Intel Agilex® 7 Embedded Memory User Guide

Download PDF
ID 683241
Date 6/26/2023
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Intel Agilex® 7 Embedded Memory Overview 2. Intel Agilex® 7 Embedded Memory Architecture and Features 3. Intel Agilex® 7 Embedded Memory Design Considerations 4. Intel Agilex® 7 Embedded Memory IP References 5. Intel Agilex® 7 Embedded Memory Debugging 6. Intel Agilex® 7 Embedded Memory User Guide Archives 7. Document Revision History for the Intel Agilex® 7 Embedded Memory User Guide
1. Intel Agilex® 7 Embedded Memory Overview x
1.1. Intel Agilex® 7 Embedded Memory Features
2. Intel Agilex® 7 Embedded Memory Architecture and Features x
2.1. Fabric Network-On-Chip (NoC) in Intel Agilex® 7 M-Series M20K Blocks 2.2. Byte Enable in Intel Agilex® 7 Embedded Memory Blocks 2.3. Address Clock Enable Support 2.4. Asynchronous Clear and Synchronous Clear 2.5. Memory Blocks Error Correction Code (ECC) Support 2.6. Intel Agilex® 7 Embedded Memory Clocking Modes 2.7. Intel Agilex® 7 Embedded Memory Configurations 2.8. Force-to-Zero 2.9. Coherent Read Memory 2.10. Freeze Logic 2.11. True Dual Port Dual Clock Emulator 2.12. Initial Value of Read and Write Address Registers 2.13. Timing/Power Optimization Feature in M20K Blocks 2.14. Intel Agilex® 7 Supported Embedded Memory IPs
2.2. Byte Enable in Intel Agilex® 7 Embedded Memory Blocks x
2.2.1. Byte Enable Controls 2.2.2. Data Byte Output 2.2.3. Byte Enable Behavior
2.5. Memory Blocks Error Correction Code (ECC) Support x
2.5.1. Parity Bit 2.5.2. ECC Parity Flip 2.5.3. ECC Read-During-Write Behavior 2.5.4. Error Correction Code Truth Table
2.6. Intel Agilex® 7 Embedded Memory Clocking Modes x
2.6.1. Single Clock Mode 2.6.2. Read/Write Clock Mode 2.6.3. Input/Output Clock Mode 2.6.4. Asynchronous/Synchronous Clears in Clocking Modes 2.6.5. Output Read Data in Simultaneous Read/Write 2.6.6. Independent Clock Enables in Clocking Modes
2.7. Intel Agilex® 7 Embedded Memory Configurations x
2.7.1. Mixed-Width Port Configurations
2.9. Coherent Read Memory x
2.9.1. Forwarding Logic
3. Intel Agilex® 7 Embedded Memory Design Considerations x
3.1. Consider the Memory Block Selection 3.2. Consider the Concurrent Read Behavior 3.3. Customize Read-During-Write Behavior 3.4. Consider Power-Up State and Memory Initialization 3.5. Reduce Power Consumption 3.6. Avoid Providing Non-Deterministic Input 3.7. Avoid Changing Clock Signals and Other Control Signals Simultaneously 3.8. Advanced Settings in Intel® Quartus® Prime Software for Memory 3.9. Consider the Memory Depth Setting 3.10. Consider Registering the Memory Output
3.3. Customize Read-During-Write Behavior x
3.3.1. Same-Port Read-During-Write Mode 3.3.2. Mixed-Port Read-During-Write Mode
4. Intel Agilex® 7 Embedded Memory IP References x
4.1. On Chip Memory RAM and ROM Intel® FPGA IP Cores 4.2. eSRAM Intel Agilex® FPGA IP 4.3. FIFO Intel® FPGA IP 4.4. Shift Register (RAM-based) Intel® FPGA IP
4.1. On Chip Memory RAM and ROM Intel® FPGA IP Cores x
