CPRI Intel® FPGA IP User Guide

Download PDF
ID 683595
Date 5/19/2023
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the CPRI Intel® FPGA IP Core 2. Getting Started with the CPRI Intel® FPGA IP Core 3. Functional Description 4. CPRI Intel® FPGA IP Core Signals 5. CPRI Intel® FPGA IP Core Registers 6. CPRI Intel® FPGA IP User Guide Archives 7. Document Revision History for the CPRI Intel® FPGA IP User Guide
1. About the CPRI Intel® FPGA IP Core x
1.1. CPRI Intel® FPGA IP Core Supported Features 1.2. CPRI Intel® FPGA IP Core Device Family and Speed Grade Support 1.3. Intel® FPGA IP Core Verification 1.4. Resource Utilization for CPRI Intel® FPGA IP Core 1.5. Release Information
1.2. CPRI Intel® FPGA IP Core Device Family and Speed Grade Support x
1.2.1. Device Family Support 1.2.2. CPRI Intel® FPGA IP Core Performance: Device and Transceiver Speed Grade Support
2. Getting Started with the CPRI Intel® FPGA IP Core x
2.1. Installation and Licensing 2.2. Generating CPRI Intel® FPGA IP Core 2.3. CPRI Intel® FPGA IP File Structure 2.4. CPRI Intel® FPGA IP Core Parameters 2.5. Integrating Your Intel® FPGA IP Core in Your Design: Required External Blocks 2.6. Simulating Intel FPGA IP Cores 2.7. Understanding the Testbench 2.8. Running the Design Example 2.9. Compiling the Full Design and Programming the FPGA
2.1. Installation and Licensing x
2.1.1. Intel® FPGA IP Evaluation Mode
2.5. Integrating Your Intel® FPGA IP Core in Your Design: Required External Blocks x
2.5.1. Adding the Transceiver TX PLL IP Core 2.5.2. System PLL Connections for the Intel Agilex® 7 F-tile Variations 2.5.3. Adding the Reset Controller 2.5.4. Adding the Transceiver Reconfiguration Controller 2.5.5. Adding the Off-Chip Clean-Up PLL 2.5.6. Adding and Connecting the Single-Trip Delay Calibration Blocks 2.5.7. Transceiver PLL Calibration 2.5.8. Reference and System PLL Clock for your IP Design
3. Functional Description x
3.1. Interfaces Overview 3.2. CPRI Intel® FPGA IP Core Clocking Structure 3.3. CPRI Intel® FPGA IP Core Reset Requirements 3.4. Start-Up Sequence Following Reset 3.5. AUX Interface 3.6. Direct IQ Interface 3.7. Ctrl_AxC Interface 3.8. Direct Vendor Specific Access Interface 3.9. Real-Time Vendor Specific Interface 3.10. Direct HDLC Serial Interface 3.11. Direct L1 Control and Status Interface 3.12. L1 Debug Interface 3.13. Media Independent Interface (MII) to External Ethernet Block 3.14. Gigabit Media Independent Interface (GMII) to External Ethernet Block 3.15. CPU Interface to CPRI Intel® FPGA IP Registers 3.16. Auto-Rate Negotiation 3.17. Extended Delay Measurement 3.18. Deterministic Latency and Delay Measurement and Calibration 3.19. CPRI Intel® FPGA IP Transceiver and Transceiver Management Interfaces 3.20. Testing Features
3.2. CPRI Intel® FPGA IP Core Clocking Structure x
3.2.1. Example CPRI Intel® FPGA IP Core Clock Connections in Different Clocking Modes
3.4. Start-Up Sequence Following Reset x
3.4.1. Start-Up Sequence Interface Signals
3.5. AUX Interface x
3.5.1. AUX Interface Signals 3.5.2. AUX Interface Synchronization 3.5.3. Auxiliary Latency Cycles 3.5.4. Direct Interface CPRI Frame Data Format
3.14. Gigabit Media Independent Interface (GMII) to External Ethernet Block x
3.14.1. GMII Normal Mode 3.14.2. Ethernet PCS Bypass Mode 3.14.3. Ethernet PCS Run-Time Switching
3.15. CPU Interface to CPRI Intel® FPGA IP Registers x
3.15.1. CPU Interface Signals 3.15.2. Accessing the Hyperframe Control Words
3.15.2. Accessing the Hyperframe Control Words x
3.15.2.1. Specifying the Control Word 3.15.2.2. Specifying the Position in the Control Word 3.15.2.3. Retrieving the Hyperframe Control Words 3.15.2.4. Writing the Hyperframe Control Words
3.17. Extended Delay Measurement x
3.17.1. Extended Delay Measurement for Soft Internal Buffers 3.17.2. Extended Delay Measurement for Intel® Stratix® 10 Hard FIFOs 3.17.3. Extended Delay Measurement Interface
3.18. Deterministic Latency and Delay Measurement and Calibration x
3.18.1. Delay Measurement and Calibration Features 3.18.2. Delay Requirements 3.18.3. Single-Hop Delay Measurement 3.18.4. Multi-Hop Delay Measurement 3.18.5. Delay Calibration Features
3.18.3. Single-Hop Delay Measurement x
3.18.3.1. Rx Path Delay 3.18.3.2. Tx Path Delay 3.18.3.3. Round-Trip Delay
3.18.5. Delay Calibration Features x
3.18.5.1. Single-Trip Delay Calibration 3.18.5.2. Round-Trip Delay Calibration 3.18.5.3. Tx Bitslip Delay
3.18.5.1. Single-Trip Delay Calibration x
3.18.5.1.1. Single-Trip Latency Measurement and Calibration Interface Signals
3.19. CPRI Intel® FPGA IP Transceiver and Transceiver Management Interfaces x
3.19.1. CPRI Link 3.19.2. Main Transceiver Clock and Reset Signals 3.19.3. Arria V, Arria V GZ, Cyclone V, and Stratix V Transceiver Reconfiguration Interface 3.19.4. Intel® Arria® 10, Intel® Stratix® 10, and Intel Agilex® 7 Transceiver Reconfiguration Interface 3.19.5. RS-FEC Interface 3.19.6. Interface to the External Reset Controller 3.19.7. Interface to the External PLL 3.19.8. Transceiver Debug Interface
3.20. Testing Features x
3.20.1. CPRI Intel® FPGA IP Core Loopback Modes 3.20.2. CPRI Intel® FPGA IP Core Self-Synchronization Feature
4. CPRI Intel® FPGA IP Core Signals x
4.1. CPRI Intel® FPGA IP Core L2 Interface 4.2. CPRI Intel® FPGA IP Core L1 Direct Access Interfaces 4.3. CPRI Intel® FPGA IP Core Management Interfaces 4.4. CPRI Intel® FPGA IP Core Transceiver and Transceiver Management Signals
1. About the CPRI Intel® FPGA IP Core
2. Getting Started with the CPRI Intel® FPGA IP Core
3. Functional Description
4. CPRI Intel® FPGA IP Core Signals
5. CPRI Intel® FPGA IP Core Registers
6. CPRI Intel® FPGA IP User Guide Archives
7. Document Revision History for the CPRI Intel® FPGA IP User Guide

