eCPRI Intel® FPGA IP Design Example User Guide

Download PDF
ID 683837
Date 5/18/2024
Public
Document Table of Contents
Document Table of Contents x
1. Quick Start Guide 2. Design Example Description 3. eCPRI Intel® FPGA IP Design Example User Guide Archives 4. Document Revision History for eCPRI Intel® FPGA IP Design Example User Guide
1. Quick Start Guide x
1.1. Hardware and Software Requirements 1.2. Generating the Design 1.3. Directory Structure 1.4. Simulating the Design Example Testbench 1.5. Compiling the Compilation-Only Project 1.6. Compiling and Configuring the Design Example in Hardware 1.7. Testing the eCPRI Intel FPGA IP Design Example 1.8. Generating and Downloading the Executable and Linking Format (.elf) Programming File
1.4. Simulating the Design Example Testbench x
1.4.1. Enabling Dynamic Reconfiguration to the Ethernet IP
2. Design Example Description x
2.1. Features 2.2. eCPRI IP Hardware Design Example 2.3. Simulation Design Example 2.4. Interface Signals 2.5. Design Example Register Map
1. Quick Start Guide
2. Design Example Description
3. eCPRI Intel® FPGA IP Design Example User Guide Archives
4. Document Revision History for eCPRI Intel® FPGA IP Design Example User Guide

1.6. Compiling and Configuring the Design Example in Hardware

To compile the hardware design example and configure it on your Intel® device:

  1. Ensure hardware design example generation is complete.
  2. In the Quartus® Prime Pro Edition software, open the Quartus® Prime project <design_example_dir>/synthesis/quartus/ecpri_ed.qpf.
  3. On the Processing menu, click Start Compilation.
  4. After successful compilation, a .sof file is available in <design_example_dir>/synthesis/quartus/output_files directory. Follow these steps to program the hardware design example on the Intel® FPGA device:
    1. Connect Development Kit to the host computer.
    2. Launch the Clock Control application, which is part of the development kit, and set the new frequencies for the design example. Below is the frequency setting in the Clock Control application:
      • If you are targeting your design on Stratix® 10 GX SI Development Kit:
        • U5, OUT8- 100 MHz
        • U6, OUT3- 322.265625 MHz
        • U6, OUT4 and OUT5- 307.2 MHz
      • If you are targeting your design on Stratix® 10 TX SI Development Kit:
        • U1, CLK4- 322.265625 MHz (For 25G data rate)
        • U6- 156.25 MHz (For 10G data rate)
        • U3, OUT3- 100 MHz
        • U3, OUT8- 153.6 MHz
      • If you are targeting your design on Intel® Agilex™ 7 F-Series Transceiver-SoC Development Kit:
        • U37, CLK1A- 100 MHz
        • U34, CLK0P- 156.25 MHz
        • U38, OUT2_P- 153.6 MHz
      • If you are targeting your design on Arria® 10 GX SI Development Kit:
        • U52, CLK0- 156.25 MHz
        • U52, CLK1- 250 MHz
        • U52, CLK3- 125 MHz
        • Y5- 307.2 MHz
        • Y6- 322.265625 MHz
    3. On the Tools menu, click Programmer.
    4. In the Programmer, click Hardware Setup.
    5. Select a programming device.
    6. Select and add the Development Kit to which your Quartus® Prime Pro Edition session can connect.
    7. Ensure that Mode is set to JTAG.
    8. Select the device and click Add Device. The Programmer displays a block diagram of the connections between the devices on your board.
    9. Load the .sof file to your respective Intel® FPGA device.
    10. Load the Executable and Linking format (.elf) file to your Stratix® 10 or Intel® Agilex™ 7 device if you plan to perform the dynamic reconfiguration (DR) to switch the data rate between 25G and 10G.
    11. Generate the .elf file (refer to Generating and Downloading the Executable and Linking Format (.elf) File ).
    12. In the row with your .sof, check the Program/Configure box for the .sof file.
    13. Click Start.
Related Information
Level Two Title