JESD204B IP Core Design Example User Guide

Download PDF
ID 683094
Date 11/06/2017
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. JESD204B IP Core Design Example User Guide
1. JESD204B IP Core Design Example User Guide x
1.1. JESD204B Design Example Quick Start Guide 1.2. Supported Configurations 1.3. Generic Design Example 1.4. Presets 1.5. Selecting and Generating the Design Example 1.6. Design Example with RTL State Machine Control Unit 1.7. Design Example with Nios II Processor Control Unit 1.8. JESD204B IP Core Design Example Document Archives 1.9. JESD204B IP Core Design Example User Guide Document Revision History
1.1. JESD204B Design Example Quick Start Guide x
1.1.1. Directory Structure 1.1.2. Generating the Design 1.1.3. Compiling and Simulating the Design 1.1.4. Compiling and Testing the Design
1.1.2. Generating the Design x
1.1.2.1. Procedure 1.1.2.2. Design Example Parameters
1.1.3. Compiling and Simulating the Design x
1.1.3.1. Procedure
1.6. Design Example with RTL State Machine Control Unit x
1.6.1. Design Example Components 1.6.2. System Parameters 1.6.3. System Interface Signals 1.6.4. Example Feature: Dynamic Reconfiguration 1.6.5. Generating and Simulating the Design Example 1.6.6. Generating the Design Example For Compilation 1.6.7. Compiling the JESD204B IP Core Design Example
1.6.1. Design Example Components x
1.6.1.1. PLL 1.6.1.2. PLL Reconfiguration 1.6.1.3. Transceiver Reconfiguration Controller 1.6.1.4. Transceiver Reset Controller 1.6.1.5. Pattern Generator 1.6.1.6. Pattern Checker 1.6.1.7. Transport Layer 1.6.1.8. Serial Port Interface (SPI) 1.6.1.9. Control Unit
1.6.1.5. Pattern Generator x
1.6.1.5.1. Parallel PRBS Generator 1.6.1.5.2. Alternate Checkerboard Generator 1.6.1.5.3. Ramp Wave Generator
1.6.1.6. Pattern Checker x
1.6.1.6.1. Parallel PRBS Checker 1.6.1.6.2. Alternate Checkerboard Checker 1.6.1.6.3. Ramp Wave Checker
1.6.1.7. Transport Layer x
1.6.1.7.1. Supported System Configuration 1.6.1.7.2. Data Bit and Content Mapping Scheme 1.6.1.7.3. TX Path 1.6.1.7.4. RX Path
1.6.1.9. Control Unit x
1.6.1.9.1. Memory Block (ROM) 1.6.1.9.2. Finite State Machine (FSM)
1.6.2. System Parameters x
1.6.2.1. Run-Time Reconfiguration
1.6.4. Example Feature: Dynamic Reconfiguration x
1.6.4.1. Dynamic Reconfiguration Operation 1.6.4.2. MIF ROM
1.6.5. Generating and Simulating the Design Example x
1.6.5.1. Generating the Design Example Simulation Model 1.6.5.2. Simulating the JESD204B IP Core Design Example
1.7. Design Example with Nios II Processor Control Unit x
1.7.1. Design Example Components 1.7.2. System Clocking 1.7.3. Nios II Processor Design Example Files 1.7.4. Nios II Processor Design Example System Parameters 1.7.5. Nios II Processor Design Example System Interface Signals 1.7.6. Compiling the Design Example for Synthesis 1.7.7. Implementing the Design on the Development Kit 1.7.8. Running the Software Control Flow 1.7.9. Customizing the Design Example
1.7.1. Design Example Components x
1.7.1.1. Qsys System Component 1.7.1.2. Transport Layer 1.7.1.3. Test Pattern Generator 1.7.1.4. Test Pattern Checker
1.7.1.1. Qsys System Component x
1.7.1.1.1. JESD204B Subsystem in Qsys 1.7.1.1.2. Nios II Subsystem in Qsys 1.7.1.1.3. Core PLL 1.7.1.1.4. PLL Reconfiguration Controller 1.7.1.1.5. SPI Master
1.7.7. Implementing the Design on the Development Kit x
1.7.7.1. Pin Assignments 1.7.7.2. Hardware Setup 1.7.7.3. Programming the Device
1.7.8. Running the Software Control Flow x
1.7.8.1. Executing the Software C Code 1.7.8.2. Software Parameters 1.7.8.3. Software Interrupt Service Routines (ISR) 1.7.8.4. Software Functions Description
1.7.8.4. Software Functions Description x
1.7.8.4.1. Functions in main.c Source File 1.7.8.4.2. Custom Peripheral Access Macros in macros.c Source File
1.7.9. Customizing the Design Example x
1.7.9.1. Modifying the JESD204B IP Core Parameters Post-Generation 1.7.9.2. Changing the Data Rate or Reference Clock Frequency 1.7.9.3. Implementing a Multi-Link Design
1.7.9.3. Implementing a Multi-Link Design x
1.7.9.3.1. Editing the Qsys Project 1.7.9.3.2. Editing the Top Level HDL File 1.7.9.3.3. Editing the Software C Code
1. JESD204B IP Core Design Example User Guide

1.7.8.2. Software Parameters

The software parameters defined in the main header file, main.h, controls various behaviors of the C code.

Table 47.  Software Parameters
Parameter Default Value Description
DEBUG_MODE 0 Set to 1 to print debug messages, else set to 0.
PRINT_INTERRUPT_MESSAGES 1 Set to 1 to print JESD204B error interrupt messages, else set to 0.
PATCHK_EN 1 Set to 1 when test pattern checker is included in the initial design data path configuration, else set to 0.
DATAPATH 3

Set to indicate the JESD204B IP configuration:

1 – TX data path only.

2 – RX data path only.

3 – Duplex data path (TX and RX data path).
MAX_LINKS 1

Set to indicate the number of links in the design (for example, for dual link, set MAX_LINKS=2). See Implementing a Multi-Link Design section for more detailed instructions on implementing multi-link use case.

Note: When using the design as-is, the maximum value of MAX_LINKS is 16. To increase the limit, redesign the address map in Qsys.
LOOPBACK_INIT 1 Initial value of the loopback. Set to 1 for internal serial loopback mode, else set to 0.
SOURCEDEST_INIT PRBS

Initial value of source/destination. Set to indicate test pattern generator or checker type or user mode:

USER – User mode (no test pattern generator or checker in data path).

ALT – Test pattern generator or checker set in alternate checkerboard mode.

RAMP – Test pattern generator or checker set in ramp wave mode.

PRBS – Test pattern generator or checker set in parallel PRBS mode.

Level Two Title