External Memory Interfaces Agilex™ 7 M-Series FPGA IP User Guide

Download PDF
ID 772538
Date 7/08/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the External Memory Interfaces Agilex™ 7 M-Series FPGA IP 2. Agilex™ 7 M-Series FPGA EMIF IP – Introduction 3. Agilex™ 7 M-Series FPGA EMIF IP – Product Architecture 4. Agilex™ 7 M-Series FPGA EMIF IP – End-User Signals 5. Agilex™ 7 M-Series FPGA EMIF IP – Simulating Memory IP 6. Agilex™ 7 M-Series FPGA EMIF IP – DDR4 Support 7. Agilex™ 7 M-Series FPGA EMIF IP – DDR5 Support 8. Agilex™ 7 M-Series FPGA EMIF IP – LPDDR5 Support 9. Agilex™ 7 M-Series FPGA EMIF IP – Timing Closure 10. Agilex™ 7 M-Series FPGA EMIF IP – Controller Optimization 11. Agilex™ 7 M-Series FPGA EMIF IP – Debugging 12. Document Revision History for External Memory Interfaces Agilex™ 7 M-Series FPGA IP User Guide
1. About the External Memory Interfaces Agilex™ 7 M-Series FPGA IP x
1.1. Release Information
2. Agilex™ 7 M-Series FPGA EMIF IP – Introduction x
2.1. Agilex™ 7 M-Series EMIF IP Protocol and Feature Support 2.2. Agilex™ 7 M-Series EMIF IP Design Flow 2.3. Agilex™ 7 M-Series EMIF IP Design Checklist
3. Agilex™ 7 M-Series FPGA EMIF IP – Product Architecture x
3.1. Agilex™ 7 M-Series EMIF Architecture: Introduction 3.2. Agilex™ 7 M-Series EMIF Sequencer 3.3. Agilex™ 7 M-Series EMIF Controller 3.4. Agilex™ 7 M-Series EMIF IP for Hard Processor Subsystem (HPS)
3.1. Agilex™ 7 M-Series EMIF Architecture: Introduction x
3.1.1. Agilex™ 7 M-Series EMIF Architecture: I/O Subsystem 3.1.2. Agilex™ 7 M-Series EMIF Architecture: I/O SSM 3.1.3. Agilex™ 7 M-Series EMIF Architecture: I/O Bank 3.1.4. Agilex™ 7 M-Series EMIF Architecture: I/O Lane 3.1.5. Agilex™ 7 M-Series EMIF Architecture: Input DQS Clock Tree 3.1.6. Agilex™ 7 M-Series EMIF Architecture: PHY Clock Tree 3.1.7. Agilex™ 7 M-Series EMIF Architecture: PLL Reference Clock Networks 3.1.8. Agilex™ 7 M-Series EMIF Architecture: Clock Phase Alignment 3.1.9. User Clock in Different Core Access Modes
3.1.3. Agilex™ 7 M-Series EMIF Architecture: I/O Bank x
3.1.3.1. Lockstep Configuration 3.1.3.2. DDR4 Pin Placement 3.1.3.3. DDR5 Pin Placement 3.1.3.4. LPDDR5 Pin Placement 3.1.3.5. I/O Sub-Bank Usage
3.2. Agilex™ 7 M-Series EMIF Sequencer x
3.2.1. Agilex™ 7 M-Series Mailbox Structure and Register Definitions
3.2.1. Agilex™ 7 M-Series Mailbox Structure and Register Definitions x
3.2.1.1. Mailbox Supported Commands 3.2.1.2. Mailbox Command Definitions
3.3. Agilex™ 7 M-Series EMIF Controller x
3.3.1. Hard Memory Controller
3.3.1. Hard Memory Controller x
3.3.1.1. Hard Memory Controller Features
4. Agilex™ 7 M-Series FPGA EMIF IP – End-User Signals x
4.1. Agilex™ 7 M-Series EMIF IP Interfaces for DDR4 4.2. Agilex™ 7 M-Series EMIF IP Interfaces for DDR5 4.3. Agilex™ 7 M-Series EMIF IP Interfaces for LPDDR5 4.4. Agilex™ 7 M-Series EMIF IP Interfaces for Calibration Component
4.1. Agilex™ 7 M-Series EMIF IP Interfaces for DDR4 x
4.1.1. ref_clk for External Memory Interfaces (EMIF) IP 4.1.2. core_init_n for External Memory Interfaces (EMIF) IP 4.1.3. usr_async_clk for External Memory Interfaces (EMIF) IP 4.1.4. usr_clk for External Memory Interfaces (EMIF) IP 4.1.5. usr_rst_n for External Memory Interfaces (EMIF) IP 4.1.6. s0_axi4 for External Memory Interfaces (EMIF) IP 4.1.7. mem for External Memory Interfaces (EMIF) IP 4.1.8. oct for External Memory Interfaces (EMIF) IP