4.1.1. Release Information for RAM and ROM Intel® FPGA IPs 4.1.2. RAM: 1-PORT Intel® FPGA IP Parameters 4.1.3. RAM: 2-PORT Intel® FPGA IP Parameters 4.1.4. RAM: 4-PORT Intel® FPGA IP Parameters 4.1.5. ROM: 1-PORT Intel® FPGA IP Parameters 4.1.6. ROM: 2-PORT Intel® FPGA IP Parameters 4.1.7. Changing Parameter Settings Manually 4.1.8. RAM and ROM Interface Signals
4.1.7. Changing Parameter Settings Manually x
4.1.7.1. RAM and ROM Parameter Settings
4.2. eSRAM Intel Agilex® FPGA IP x
4.2.1. Release Information for eSRAM Intel Agilex® FPGA IP 4.2.2. eSRAM System Features 4.2.3. eSRAM Intel Agilex® FPGA IP Parameters 4.2.4. eSRAM Intel Agilex® FPGA IP Interface Signals 4.2.5. eSRAM Timing Diagrams
4.2.2. eSRAM System Features x
4.2.2.1. eSRAM Specifications
4.3. FIFO Intel® FPGA IP x
4.3.1. Release Information for FIFO Intel® FPGA IP 4.3.2. Configuration Methods 4.3.3. Specifications 4.3.4. FIFO Functional Timing Requirements 4.3.5. SCFIFO ALMOST_EMPTY Functional Timing 4.3.6. FIFO Output Status Flag and Latency 4.3.7. FIFO Metastability Protection and Related Options 4.3.8. FIFO Synchronous Clear and Asynchronous Clear Effect 4.3.9. SCFIFO and DCFIFO Show-Ahead Mode 4.3.10. Different Input and Output Width 4.3.11. DCFIFO Timing Constraint Setting 4.3.12. Coding Example for Manual Instantiation 4.3.13. Design Example 4.3.14. Gray-Code Counter Transfer at the Clock Domain Crossing 4.3.15. Guidelines for Embedded Memory ECC Feature 4.3.16. FIFO Intel® FPGA IP Parameters 4.3.17. Reset Scheme
4.3.3. Specifications x
4.3.3.1. Verilog HDL Prototype 4.3.3.2. VHDL Component Declaration 4.3.3.3. VHDL LIBRARY-USE Declaration 4.3.3.4. HDL Code from Parameterizable Macros Template 4.3.3.5. FIFO Signals 4.3.3.6. FIFO Parameter Settings
4.3.8. FIFO Synchronous Clear and Asynchronous Clear Effect x
4.3.8.1. Recovery and Removal Timing Violation Warnings when Compiling a DCFIFO
4.3.11. DCFIFO Timing Constraint Setting x
4.3.11.1. Embedded Timing Constraint 4.3.11.2. User Configurable Timing Constraint
4.3.11.2. User Configurable Timing Constraint x
4.3.11.2.1. SDC Commands
4.4. Shift Register (RAM-based) Intel® FPGA IP x
4.4.1. Release Information for Shift Register (RAM-based) Intel® FPGA IP 4.4.2. Shift Register (RAM-based) Intel® FPGA IP Features 4.4.3. Shift Register (RAM-based) Intel® FPGA IP General Description 4.4.4. Shift Register (RAM-based) Intel® FPGA IP Parameter Settings 4.4.5. Shift Register Ports and Parameters Setting
1. Intel Agilex® 7 Embedded Memory Overview
2. Intel Agilex® 7 Embedded Memory Architecture and Features
3. Intel Agilex® 7 Embedded Memory Design Considerations
4. Intel Agilex® 7 Embedded Memory IP References
5. Intel Agilex® 7 Embedded Memory Debugging
6. Intel Agilex® 7 Embedded Memory User Guide Archives
7. Document Revision History for the Intel Agilex® 7 Embedded Memory User Guide

4.3.6. FIFO Output Status Flag and Latency

The main concern in most FIFO design is the output latency of the read and write status signals.
Table 42.  Output Latency of the Status Flags for SCFIFOThis table shows the output latency of the write signal (wrreq) and read signal (rdreq) for the SCFIFO according to the different output modes and optimization options.
