Qsys System Design Tutorial

Download PDF
ID 683378
Date 5/04/2015
Public
Document Table of Contents
Document Table of Contents x
1. Qsys System Design Tutorial
1. Qsys System Design Tutorial x
1.1. Software and Hardware Requirements 1.2. Download and Install the Tutorial Design Files 1.3. Open the Tutorial Project 1.4. Creating Qsys Systems 1.5. Assemble a Hierarchical System 1.6. Viewing the Memory Tester System in Qsys 1.7. Compiling and Downloading Software to a Development Board 1.8. Debugging Your Design 1.9. Verifying Hardware in System Console 1.10. Simulating Custom Components 1.11. View a Diagram of the Completed System
1.4. Creating Qsys Systems x
1.4.1. Create a Data Pattern Generator Qsys System 1.4.2. Create a Data Pattern Checker Qsys System
1.4.1. Create a Data Pattern Generator Qsys System x
1.4.1.1. Create a New Qsys System and Set up the Clock Source 1.4.1.2. Add a Pipeline Bridge 1.4.1.3. Add a Custom Pattern Generator 1.4.1.4. Add a PRBS Pattern Generator 1.4.1.5. Add a Two-to-One Streaming Multiplexer 1.4.1.6. Verify the Memory Address Map 1.4.1.7. Connect the Reset Signals 1.4.1.8. Save the System
1.4.2. Create a Data Pattern Checker Qsys System x
1.4.2.1. Create a New Qsys System and Set Up the Clock Soource 1.4.2.2. Add a Pipeline Bridge 1.4.2.3. Add a Custom Pattern Checker 1.4.2.4. Add the PRBS Pattern Checker 1.4.2.5. Add a One-to-Two Streaming Demultiplexer 1.4.2.6. Verify the Memory Address Map 1.4.2.7. Connect the Reset Signals 1.4.2.8. Save the System
1.5. Assemble a Hierarchical System x
1.5.1. Create the Hierarchical Memory Tester System 1.5.2. Complete the Top-Level System
1.5.1. Create the Hierarchical Memory Tester System x
1.5.1.1. Add the Pattern Generator 1.5.1.2. Add the Pattern Checker 1.5.1.3. Add Memory Master Components 1.5.1.4. Connect the Reset Signals 1.5.1.5. Verify the Memory Address Map 1.5.1.6. Save the System
1.5.1.3. Add Memory Master Components x
1.5.1.3.1. Add a Pattern Writer Component 1.5.1.3.2. Add a Pattern Reader Component 1.5.1.3.3. Add a RAM Test Controller
1.9. Verifying Hardware in System Console x
1.9.1. Open the Tutorial Project 1.9.2. Add the JTAG-to-Avalon Master Bridge 1.9.3. Debug with System Console
1.10. Simulating Custom Components x
1.10.1. Generate a Testbench System in Qsys 1.10.2. Run Simulation In the ModelSim-Altera Software
1.10.1. Generate a Testbench System in Qsys x
1.10.1.1. Create a New Qsys System for the Design Under Test 1.10.1.2. Export Design Under Test 1.10.1.3. Generate a Testbench System 1.10.1.4. Generate Testbench System's Simulation Models
1.10.2. Run Simulation In the ModelSim-Altera Software x
1.10.2.1. Set Up the Simulation Environment 1.10.2.2. Run the Simulation
1. Qsys System Design Tutorial

1.4.1.6. Verify the Memory Address Map

You control the system by accessing the memory locations allocated to each component within the subsystem. To ensure that the memory map of the system you create matches the memory map of other components, you must verify the base addresses for the data pattern generator system.

On the Address Map tab, verify that the entries in the Address Map table match the values in #mwh1411073373020/table_54ED964DACCD4D7480A621FF0B0D0E00. Red exclamation marks indicate that the address ranges overlap. Correct the base addresses, as appropriate, to ensure there are no overlapping addresses, and your map matches this tutorial’s guidelines.

Table 1.  Address Map Table
Component Address
custom_pattern_generator.csr 0x00000400 – 0x0000040f
custom_pattern_generator.pattern_access 0x00000000 – 0x000003ff
prbs_pattern_generator.csr 0x00000420 – 0x0000043f
two_to_one_st_mux.csr 0x00000440 – 0x00000447
Level Two Title