Intel® MAX® 10 General Purpose I/O User Guide

Download PDF
ID 683751
Date 1/27/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Intel® MAX® 10 I/O Overview 2. Intel® MAX® 10 I/O Architecture and Features 3. Intel® MAX® 10 I/O Design Considerations 4. Intel® MAX® 10 I/O Implementation Guides 5. GPIO Lite Intel® FPGA IP References 6. Intel® MAX® 10 General Purpose I/O User Guide Archives 7. Document Revision History for Intel® MAX® 10 General Purpose I/O User Guide
1. Intel® MAX® 10 I/O Overview x
1.1. Intel® MAX® 10 Devices I/O Resources Per Package 1.2. Intel® MAX® 10 I/O Vertical Migration Support
2. Intel® MAX® 10 I/O Architecture and Features x
2.1. Intel® MAX® 10 I/O Standards Support 2.2. Intel® MAX® 10 I/O Elements 2.3. Intel® MAX® 10 I/O Buffers 2.4. I/O Standards Termination
2.1. Intel® MAX® 10 I/O Standards Support x
2.1.1. Intel® MAX® 10 I/O Standards Voltage and Pin Support
2.2. Intel® MAX® 10 I/O Elements x
2.2.1. Intel® MAX® 10 I/O Banks Architecture 2.2.2. Intel® MAX® 10 I/O Banks Performance 2.2.3. Intel® MAX® 10 I/O Banks Locations
2.3. Intel® MAX® 10 I/O Buffers x
2.3.1. Schmitt-Trigger Input Buffer 2.3.2. Programmable I/O Buffer Features
2.3.2. Programmable I/O Buffer Features x
2.3.2.1. Programmable Open Drain 2.3.2.2. Programmable Bus Hold 2.3.2.3. Programmable Pull-Up Resistor 2.3.2.4. Programmable Current Strength 2.3.2.5. Programmable Output Slew Rate Control 2.3.2.6. Programmable IOE Delay 2.3.2.7. PCI Clamp Diode 2.3.2.8. Programmable Pre-Emphasis 2.3.2.9. Programmable Differential Output Voltage 2.3.2.10. Programmable Emulated Differential Output 2.3.2.11. Programmable Dynamic Power Down
2.4. I/O Standards Termination x
2.4.1. Voltage-Referenced I/O Standards Termination 2.4.2. Differential I/O Standards Termination 2.4.3. Intel® MAX® 10 On-Chip I/O Termination
2.4.3. Intel® MAX® 10 On-Chip I/O Termination x
2.4.3.1. OCT Calibration 2.4.3.2. RS OCT in Intel® MAX® 10 Devices
3. Intel® MAX® 10 I/O Design Considerations x
3.1. Guidelines: VCCIO Range Considerations 3.2. Guidelines: Voltage-Referenced I/O Standards Restriction 3.3. Guidelines: Enable Clamp Diode for LVTTL/LVCMOS Input Buffers 3.4. Guidelines: Adhere to the LVDS I/O Restrictions Rules 3.5. Guidelines: I/O Restriction Rules 3.6. Guidelines: Placement Restrictions for 1.0 V I/O Pin 3.7. Guidelines: Analog-to-Digital Converter I/O Restriction 3.8. Guidelines: External Memory Interface I/O Restrictions 3.9. Guidelines: Dual-Purpose Configuration Pin 3.10. Guidelines: Clock and Data Input Signal for Intel® MAX® 10 E144 Package
3.6. Guidelines: Placement Restrictions for 1.0 V I/O Pin x
3.6.1. Calculating the Total Inductance for 1.0 V Pin Placement
4. Intel® MAX® 10 I/O Implementation Guides x
4.1. GPIO Lite Intel FPGA IP GPIO Lite Intel® FPGA IP 4.2. Verifying Pin Migration Compatibility
4.1. GPIO Lite Intel FPGA IP GPIO Lite Intel® FPGA IP x
4.1.1. GPIO Lite Intel® FPGA IP Data Paths
4.1.1. GPIO Lite Intel® FPGA IP Data Paths x
4.1.1.1. DDR Input Path 4.1.1.2. DDR Output Path with Output Enable
5. GPIO Lite Intel® FPGA IP References x
5.1. GPIO Lite Intel® FPGA IP Parameter Settings 5.2. GPIO Lite Intel® FPGA IP Interface Signals
1. Intel® MAX® 10 I/O Overview
2. Intel® MAX® 10 I/O Architecture and Features
3. Intel® MAX® 10 I/O Design Considerations
4. Intel® MAX® 10 I/O Implementation Guides
5. GPIO Lite Intel® FPGA IP References
6. Intel® MAX® 10 General Purpose I/O User Guide Archives
7. Document Revision History for Intel® MAX® 10 General Purpose I/O User Guide

3.9. Guidelines: Dual-Purpose Configuration Pin

To use configuration pins as user I/O pins in user mode, you have to adhere to the following guidelines.
Table 24.  Dual-Purpose Configuration Pin Guidelines for Intel® MAX® 10 Devices
Guidelines Pins
Configuration pins during initialization:
  • Tri-state the external I/O driver and drive an external pull-up resistor 13 or
  • Use the external I/O driver to drive the pins to the state same as the external weak pull-up resistor
  • nCONFIG
  • nSTATUS
  • CONF_DONE
JTAG pins:
  • If you intend to switch back and forth between user I/O pins and JTAG pin functions using the JTAGEN pin, all JTAG pins must be assigned as single-ended I/O pins or voltage-referenced I/O pins. Schmitt trigger input is the recommended input buffer.
  • JTAG pins cannot perform as JTAG pins in user mode if you assign any of the JTAG pin as a differential I/O pin.
  • You must use the JTAG pins as dedicated pins and not as user I/O pins during JTAG programming.
  • Do not toggle JTAG pin during the initialization stage.
  • Put the test access port (TAP) controller in reset state by driving the TDI and TMS pins high and toggle the TCK pin for at least 5 clock cycles before the initialization.
  • The Signal Tap logic analyzer IP, JTAG-to- Avalon® master bridge IP, and other JTAG-related IPs cannot be used if you enable the JTAG pin sharing feature in your design.
  • TDO
  • TMS
  • TCK
  • TDI
Attention: Assign all JTAG pins as single-ended I/O pins or voltage-referenced I/O pins if you enable JTAG pin sharing feature.
Related Information
13 If you intend to remove the external weak pull-up resistor, Intel recommends that you remove it after the device enters user mode.
Level Two Title