4.2. Agilex™ 7 M-Series EMIF IP Interfaces for DDR5 x
4.2.1. ref_clk for External Memory Interfaces (EMIF) IP 4.2.2. core_init_n for External Memory Interfaces (EMIF) IP 4.2.3. usr_async_clk for External Memory Interfaces (EMIF) IP 4.2.4. usr_clk for External Memory Interfaces (EMIF) IP 4.2.5. usr_rst_n for External Memory Interfaces (EMIF) IP 4.2.6. s0_axi4 for External Memory Interfaces (EMIF) IP 4.2.7. mem for External Memory Interfaces (EMIF) IP 4.2.8. i3c for External Memory Interfaces (EMIF) IP 4.2.9. mem_lbd for External Memory Interfaces (EMIF) IP 4.2.10. mem_lbs for External Memory Interfaces (EMIF) IP 4.2.11. oct for External Memory Interfaces (EMIF) IP
4.3. Agilex™ 7 M-Series EMIF IP Interfaces for LPDDR5 x
4.3.1. ref_clk for External Memory Interfaces (EMIF) IP 4.3.2. core_init_n for External Memory Interfaces (EMIF) IP 4.3.3. usr_async_clk for External Memory Interfaces (EMIF) IP 4.3.4. usr_clk for External Memory Interfaces (EMIF) IP 4.3.5. usr_rst_n for External Memory Interfaces (EMIF) IP 4.3.6. s0_axi4 for External Memory Interfaces (EMIF) IP 4.3.7. mem for External Memory Interfaces (EMIF) IP 4.3.8. oct for External Memory Interfaces (EMIF) IP
4.4. Agilex™ 7 M-Series EMIF IP Interfaces for Calibration Component x
4.4.1. s0_axi4lite_clk for External Memory Interface Calibration Component 4.4.2. s0_axi4lite_rst_n for External Memory Interface Calibration Component 4.4.3. s0_axil for External Memory Interface Calibration Component
5. Agilex™ 7 M-Series FPGA EMIF IP – Simulating Memory IP x
5.1. Simulation Walkthrough
5.1. Simulation Walkthrough x
5.1.1. Calibration 5.1.2. Simulation Scripts 5.1.3. Functional Simulation with Verilog HDL 5.1.4. Simulating the Design Example
6. Agilex™ 7 M-Series FPGA EMIF IP – DDR4 Support x
6.1. Agilex™ 7 M-Series FPGA EMIF IP Parameters for DDR4 6.2. Agilex™ 7 M-Series FPGA EMIF IP Pin and Resource Planning 6.3. DDR4 Board Design Guidelines
6.1. Agilex™ 7 M-Series FPGA EMIF IP Parameters for DDR4 x
6.1.1. Agilex™ 7 M-Series FPGA EMIF IP Parameter Descriptions for DDR4 6.1.2. Agilex™ 7 M-Series FPGA EMIF Memory Device IP Parameter Descriptions for DDR4 6.1.3. Agilex™ 7 M-Series FPGA EMIF Calibration IP Parameter Descriptions
6.2. Agilex™ 7 M-Series FPGA EMIF IP Pin and Resource Planning x
6.2.1. Agilex™ 7 M-Series FPGA EMIF IP Interface Pins 6.2.2. Agilex™ 7 M-Series FPGA EMIF IP Resources 6.2.3. Pin Guidelines for Agilex™ 7 M-Series FPGA EMIF IP 6.2.4. Pin Placements for Agilex™ 7 M-Series FPGA DDR4 EMIF IP
6.2.1. Agilex™ 7 M-Series FPGA EMIF IP Interface Pins x
6.2.1.1. Estimating Pin Requirements 6.2.1.2. DIMM Options 6.2.1.3. Maximum Number of Interfaces
6.2.2. Agilex™ 7 M-Series FPGA EMIF IP Resources x
6.2.2.1. OCT 6.2.2.2. PLL
6.2.4. Pin Placements for Agilex™ 7 M-Series FPGA DDR4 EMIF IP x
6.2.4.1. Address and Command Pin Placement for DDR4 6.2.4.2. DDR4 Data Width Mapping 6.2.4.3. General Guidelines - DDR4 6.2.4.4. x4 DIMM Implementation 6.2.4.5. Specific Pin Connection Requirements 6.2.4.6. Command and Address Signals 6.2.4.7. Clock Signals 6.2.4.8. Data, Data Strobes, DM/DBI, and Optional ECC Signals
6.3. DDR4 Board Design Guidelines x
