MACsec Intel® FPGA System Design User Guide

Download PDF
ID 767516
Date 10/02/2023
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Introduction 2. Architecture 3. Interface Overview 4. Parameters 5. Configuration Registers 6. Software Architecture 7. Generating the System Design 8. Document Revision History for MACsec System Design User Guide A. Release Notes
1. Introduction x
1.1. Terminology 1.2. Release Information 1.3. System Requirements
2. Architecture x
2.1. System Architecture 2.2. Data Path Between Ethernet MAC and MACsec 2.3. Data Path Between MACsec and MCDMA 2.4. Data Path Between MACsec and Packet Generator/Checker (Packet Client) 2.5. Data Path Illustrations 2.6. Interrupts 2.7. Packet FIFO 2.8. AXI-ST Rate Controller 2.9. Error Handling 2.10. Top Level Signals
2.2. Data Path Between Ethernet MAC and MACsec x
2.2.1. Ethernet Subsystem
2.2.1. Ethernet Subsystem x
2.2.1.1. Data Receiving from MACsec to E/F-Tile Hard IP 2.2.1.2. Data Transmitting from E/F-tile Hard IP to MACsec 2.2.1.3. Order of Ethernet Transmission 2.2.1.4. E/F-Tile Hard IP Reset Sequence
2.3. Data Path Between MACsec and MCDMA x
2.3.1. AXI-ST Multi-Segment to Single-Segment Conversion 2.3.2. MCDMA
2.4. Data Path Between MACsec and Packet Generator/Checker (Packet Client) x
2.4.1. Packet Client 2.4.2. Packet Generation and Check
2.5. Data Path Illustrations x
2.5.1. MACsec Interface Signal Names
2.6. Interrupts x
2.6.1. MCDMA MSI-X Table Configuration
3. Interface Overview x
3.1. Clocking 3.2. Resets
5. Configuration Registers x
5.1. System Register Map
5.1. System Register Map x
5.1.1. Packet Client Register Map 5.1.2. Interrupt Controller Register Map
6. Software Architecture x
6.1. MACsec Key Agreement Protocol 6.2. Driver Functional Requirements 6.3. Software Requirements 6.4. Software Overview 6.5. MACsec IP APIs Sequence 6.6. Functions 6.7. Software Tools
6.4. Software Overview x
6.4.1. McDMA Driver Kernel Module 6.4.2. MACsec IP APIs 6.4.3. Linux MACsec Driver Kernel Module 6.4.4. IP Tool 6.4.5. WPA Supplicant
6.4.2. MACsec IP APIs x
6.4.2.1. SDK
6.5. MACsec IP APIs Sequence x
6.5.1. MACsec Initialization Sequence
6.5.1. MACsec Initialization Sequence x
6.5.1.1. MACsec Reset Sequence 6.5.1.2. TX Configuration Sequence 6.5.1.3. RX Configuration Sequence 6.5.1.4. TX Rekeying Sequence 6.5.1.5. RX Rekeying Sequence 6.5.1.6. Cut Through/Store Forward Mode 6.5.1.7. User Single/Multi Port Settings 6.5.1.8. Encrypt/Decrypt Port 6.5.1.9. Port Priority 6.5.1.10. Interrupt Generation and Register
6.5.1.1. MACsec Reset Sequence x
6.5.1.1.1. GLOBAL Reset 6.5.1.1.2. PORT Reset 6.5.1.1.3. Secure Association (SA) Reset
6.6. Functions x
6.6.1. macsec_initilize 6.6.2. macsec_get_attributes 6.6.3. macsec_get_sa_attributes 6.6.4. macsec_set_attributes 6.6.5. macsec_set_sa_attributes 6.6.6. macsec_read_register 6.6.7. macsec_write_register 6.6.8. macsec_set_port_configuration 6.6.9. macsec_rate_configuration 6.6.10. macsec_single_or_multi_port 6.6.11. macsec_crypto_mode 6.6.12. macsec_port_priority 6.6.13. macsec_register_isr
6.7. Software Tools x
6.7.1. IP Tool 6.7.2. WPA_Supplicant 6.7.3. CLI Debug Tool
6.7.3. CLI Debug Tool x
6.7.3.1. Functional Requirements 6.7.3.2. Features Overview 6.7.3.3. Design with HOST 6.7.3.4. Netlink Interface 6.7.3.5. SDK 6.7.3.6. Design Overview
7. Generating the System Design x
7.1. Software Requirements 7.2. Obtaining the Reference Design 7.3. Reference Design Directory Structure 7.4. Simulation Command Arguments 7.5. Simulation Test Cases 7.6. Complete Simulation Command 7.7. Simulation Requirements 7.8. Running Non-UVM Simulation 7.9. Running UVM Simulation 7.10. Building, Installing, and Running the Software 7.11. Building the Hardware Design
7.4. Simulation Command Arguments x
7.4.1. Simulation -d Options
1. Introduction
2. Architecture
3. Interface Overview
4. Parameters
5. Configuration Registers
6. Software Architecture
7. Generating the System Design
8. Document Revision History for MACsec System Design User Guide
A. Release Notes

6.4.4. IP Tool

The IP Tool is used to configure transmit/receive secure associations and channels. It configures the IEEE Std 802.1AE (MAC security) keys for a particular MACsec type interface.

The Linux MACsec driver and IP Tool uses rtnetlink and genetlink APIs to handle the input commands. Rtnetlink creates and sets up the net device whereas the genetlink APIs are used to set up transmit and receive secure associations on a MACsec device.

The MACsec IP driver provides read/write APIs to configure the CSR region of the MACsec HW FPGA.

Level Two Title