AN 307: Intel® FPGA Design Flow for AMD* Xilinx* Users

Download PDF
ID 683562
Date 4/01/2024
Public
Document Table of Contents
Document Table of Contents x
1. Introduction to Intel® FPGA Design Flow for AMD* Xilinx* Users 2. Technology Comparison 3. FPGA Tools Comparison 4. AMD* Xilinx* to Intel® FPGA Design Conversion 5. Conclusion 6. AN 307: Intel® FPGA Design Flow for AMD* Xilinx* Users Archives 7. Document Revision History for Intel® FPGA Design Flow for AMD* Xilinx* Users
2. Technology Comparison x
2.1. Intel® FPGA and SoC Devices 2.2. Intel® - AMD* Xilinx* Device Comparison 2.3. Intel® FPGA Device Features
3. FPGA Tools Comparison x
3.1. Hardware and Software Tools for FPGA Design 3.2. FPGA Design Flow Using Command Line Scripting 3.3. FPGA Design Flow Using Tools with GUIs 3.4. Additional Quartus® Prime Pro Edition Features
3.2. FPGA Design Flow Using Command Line Scripting x
3.2.1. Command-Line Executable Equivalents 3.2.2. Programming and Configuration File Support in the Quartus® Prime Pro Edition Software
3.2.1. Command-Line Executable Equivalents x
3.2.1.1. synth_design 3.2.1.2. place_design/route_design 3.2.1.3. report_timing 3.2.1.4. write_bitstream 3.2.1.5. write_sdf/write_verilog/write_vhdl 3.2.1.6. report_power 3.2.1.7. write_checkpoint 3.2.1.8. Run Complete Design Flow
3.3. FPGA Design Flow Using Tools with GUIs x
3.3.1. Project Creation 3.3.2. Design Entry 3.3.3. IP Status 3.3.4. Design Constraints 3.3.5. Synthesis 3.3.6. Design Implementation 3.3.7. Finalize Pinout 3.3.8. Viewing and Editing Design Placement 3.3.9. Static Timing Analysis 3.3.10. Generation of Device Programming Files 3.3.11. Power Analysis 3.3.12. Simulation 3.3.13. Hardware Verification 3.3.14. View Netlist 3.3.15. Design Optimization 3.3.16. Techniques to Improve Productivity 3.3.17. Partial Reconfiguration 3.3.18. Cross-Probing in the Quartus® Prime Pro Edition Software
3.3.2. Design Entry x
3.3.2.1. HDL Editor 3.3.2.2. Schematic/Block Editor 3.3.2.3. State Machine Editor 3.3.2.4. IP Catalog and Parameter Editor 3.3.2.5. Platform Designer System Integration Tool 3.3.2.6. Platform Designer Component Editor
3.3.4. Design Constraints x
3.3.4.1. Assignment Editor 3.3.4.2. Create Timing Constraints with the Timing Analyzer GUI 3.3.4.3. Create Timing Constraints with the Timing Analyzer Text Editor
3.3.7. Finalize Pinout x
3.3.7.1. Pin Planner 3.3.7.2. Interface Planner 3.3.7.3. Tile Interface Planner
3.3.12. Simulation x
3.3.12.1. Simulation Models for Designs Containing LPMs or IP Cores
3.3.13. Hardware Verification x
3.3.13.1. System Console 3.3.13.2. Signal Tap Logic Analyzer 3.3.13.3. In-System Sources and Probes 3.3.13.4. Toolkit Explorer 3.3.13.5. Remote Debugging 3.3.13.6. Other Intel® FPGA Debugging Tools
3.3.13.4. Toolkit Explorer x
3.3.13.4.1. Transceiver Toolkit 3.3.13.4.2. EMIF Debug Toolkit
3.3.14. View Netlist x
3.3.14.1. RTL Viewer 3.3.14.2. Technology Map Viewer
3.3.15. Design Optimization x
3.3.15.1. Hyper-Aware Design Flow 3.3.15.2. Physical Synthesis Optimization 3.3.15.3. Optimization Modes 3.3.15.4. Fractal Synthesis
3.3.16. Techniques to Improve Productivity x
3.3.16.1. Fast Preservation 3.3.16.2. Engineering Change Order (ECO) Flow 3.3.16.3. Block-Based Design Flow 3.3.16.4. Design Assistant 3.3.16.5. Snapshot Viewer 3.3.16.6. Design Space Explorer II
3.4. Additional Quartus® Prime Pro Edition Features x
3.4.1. Scripting with Tcl in the Quartus® Prime Pro Edition Software
3.4.1. Scripting with Tcl in the Quartus® Prime Pro Edition Software x
3.4.1.1. Running Scripts from the DOS or UNIX Prompt 3.4.1.2. Running Scripts in Batch Mode from a Shell 3.4.1.3. Running Tcl Commands Directly from the Command Line 3.4.1.4. Running Tcl Commands Interactively from the Shell 3.4.1.5. The Quartus® Prime Tcl Console Window
4. AMD* Xilinx* to Intel® FPGA Design Conversion x
4.1. Replacing AMD* Xilinx* Primitives 4.2. Converting IP Cores 4.3. Setting Equivalent AMD* Xilinx* Design Constraints 4.4. Setting Up the Simulation Environment
4.1. Replacing AMD* Xilinx* Primitives x
4.1.1. Converting I/O Buffers 4.1.2. Changing Default I/O Standard for Pins 4.1.3. Converting Registers
4.1.1. Converting I/O Buffers x
4.1.1.1. Example of Converting I/O Buffer
4.2. Converting IP Cores x
4.2.1. Converting Memory Blocks 4.2.2. Converting Mixed-Mode Clock Manager (MMCM) to Phase-Locked Loop (PLL) 4.2.3. Converting Multipliers
4.2.1. Converting Memory Blocks x
4.2.1.1. Embedded Memory Blocks 4.2.1.2. Differences Between AMD* Xilinx* Memory and Intel® FPGA Memory 4.2.1.3. Determining Memory Block and Mapping Ports 4.2.1.4. Memory Port Mapping 4.2.1.5. Example: Converting Simple Dual-Port RAM
4.2.1.2. Differences Between AMD* Xilinx* Memory and Intel® FPGA Memory x
4.2.1.2.1. Memory Mode 4.2.1.2.2. Clocking Mode 4.2.1.2.3. Write and Read Operation Triggering 4.2.1.2.4. Read-During-Write Operation at the Same Address 4.2.1.2.5. Error Correction Code (ECC) 4.2.1.2.6. Byte Enable 4.2.1.2.7. Address Clock Enable 4.2.1.2.8. Parity Bit Support 4.2.1.2.9. Memory Initialization 4.2.1.2.10. Output Synchronous Set/Reset
4.2.2. Converting Mixed-Mode Clock Manager (MMCM) to Phase-Locked Loop (PLL) x
4.2.2.1. Feature Comparison 4.2.2.2. Port Mapping Reference 4.2.2.3. Example: Converting AMD* Xilinx* MMCM into an Intel® PLL
4.2.3. Converting Multipliers x
4.2.3.1. Feature Comparison 4.2.3.2. Port Mapping 4.2.3.3. Example: Converting to the LPM_MULT IP Core 4.2.3.4. Example: Converting to the Intel® FPGA Multiply Adder IP core
4.3. Setting Equivalent AMD* Xilinx* Design Constraints x
4.3.1. Device Constraints 4.3.2. Placement Constraints 4.3.3. Timing Constraints 4.3.4. Retimer Constraints
4.3.1. Device Constraints x
4.3.1.1. DRIVE 4.3.1.2. SLEW 4.3.1.3. IOB 4.3.1.4. IOSTANDARD 4.3.1.5. KEEP
4.3.2. Placement Constraints x
4.3.2.1. PBLOCK 4.3.2.2. PACKAGE_PIN 4.3.2.3. LOC & BEL 4.3.2.4. PROHIBIT
4.3.2.1. PBLOCK x
4.3.2.1.1. Differences Between PBLOCK and Logic Lock Regions
4.3.3. Timing Constraints x
4.3.3.1. Clock Domain Crossing
4.4. Setting Up the Simulation Environment x
4.4.1. Simulation Levels 4.4.2. HDL Support for EDA Simulators 4.4.3. Value Change Dump (VCD) Support 4.4.4. Simulating Intel FPGA IP Cores
1. Introduction to Intel® FPGA Design Flow for AMD* Xilinx* Users
2. Technology Comparison
3. FPGA Tools Comparison
4. AMD* Xilinx* to Intel® FPGA Design Conversion
5. Conclusion
6. AN 307: Intel® FPGA Design Flow for AMD* Xilinx* Users Archives
7. Document Revision History for Intel® FPGA Design Flow for AMD* Xilinx* Users