2.2. Generating CPRI Intel® FPGA IP Core

You can configure a custom Intel® FPGA IP variation in the parameter editor. Use the following steps to specify CPRI IP core options and parameters in the parameter editor.
Figure 4. IP Parameter Editor
  1. In the Intel® Quartus® Prime Pro Edition software, click File > New Project Wizard to create a new Intel® Quartus® Prime project, or File > Open Project to open an existing Intel® Quartus® Prime project. The wizard prompts you to specify a device. In the Intel® Quartus® Prime Standard Edition software, this step is not required.
  2. In the Intel® FPGA IP Catalog (Tools > IP Catalog), locate and double-click the name CPRI Intel FPGA IP. The parameter editor appears.
  3. Specify a top-level name for your custom Intel® FPGA IP variation. The parameter editor saves the IP variation settings in a file named <your_ip> .ip (in Intel® Quartus® Prime Pro Edition) or <your_ip>.qsys (in Intel® Quartus® Prime Standard Edition). Click OK.
  4. Specify the parameters and options for your IP variation in the parameter editor, including one or more of the following. Refer to CPRI Intel FPGA IP Core Parameters for information about specific IP parameters.
    • Specify parameters defining the IP core functionality, port configurations, and device-specific features.
    • Specify options for processing the IP core files in other EDA tools.
  5. Click Generate HDL. The Generation dialog box appears.
  6. Specify output file generation options, and then click Generate. The IP variation files generate according to your specifications.
  7. To generate a simulation testbench, click Generate Example Design. Please refer to the instructions in the Running the Testbench section.
    Note: If you want to generate a design example with line bit rate auto-negotiation option (Enable line bit rate auto-negotiation), you must also select the option Enable Auto Rate Negotiation ED.
  8. To generate an HDL instantiation template that you can copy and paste into your text editor, click Generate > Show Instantiation Template.
  9. Click Finish. The parameter editor adds the top-level .qsys or .ip file to the current project automatically. If you are prompted to manually add the .qsys file to the project, click Project > Add/Remove Files in Project to add the file.
    For Intel Agilex® 7 F-tile devices, perform these additional steps:
    1. Copy the cpri_ii_tile_ip_gen.tcl from <your_ip>/altera_cpri_ii_c2p_top_<c2p version>/sim/ or <your_ip>/altera_cpri_ii_c2p_top_<c2p_version>/synth/ into the same level as <your_ip>.ip
    2. Execute this file using: 
      quartus_sh -t cpri_ii_tile_ip_gen.tcl <your_ip> skip_qtlg
    Few IP cores are generated along a top level wrapper. The wrapper intel_cpri_wrapper.v is the top level file for this IP. The systemclk_f_inst.ip, iopll_sclk_inst.ip, dr_ctrl_inst.ip (generated when rate negotiation is enabled), and cpriphy_ftile_0.ip are the generated IPs. You must add all these files manually to your Intel® Quartus® Prime project.
  10. After generating and instantiating your IP variation, make appropriate pin assignments to connect ports.
Level Two Title