6.3.1. Terminations for DDR4 with Agilex™ 7 M-Series Devices 6.3.2. General Layout Routing Guidelines 6.3.3. Reference Stackup 6.3.4. Agilex™ 7 M-Series EMIF-Specific Routing Guidelines for Various DDR4 Topologies 6.3.5. DDR4 Routing Guidelines: Discrete (Component) Topologies
6.3.1. Terminations for DDR4 with Agilex™ 7 M-Series Devices x
6.3.1.1. Dynamic On-Chip Termination (OCT) 6.3.1.2. Dynamic On-Die Termination (ODT) in DDR4 6.3.1.3. Choosing Terminations on Agilex™ 7 M-Series FPGA Devices 6.3.1.4. On-Chip Termination Recommendations for Agilex™ 7 M-Series FPGA Devices
6.3.4. Agilex™ 7 M-Series EMIF-Specific Routing Guidelines for Various DDR4 Topologies x
6.3.4.1. One DIMM per Channel (1DPC) for UDIMM, RDIMM, and SODIMM DDR4 Topologies 6.3.4.2. Skew Matching Guidelines for DIMM Configurations 6.3.4.3. Power Delivery Recommendations for the Memory / DIMM Side
6.3.5. DDR4 Routing Guidelines: Discrete (Component) Topologies x
6.3.5.1. Single Rank x 8 Discrete (Component) Topology 6.3.5.2. Single Rank x 16 Discrete (Component) Topology 6.3.5.3. ADDR/CMD Reference Voltage/RESET Signal Routing Guidelines for Single Rank x 8 and Single Rank x 16 Discrete (Component) Topologies 6.3.5.4. Skew Matching Guidelines for DDR4 Discrete Configurations 6.3.5.5. Power Delivery Recommendations for DDR4 Discrete Configurations 6.3.5.6. Agilex™ 7 M-Series EMIF Pin Swapping Guidelines
6.3.5.6. Agilex™ 7 M-Series EMIF Pin Swapping Guidelines x
6.3.5.6.1. DDR4 Byte Lane Swapping 6.3.5.6.2. DDR4 Address and Command and CLK Lane 6.3.5.6.3. DDR4 Interface x8 Data Lane 6.3.5.6.4. DDR4 Interface x4 Data Lane 6.3.5.6.5. Pin Swizzling
7. Agilex™ 7 M-Series FPGA EMIF IP – DDR5 Support x
7.1. Agilex™ 7 M-Series FPGA EMIF IP Parameters for DDR5 7.2. Agilex™ 7 M-Series FPGA EMIF IP Pin and Resource Planning 7.3. DDR5 Board Design Guidelines
7.1. Agilex™ 7 M-Series FPGA EMIF IP Parameters for DDR5 x
7.1.1. Agilex™ 7 M-Series FPGA EMIF IP Parameter Descriptions for DDR5 7.1.2. Agilex™ 7 M-Series FPGA EMIF Memory Device IP Parameter Descriptions for DDR5 7.1.3. Agilex™ 7 M-Series FPGA EMIF Calibration IP Parameter Descriptions
7.2. Agilex™ 7 M-Series FPGA EMIF IP Pin and Resource Planning x
7.2.1. Agilex™ 7 M-Series FPGA EMIF IP Interface Pins 7.2.2. Agilex™ 7 M-Series FPGA EMIF IP Resources 7.2.3. Pin Guidelines for Agilex™ 7 M-Series FPGA EMIF IP 7.2.4. Pin Placements for Agilex™ 7 M-Series FPGA DDR5 EMIF IP 7.2.5. Agilex™ 7 M-Series EMIF Pin Swapping Guidelines
7.2.1. Agilex™ 7 M-Series FPGA EMIF IP Interface Pins x
7.2.1.1. Estimating Pin Requirements 7.2.1.2. DIMM Options 7.2.1.3. Maximum Number of Interfaces
7.2.2. Agilex™ 7 M-Series FPGA EMIF IP Resources x
7.2.2.1. OCT 7.2.2.2. PLL
7.2.3. Pin Guidelines for Agilex™ 7 M-Series FPGA EMIF IP x
7.2.3.1. General Guidelines - DDR5 7.2.3.2. x4 DIMM Implementation 7.2.3.3. Specific Pin Connection Requirements 7.2.3.4. Command and Address Signals 7.2.3.5. Clock Signals 7.2.3.6. Data, Data Strobes, DM, and Optional ECC Signals
7.2.4. Pin Placements for Agilex™ 7 M-Series FPGA DDR5 EMIF IP x
7.2.4.1. Address and Command Pin Placement for DDR5 7.2.4.2. DDR5 Data Width Mapping
7.2.5. Agilex™ 7 M-Series EMIF Pin Swapping Guidelines x