4.2.2.2. Port Mapping Reference

The following table shows the mapping between MMCM UltraScale* ports, created with the AMD* Xilinx* IP Catalog, and PLL ports in Stratix® 10 device, created with the IP Catalog.

Table 53.  Port-Mapping MMCM UltraScale* versus PLL Stratix® 10
AMD* Xilinx* MMCM Core Port Intel® FPGA Intel® FPGA IOPLL IP Core Port Description
clk_in1 refclk First clock input
clk_in2 refclk1 Second clock input
clkfb_in fbclk External clock feedback
clkfbout fboutclk Feeds into the feedback port
— activeclk Output signal that indicates which reference clock source the I/O PLL uses
clk_in_sel extswitch Switch between input clock ports
reset rst Asynchronous reset port
clk_out1, clk_out2, clk_outX outclk_[] Clock frequency output ports.

AMD* Xilinx* MMCM has fixed settings for most outputs, and you can configure the Intel® FPGA IOPLL IP core to suit them.

clkinstopped clkbad[1..0] Indicates whether the clock input signal stopped switching
clkfb_stopped — Specifies whether the feedback clock stopped
locked locked Specifies whether the PLL is locked
— adjpllin Input signal that feeds from upstream I/O PLL
— cascade_out Output signal that feeds into downstream I/O PLL
— zdbfbclk

Bidirectional port that connects to the mimic circuitry. You connect this port to a bidirectional pin that is placed on the positive feedback dedicated output pin of the I/O PLL.

The zdbfbclk port is available only if the I/O PLL is in zero-delay buffer mode.

AMD* Xilinx* MMCM Core Port Dynamic Phase Shift Ports in Intel® FPGA IOPLL Description
psclk scanclk Specifies clock that drives the dynamic phase shift operation
psen phase_en Start dynamic phase-shift operation
psincdec updn Specifies direction of phase shift operation
— cntsel Specifies counter for dynamic phase shift operation
— num_phase_shift Specifies number of phase shifts per dynamic phase shift operation
psdone phase_done Specifies completion of dynamic phase shift operation
power_down — Enables power_down input port for user selection

For more information about using dynamic PLL reconfiguration, refer to the Phase-Locked Loops ( Intel® FPGA IOPLL) IP Core User Guide.

Related Information
Level Two Title