Visible to Intel only — GUID: mwh1409959568564
Ixiasoft
1.1. Using Provided HDL Templates
1.2. Instantiating IP Cores in HDL
1.3. Inferring Multipliers and DSP Functions
1.4. Inferring Memory Functions from HDL Code
1.5. Register and Latch Coding Guidelines
1.6. General Coding Guidelines
1.7. Designing with Low-Level Primitives
1.8. Recommended HDL Coding Styles Revision History
1.4.1.1. Use Synchronous Memory Blocks
1.4.1.2. Avoid Unsupported Reset and Control Conditions
1.4.1.3. Check Read-During-Write Behavior
1.4.1.4. Controlling RAM Inference and Implementation
1.4.1.5. Single-Clock Synchronous RAM with Old Data Read-During-Write Behavior
1.4.1.6. Single-Clock Synchronous RAM with New Data Read-During-Write Behavior
1.4.1.7. Simple Dual-Port, Dual-Clock Synchronous RAM
1.4.1.8. True Dual-Port Synchronous RAM
1.4.1.9. Mixed-Width Dual-Port RAM
1.4.1.10. RAM with Byte-Enable Signals
1.4.1.11. Specifying Initial Memory Contents at Power-Up
1.6.6.1. If Performance is Important, Optimize for Speed
1.6.6.2. Use Separate CRC Blocks Instead of Cascaded Stages
1.6.6.3. Use Separate CRC Blocks Instead of Allowing Blocks to Merge
1.6.6.4. Take Advantage of Latency if Available
1.6.6.5. Save Power by Disabling CRC Blocks When Not in Use
1.6.6.6. Initialize the Device with the Synchronous Load (sload) Signal
3.4.1. Apply Complete System-Centric Timing Constraints for the Timing Analyzer
3.4.2. Force the Identification of Synchronization Registers
3.4.3. Set the Synchronizer Data Toggle Rate
3.4.4. Optimize Metastability During Fitting
3.4.5. Increase the Length of Synchronizers to Protect and Optimize
3.4.6. Increase the Number of Stages Used in Synchronizers
3.4.7. Select a Faster Speed Grade Device
Visible to Intel only — GUID: mwh1409959568564
Ixiasoft
2.6. Recommended Design Practices Revision History
The following revision history applies to this chapter:
Document Version | Intel® Quartus® Prime Version | Changes |
---|---|---|
2021.10.04 | 21.3 |
|
2021.03.29 | 21.1 |
|
2020.09.28 | 20.3 |
|
2020.04.13 | 20.1 |
|
2019.11.01 | 19.3.0 |
|
2019.09.30 | 19.3.0 |
|
2019.04.01 | 19.1.0 |
|
2018.09.24 | 18.1.0 |
|
2017.11.06 | 17.1.0 |
|
2017.05.08 | 17.0.0 |
|
2016.10.31 | 16.1.0 |
|
2016.05.03 | 16.0.0 |
|
2015.11.02 | 15.1.0 |
|
2014.12.15 | 14.1.0 | Updated location of Fitter Settings, Analysis & Synthesis Settings, and Physical Optimization Settings to Compiler Settings. |
June 2014 | 14.0.0 | Removed references to obsolete MegaWizard Plug-In Manager. |
November 2013 | 13.1.0 | Removed HardCopy device information. |
May 2013 | 13.0.0 | Removed PrimeTime support. |
June 2012 | 12.0.0 | Removed survey link. |
November 2011 | 11.0.1 | Template update. |
May 2011 | 11.0.0 | Added information to Reset Resources . |
December 2010 | 10.1.0 |
|
July 2010 | 10.0.0 |
|
November 2009 | 9.1.0 |
|
March 2009 | 9.0.0 |
|
November 2008 | 8.1.0 |
|
May 2008 | 8.0.0 |
|