7.2.5.1. DDR5 Byte Lane Swapping 7.2.5.2. DDR5 Address and Command and CLK Lane 7.2.5.3. DDR5 Interface x8 Data Lane 7.2.5.4. DDR5 Interface x4 Data Lane 7.2.5.5. Pin Swizzling
7.3. DDR5 Board Design Guidelines x
7.3.1. PCB Stack-up and Design Considerations 7.3.2. General Design Considerations 7.3.3. DDR Differential Signals Routing 7.3.4. Ground Plane and Return Path 7.3.5. RDIMM, UDIMM, and SODIMM Break-in Layout Guidelines 7.3.6. DRAM Break-in Layout Guidelines 7.3.7. DDR5 PCB Layout Guidelines 7.3.8. DDR5 Simulation Strategy
7.3.7. DDR5 PCB Layout Guidelines x
7.3.7.1. DDR5 Discrete Component/Memory Down Topology: up to 40-Bit Interface (1 Rank x8 or x16, 2 Rank x8 or x16) 7.3.7.2. Routing Guidelines for DDR5 Memory Down: 1 Rank or 2 Rank (x8 bit or x16 bit) Configurations 7.3.7.3. Routing Guidelines for DDR5 RDIMM, UDIMM, and SODIMM Configurations 7.3.7.4. Example of a DDR5 layout on an Altera FPGA Platform Board
8. Agilex™ 7 M-Series FPGA EMIF IP – LPDDR5 Support x
8.1. Agilex™ 7 M-Series FPGA EMIF IP Parameters for LPDDR5 8.2. Agilex™ 7 M-Series FPGA EMIF IP Pin and Resource Planning 8.3. LPDDR5 Board Design Guidelines
8.1. Agilex™ 7 M-Series FPGA EMIF IP Parameters for LPDDR5 x
8.1.1. Agilex™ 7 M-Series FPGA EMIF IP Parameter Descriptions for LPDDR5 8.1.2. Agilex™ 7 M-Series FPGA EMIF Memory Device IP Parameter Descriptions for LPDDR5 8.1.3. Agilex™ 7 M-Series FPGA EMIF Calibration IP Parameter Descriptions
8.2. Agilex™ 7 M-Series FPGA EMIF IP Pin and Resource Planning x
8.2.1. Agilex™ 7 M-Series FPGA EMIF IP Interface Pins 8.2.2. Agilex™ 7 M-Series FPGA EMIF IP Resources 8.2.3. Pin Guidelines for Agilex™ 7 M-Series FPGA EMIF IP 8.2.4. Pin Placements for Agilex™ 7 M-Series FPGA LPDDR5 EMIF IP
8.2.1. Agilex™ 7 M-Series FPGA EMIF IP Interface Pins x
8.2.1.1. Estimating Pin Requirements 8.2.1.2. DIMM Options 8.2.1.3. Maximum Number of Interfaces
8.2.2. Agilex™ 7 M-Series FPGA EMIF IP Resources x
8.2.2.1. OCT 8.2.2.2. PLL
8.2.3. Pin Guidelines for Agilex™ 7 M-Series FPGA EMIF IP x
8.2.3.1. General Guidelines - LPDDR5 8.2.3.2. Specific Pin Connection Requirements 8.2.3.3. Command and Address Signals 8.2.3.4. Clock Signals
8.2.4. Pin Placements for Agilex™ 7 M-Series FPGA LPDDR5 EMIF IP x
8.2.4.1. Address and Command Pin Placement for LPDDR5 8.2.4.2. LPDDR5 Data Width Mapping 8.2.4.3. LPDDR5 Byte Lane Swapping
8.3. LPDDR5 Board Design Guidelines x
8.3.1. PCB Stack-up and Design Considerations 8.3.2. General Design Considerations 8.3.3. DDR Differential Signals Routing 8.3.4. Ground Plane and Return Path 8.3.5. DRAM Break-in Layout Guidelines 8.3.6. LPDDR5 PCB Layout Guidelines 8.3.7. LPDDR5 Simulation Strategy
8.3.6. LPDDR5 PCB Layout Guidelines x
8.3.6.1. LPDDR5 Discrete Component/Memory Down Topology (1 Rank or 2 Rank, up to 64 Bit Interface) 8.3.6.2. Supported LPDDR5 Topologies 8.3.6.3. Example of an LPDDR5 Layout on an Altera® FPGA Platform Board
9. Agilex™ 7 M-Series FPGA EMIF IP – Timing Closure x
9.1. Timing Closure 9.2. Optimizing Timing
9.1. Timing Closure x
9.1.1. Timing Analysis
9.1.1. Timing Analysis x
9.1.1.1. PHY or Core
10. Agilex™ 7 M-Series FPGA EMIF IP – Controller Optimization x
10.1. Interface Standard 10.2. Bank Management Efficiency 10.3. Data Transfer 10.4. Improving Controller Efficiency
10.4. Improving Controller Efficiency x