Output Mode Optimization Option 18 Output Latency (in number of clock cycles)
Normal 19 Speed wrreq / rdreq to full: 1
wrreq to empty: 2
rdreq to empty: 1
wrreq / rdreq to usedw[]: 1
rdreq to q[]: 1
Area wrreq / rdreq to full: 1
wrreq / rdreq to empty : 1
wrreq / rdreq to usedw[] : 1
rdreq to q[]: 1
Show-ahead 19 Speed wrreq / rdreq to full: 1
wrreq to empty: 3
rdreq to empty: 1
wrreq / rdreq to usedw[]: 1
wrreq to q[]: 3
rdreq to q[]: 1
Area wrreq / rdreq to full: 1
wrreq to empty: 2
rdreq to empty: 1
wrreq / rdreq to usedw[]: 1
wrreq to q[]: 2
rdreq to q[]: 1
Table 43.  ALM Implemented RAM Mode for SCFIFO and DCFIFO
Output Mode Optimization Option 20 Output Latency (in number of clock cycles)
Normal 21 Speed wrreq / rdreq to full: 1
wrreq to empty: 1
rdreq to empty: 1
wrreq / rdreq to usedw[]: 1
rdreq to q[]: 1
Area wrreq / rdreq to full: 1
wrreq / rdreq to empty : 1
wrreq / rdreq to usedw[] : 1
rdreq to q[]: 1
Show-ahead 21 Speed wrreq / rdreq to full: 1
wrreq to empty: 1
rdreq to empty: 1
wrreq / rdreq to usedw[]: 1
wrreq to q[]: 1
rdreq to q[]: 1
Area wrreq / rdreq to full: 1
wrreq to empty: 1
rdreq to empty: 1
wrreq / rdreq to usedw[]: 1
wrreq to q[]: 1
rdreq to q[]: 1
Table 44.  Output Latency of the Status Flag for the DCFIFO This table shows the output latency of the write signal (wrreq) and read signal (rdreq) for the DCFIFO.
Output Latency (in number of clock cycles)
wrreq to wrfull: 1 wrclk
wrreq to rdfull: 2 wrclk cycles + following n rdclk 22
wrreq to wrempty: 1 wrclk
wrreq to rdempty: 2 wrclk 23 + following n rdclk 23
wrreq to wrusedw[]: 2 wrclk
wrreq to rdusedw[]: 2 wrclk + following n + 1 rdclk 23
wrreq to q[]: 1 wrclk + following 1 rdclk 23
rdreq to rdempty: 1 rdclk
rdreq to wrempty: 1 rdclk + following n wrclk 23
rdreq to rfull: 1 rdclk
rdreq to wrfull: 1 rdclk + following n wrclk 23
rdreq to rdusedw[]: 2 rdclk
rdreq to wrusedw[]: 1 rdclk + following n + 1 wrclk 23
rdreq to q[]: 1 rdclk
18 Speed optimization is equivalent to setting the ADD_RAM_OUTPUT_REGISTER parameter to ON. Setting the parameter to OFF is equivalent to area optimization.
19 Normal output mode is equivalent to setting the LPM_SHOWAHEAD parameter to OFF. For Show-ahead mode, the parameter is set to ON.
20 Speed optimization is equivalent to setting the ADD_RAM_OUTPUT_REGISTER parameter to ON. Setting the parameter to OFF is equivalent to area optimization.
21 Normal output mode is equivalent to setting the LPM_SHOWAHEAD parameter to OFF. For Show-ahead mode, the parameter is set to ON.
22 The number of n cycles for rdclk and wrclk is equivalent to the number of synchronization stages and are related to the WRSYNC_DELAYPIPE and RDSYNC_DELAYPIPE parameters. For more information about how the actual synchronization stage (n) is related to the parameters set for different target device, refer to FIFO Metastability Protection and Related Options .
23 This is applied only to Show-ahead output modes. Show-ahead output mode is equivalent to setting the LPM_SHOWAHEAD parameter to ON.
Level Two Title