F-Tile 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP User Guide

Download PDF
ID 720989
Date 11/29/2023
Public
Document Table of Contents
Document Table of Contents x
1. About the F-Tile 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP User Guide 2. 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP Overview 3. Getting Started 4. Functional Description 5. 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP Parameters 6. Interface Signals 7. Configuration Registers 8. F-Tile 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP User Guide Archive 9. Document Revision History for the F-Tile 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP User Guide
2. 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP Overview x
2.1. Release Information 2.2. Features 2.3. Device Family Support 2.4. Device Speed Grade Support 2.5. Resource Utilization
3. Getting Started x
3.1. Introduction to Intel® FPGA IP 3.2. Installing and Licensing Intel® FPGA IPs 3.3. Specifying the IP Core Parameters and Options 3.4. Generated File Structure 3.5. Simulating Intel® FPGA IPs 3.6. Upgrading the 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP Core 3.7. Integrating Your IP Core in Your Design
3.2. Installing and Licensing Intel® FPGA IPs x
3.2.1. Intel® FPGA IP Evaluation Mode
3.7. Integrating Your IP Core in Your Design x
3.7.1. Adding the F-Tile Reference and System PLL IP
4. Functional Description x
4.1. Clocking and Reset Sequence 4.2. Timing Constraints 4.3. Operation Speed Switching 4.4. IEEE 802.3 Clause 37 Auto-Negotiation 4.5. USXGMII 4.6. IEEE 1588 Precision Time Protocol
4.1. Clocking and Reset Sequence x
4.1.1. Clocking 4.1.2. Reset
6. Interface Signals x
6.1. Clock Signals 6.2. Reset Signals 6.3. Serial Interface Signals 6.4. Avalon® Memory-Mapped Interface Signals 6.5. XGMII Signals 6.6. Transceiver Status and Transceiver Clock Status Signals 6.7. Reconfiguration Signals 6.8. Operating Speed and Status Signals
7. Configuration Registers x
7.1. Register Map 7.2. PHY Registers
1. About the F-Tile 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP User Guide
2. 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP Overview
3. Getting Started
4. Functional Description
5. 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP Parameters
6. Interface Signals
7. Configuration Registers
8. F-Tile 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP User Guide Archive
9. Document Revision History for the F-Tile 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP User Guide

6.4. Avalon® Memory-Mapped Interface Signals

The Avalon memory-mapped interface is an Avalon memory-mapped slave port. This interface uses word addressing and provides access to the 32-bit configuration registers of the PHY in PHY Registers. The following signals are synchronous to csr_clk.

Table 18.   Avalon® Memory-Mapped Interface Signals
Signal Name Direction Width Description
Avalon® Memory-Mapped CSR
csr_address Input 11 Use this bus to specify the register address to read from or write to.
csr_write Input 1 Assert this signal to request a write operation.
csr_read Input 1 Assert this signal to request a read operation.
csr_writedata Input 32 Data to be written to the specified register. The data is written only when the csr_waitrequest signal is deasserted.
csr_readdata Output 32 Data read from the specified register. The data is valid only when the csr_waitrequest signal is deasserted.
csr_waitrequest Output 1 When asserted, indicates that the PHY is busy and not ready to accept any read or write requests.
  • When you have requested for a read or write, keep the control signals to the Avalon® memory-mapped interface constant while this signal is asserted. The request is complete when it is deasserted.
  • This signal can be high or low during idle cycles and reset. Therefore, the user application must not make any assumption of its assertion state during these periods.
Level Two Title