F-Tile JESD204B Intel® FPGA IP User Guide

Download PDF
ID 723907
Date 4/23/2024
Public
Document Table of Contents
Document Table of Contents x
1. F-Tile JESD204B IP Quick Reference 2. About the F-Tile JESD204B Intel® FPGA IP 3. Getting Started 4. F-Tile JESD204B IP Functional Description 5. F-Tile JESD204B IP Deterministic Latency Implementation Guidelines 6. F-Tile JESD204B IP Debug Guidelines 7. F-Tile JESD204B Intel FPGA IP User Guide Archives 8. Document Revision History for the F-Tile JESD204B Intel® FPGA IP User Guide
2. About the F-Tile JESD204B Intel® FPGA IP x
2.1. Release Information 2.2. Device Family Support 2.3. Datapath Modes 2.4. IP Variation 2.5. F-Tile JESD204B IP Configuration 2.6. Channel Bonding 2.7. Performance and Resource Utilization
3. Getting Started x
3.1. Introduction to Intel® FPGA IP Cores 3.2. Installing and Licensing Intel® FPGA IP Cores 3.3. Intel® FPGA IP Evaluation Mode 3.4. Upgrading IP Cores 3.5. IP Catalog and Parameter Editor 3.6. Design Walkthrough 3.7. F-Tile JESD204B IP Design Considerations 3.8. F-Tile JESD204B Intel® FPGA IP Parameters 3.9. F-Tile JESD204B IP Component Files
3.6. Design Walkthrough x
3.6.1. Creating a New Quartus® Prime Project 3.6.2. Parameterizing and Generating the IP 3.6.3. Compiling the F-Tile JESD204B IP Core Design 3.6.4. Programming an FPGA Device
3.7. F-Tile JESD204B IP Design Considerations x
3.7.1. Integrating the F-Tile JESD204B IP in Platform Designer 3.7.2. Pin Assignments 3.7.3. Adding External System PLL
4. F-Tile JESD204B IP Functional Description x
4.1. Transmitter 4.2. Receiver 4.3. Operation 4.4. Clocking Scheme 4.5. Reset Scheme 4.6. Signals 4.7. Registers
4.1. Transmitter x
4.1.1. TX Data Link Layer 4.1.2. TX PHY Layer
4.1.1. TX Data Link Layer x
4.1.1.1. TX CGS 4.1.1.2. TX ILAS 4.1.1.3. User Data Phase
4.2. Receiver x
4.2.1. RX Data Link Layer 4.2.2. RX PHY Layer
4.2.1. RX Data Link Layer x
4.2.1.1. RX CGS 4.2.1.2. Frame Synchronization 4.2.1.3. Frame Alignment 4.2.1.4. Lane Alignment 4.2.1.5. ILAS Data 4.2.1.6. Initial Lane Synchronization
4.3. Operation x
4.3.1. Operating Modes 4.3.2. Scrambler/Descrambler 4.3.3. SYNC_N Signal 4.3.4. Link Reinitialization 4.3.5. Link Startup Sequence 4.3.6. Error Reporting Through SYNC_N Signal
4.3.1. Operating Modes x
4.3.1.1. Subclass 0 Operating Mode 4.3.1.2. Subclass 1 Operating Mode 4.3.1.3. Subclass 2 Operating Mode
4.4. Clocking Scheme x
4.4.1. Device Clock 4.4.2. Link Clock 4.4.3. Local MultiFrame Clock 4.4.4. Clock Correlation 4.4.5. System PLL Clock
4.5. Reset Scheme x
4.5.1. Reset Sequence 4.5.2. ADC–FPGA Subsystem Reset Sequence 4.5.3. FPGA–DAC Subsystem Reset Sequence
4.6. Signals x
4.6.1. Transmitter Signals 4.6.2. Receiver Signals
4.7. Registers x
4.7.1. Register Access Type Convention 4.7.2. Register Map and Definition 4.7.3. Transmitter Registers 4.7.4. Receiver Registers
5. F-Tile JESD204B IP Deterministic Latency Implementation Guidelines x
5.1. Constraining Incoming SYSREF Signal 5.2. Programmable RBD Offset 5.3. Programmable LMFC Offset 5.4. Maintaining Deterministic Latency during Link Reinitialization
6. F-Tile JESD204B IP Debug Guidelines x
6.1. Clocking Scheme 6.2. F-Tile JESD204B Parameters 6.3. SPI Programming 6.4. Converter and FPGA Operating Conditions 6.5. Signal Polarity and FPGA Pin Assignment
1. F-Tile JESD204B IP Quick Reference
2. About the F-Tile JESD204B Intel® FPGA IP
3. Getting Started
4. F-Tile JESD204B IP Functional Description
5. F-Tile JESD204B IP Deterministic Latency Implementation Guidelines
6. F-Tile JESD204B IP Debug Guidelines
7. F-Tile JESD204B Intel FPGA IP User Guide Archives
8. Document Revision History for the F-Tile JESD204B Intel® FPGA IP User Guide

4.2.1.5. ILAS Data

The F-Tile JESD204B RX IP core captures 14 octets of link configuration data that are transmitted on the 2nd multiframe of the ILAS phase. The receiver waits for the reception of /Q/ character that marks the start of link configuration data and then latch it into ILAS octets, which are per lane basis. You can read the 14 octets captured in the link configuration data through the CSR. You need to first set the csr_ilas_data_sel register to select which link configuration data lane it is trying to read from. Then, proceed to read from the csr_ilas_octet register.

Level Two Title