10.4.1. Frequency of Operation 10.4.2. Series of Reads or Writes 10.4.3. AXI to Memory Mapping
11. Agilex™ 7 M-Series FPGA EMIF IP – Debugging x
11.1. Interface Configuration Performance Issues 11.2. Functional Issue Evaluation 11.3. Timing Issue Characteristics 11.4. Verifying Memory IP Using the Signal Tap Logic Analyzer 11.5. Debugging with the External Memory Interface Debug Toolkit 11.6. Generating Traffic with the Test Engine IP 11.7. Guidelines for Developing HDL for Traffic Generator 11.8. Guidelines for Traffic Generator Status Check
11.1. Interface Configuration Performance Issues x
11.1.1. Interface Configuration Bottleneck and Efficiency Issues
11.2. Functional Issue Evaluation x
11.2.1. Altera IP Memory Model 11.2.2. Vendor Memory Model 11.2.3. Transcript Window Messages
11.3. Timing Issue Characteristics x
11.3.1. Evaluating FPGA Timing Issues 11.3.2. Evaluating External Memory Interface Timing Issues
11.5. Debugging with the External Memory Interface Debug Toolkit x
11.5.1. Prerequisites for Using the EMIF Debug Toolkit 11.5.2. Configuring Your Design to Use the EMIF Debug Toolkit 11.5.3. Launching the EMIF Debug Toolkit 11.5.4. Using the EMIF Debug Toolkit
11.5.4. Using the EMIF Debug Toolkit x
11.5.4.1. Rerunning Calibration 11.5.4.2. Rerunning the Test Engine 11.5.4.3. Saving Debug Print 11.5.4.4. Calibration Reports 11.5.4.5. Driver Margining Tab 11.5.4.6. Pin Delay Settings Tab
11.8. Guidelines for Traffic Generator Status Check x
11.8.1. Status Check Using the Signal Tap Logic Analyzer 11.8.2. Exporting the Status Interface to the Top-Level Design
1. About the External Memory Interfaces Agilex™ 7 M-Series FPGA IP
2. Agilex™ 7 M-Series FPGA EMIF IP – Introduction
3. Agilex™ 7 M-Series FPGA EMIF IP – Product Architecture
4. Agilex™ 7 M-Series FPGA EMIF IP – End-User Signals
5. Agilex™ 7 M-Series FPGA EMIF IP – Simulating Memory IP
6. Agilex™ 7 M-Series FPGA EMIF IP – DDR4 Support
7. Agilex™ 7 M-Series FPGA EMIF IP – DDR5 Support
8. Agilex™ 7 M-Series FPGA EMIF IP – LPDDR5 Support
9. Agilex™ 7 M-Series FPGA EMIF IP – Timing Closure
10. Agilex™ 7 M-Series FPGA EMIF IP – Controller Optimization
11. Agilex™ 7 M-Series FPGA EMIF IP – Debugging
12. Document Revision History for External Memory Interfaces Agilex™ 7 M-Series FPGA IP User Guide

7.3. DDR5 Board Design Guidelines

This section provides board layout design recommendations and guidelines for Agilex™ 7 M-Series FPGAs, with GPIO-B (input/output) silicon implementation to support DDR5.

This PCB layout guideline covers various supported DDR5 topologies along with maximum supported data rate that you can use for a successful PCB design.

A successful PCB design requires not only following the topology and routing guidelines here, but must also meet PDN design requirements.

For related information, refer also to the Agilex™ 7 F, I, and M-Series PDN design guidelines and the Agilex™ 7 high speed transceiver PCB design guidelines, available on the Intel website.


Section Content
PCB Stack-up and Design Considerations
General Design Considerations
DDR Differential Signals Routing
Ground Plane and Return Path
RDIMM, UDIMM, and SODIMM Break-in Layout Guidelines
DRAM Break-in Layout Guidelines
DDR5 PCB Layout Guidelines
DDR5 Simulation Strategy

Level Two Title