guidelines for Intel® Stratix® 10 SoC FPGAs x
5.1. Overview 5.2. Assembling the Components of Your Software Development Platform 5.3. Golden Hardware Reference Design (GHRD) 5.4. Selecting an Operating System for Your Application 5.5. Assembling Your Software Development Platform for Linux* 5.6. Assembling your Software Development Platform for a Bare-Metal Application 5.7. Assembling your Software Development Platform for Partner OS or RTOS 5.8. Choosing the Bootloader Software 5.9. Selecting Software Tools for Development, Debug and Trace 5.10. Boot And Configuration Considerations 5.11. System Reset Considerations 5.12. Flash Considerations 5.13. Embedded Software Debugging and Trace 5.14. Embedded Software Design Guidelines for Intel® Stratix® 10 SoC FPGAs Revision History
5.4. Selecting an Operating System for Your Application x
5.4.1. Using Linux* or RTOS 5.4.2. Developing a Bare-Metal Application 5.4.3. Using the Bootloader as a Bare-Metal Framework 5.4.4. Using Symmetrical vs. Asymmetrical Multiprocessing (SMP vs. AMP) Modes
5.5. Assembling Your Software Development Platform for Linux* x
5.5.1. Golden System Reference Design (GSRD) for Linux* 5.5.2. Source Code Management Considerations
5.9. Selecting Software Tools for Development, Debug and Trace x
5.9.1. Selecting Software Build Tools 5.9.2. Selecting Software Debug Tools 5.9.3. Selecting Software Trace Tools
5.10. Boot And Configuration Considerations x
5.10.1. Configuration Sources 5.10.2. Configuration Flash 5.10.3. Configuration Clock 5.10.4. Selecting HPS Boot Options 5.10.5. HPS Boot Sources 5.10.6. Remote System Update (RSU)
5.12. Flash Considerations x
5.12.1. Flash Programming Method 5.12.2. Using a Single flash for Both FPGA Configuration and HPS Mass Storage
6. Recommended Resources for Stratix 10 SoC FPGAs x
6.1. Device Documentation 6.2. Tools and Software Web Pages 6.3. Recommended Resources for Intel® Stratix® 10 SoC FPGAs Revision History
1. Introduction to the Intel® Stratix® 10 SoC Device Design Guidelines
2. Board Design Guidelines for Stratix 10 SoC FPGAs
3. Interfacing to the FPGA for Stratix 10 SoC FPGAs
4. System Considerations for Stratix 10 SoC FPGAs
5. Embedded Software Design Guidelines for Intel® Stratix® 10 SoC FPGAs
6. Recommended Resources for Stratix 10 SoC FPGAs

2.4.2. USB Interface Design Guidelines4.1.2. USB Interface Design Guidelines

The Intel® Stratix® 10 HPS can connect its embedded USB MACs directly to industry-standard USB 2.0 ULPI PHYs using the 1.8 V dedicated HPS I/O. No FPGA routing resources are used and timing is fixed, which simplifies design.

This guide describes the design guidelines covering all supported speeds of PHY operation: High-Speed (HS) 480 Mbps, Full-Speed (FS) 12 Mbps, and Low-Speed (LS) 1.5 Mbps.

GUIDELINE: Intel® recommends that you design the board to support both USB PHY modes where the device supplies the clock versus where an external clock is the source.

The Stratix 10 SoC Development Kit uses the Microchip USB3320 USB PHY. This device is known to work with the HPS USB module.

The interface between the ULPI MAC and PHY on the Intel® Stratix® 10 SoC consists of 8-bit data and the following control signals:
  • STP
  • NXT
  • DIR

Lastly a static clock of 60MHz is driven from the PHY or from an external oscillator and is required for operation, including some register accesses from the HPS to the USB MAC. Ensure the PHY manufacturer recommendations for RESET and power-up are followed.

If your USB PHY supports both input and output clock modes, Intel® recommends that you design your board to support both modes to mitigate potential timing issues. Typically, these modes are selected through passive bootstrap pins that are either pulled high or low.
  • Output Mode—In output clock mode, the clock is generated by the USB PHY. All signals are synchronized to this clock.
    Figure 5. Output Mode
  • Input Mode—In input clock mode, the PHY receives a clock from an external source. All signals are synchronized to the clock. In this mode, the clock can be generated by a PLL in the FPGA or by an external source.
    Figure 6. Input Mode

GUIDELINE: Ensure that the USB signal trace lengths are minimized.

At 60 MHz, the period is 16.67 ns and in that time, for example, the clock must travel from the external PHY to the MAC and then the data and control signals must travel from the MAC to the PHY. Because there is a round-trip delay, the maximum length of the clock and ULPI signals are important. Based on preliminary timing data the maximum length is recommended to be less than 7 inches. This is based on a PHY with a 5 ns Tco spec. If the specification is slower the total length must be shortened accordingly.
Figure 7. Trace Length
If there is little setup timing margin on the USB PHY end of the bus, sometimes you can switch the PHY to input clock mode and supply a 60 MHz clock source from the board.
Figure 8. System Diagram and Board Spec

GUIDELINE: Ensure that signal integrity is considered.

Signal integrity is important mostly on the CLK signal driven from the PHY to the MAC in the HPS. Because these signals are point-to-point with a maximum length, they can usually run unterminated but Intel® recommends to simulate the traces to make sure the reflections are minimized. Using the 50-ohm output setting from the FPGA is typically recommended unless the simulations show otherwise. A similar setting should be used from the PHY vendor if possible.

GUIDELINE: Design properly for OTG operation, if used.

When On-the-Go (OTG) functionality is used, the SoC can become a host or endpoint. When in host mode consider the power delivery, such as when you are supporting a USB Flash drive, or potentially a USB Hard Drive. These power requirements and reverse currents must be accounted for typically using external diodes and current limiters such as those used on the Intel FPGA development kits for Stratix 10 SoC.

For more information about the " Intel® Stratix® 10 SoC Development Board Schematics", refer to the Stratix 10 FPGA Development Kit User Guide.

Related Information
Level Two Title