F-Tile Low Latency 50G Ethernet Intel® FPGA IP User Guide

Download PDF
ID 758946
Date 1/09/2024
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the F-Tile Low Latency 50G Ethernet Intel® FPGA IP User Guide 2. About this IP 3. Getting Started 4. F-Tile Low Latency 50G Ethernet Intel® FPGA IP Parameters 5. Functional Description 6. Reset 7. Interfaces and Signal Descriptions 8. Control, Status, and Statistics Register Descriptions 9. Document Revision History for the F-Tile Low Latency 50G Ethernet Intel® FPGA IP User Guide
2. About this IP x
2.1. Release Information 2.2. Features 2.3. Device Family Support 2.4. Performance and Resource Utilization
3. Getting Started x
3.1. Installing and Licensing Intel® FPGA IP Cores 3.2. Specifying the IP Core Parameters and Options 3.3. Simulating the IP Core 3.4. Generated File Structure 3.5. Integrating Your IP Core in Your Design 3.6. Compiling the Full Design and Programming the FPGA
3.1. Installing and Licensing Intel® FPGA IP Cores x
3.1.1. Intel® FPGA IP Evaluation Mode
3.5. Integrating Your IP Core in Your Design x
3.5.1. Pin Assignments 3.5.2. Adding the F-Tile Reference and System PLL Clocks Intel® FPGA IP 3.5.3. Placement Settings for the 50G Ethernet Intel FPGA IP Core
5. Functional Description x
5.1. F-Tile Low Latency 50G Ethernet Intel® FPGA IP Functional Description 5.2. User Interface to Ethernet Transmission
5.1. F-Tile Low Latency 50G Ethernet Intel® FPGA IP Functional Description x
5.1.1. F-Tile Low Latency 50G Ethernet Intel® FPGA IP TX MAC Datapath 5.1.2. 50 GbE TX PCS 5.1.3. F-Tile Low Latency 50G Ethernet Intel® FPGA IP Core RX MAC Datapath 5.1.4. Link Fault Signaling Interface 5.1.5. 50 GbE RX PCS 5.1.6. Flow Control
5.1.1. F-Tile Low Latency 50G Ethernet Intel® FPGA IP TX MAC Datapath x
5.1.1.1. Frame Padding 5.1.1.2. Preamble Insertion 5.1.1.3. Inter-Packet Gap Generation and Insertion 5.1.1.4. Frame Check Sequence (CRC32) Insertion
5.1.3. F-Tile Low Latency 50G Ethernet Intel® FPGA IP Core RX MAC Datapath x
5.1.3.1. IP Core Preamble Processing 5.1.3.2. IP Core Malformed Packet Handling 5.1.3.3. Length/Type Field Processing
5.1.3.3. Length/Type Field Processing x
5.1.3.3.1. Length Checking 5.1.3.3.2. RX CRC Checking and Dynamic Forwarding
5.1.6. Flow Control x
5.1.6.1. TX Pause/PFC Flow Control Frame Transmission Request 5.1.6.2. XON/XOFF Pause Frames
5.2. User Interface to Ethernet Transmission x
5.2.1. Order of Transmission 5.2.2. Bit Order For TX and RX Datapaths
7. Interfaces and Signal Descriptions x
7.1. TX MAC Interface to User Logic 7.2. RX MAC Interface to User Logic 7.3. Transceivers 7.4. Transceiver Reconfiguration Signals 7.5. Avalon® Memory-Mapped Management Interface 7.6. Miscellaneous Status and Debug Signals 7.7. Flow Control Signals 7.8. Clock Signals 7.9. Reset Signals
8. Control, Status, and Statistics Register Descriptions x
8.1. TX MAC Registers 8.2. RX MAC Registers 8.3. Pause/PFC Flow Control Registers 8.4. Statistics Registers 8.5. Hard IP Registers
8.4. Statistics Registers x
8.4.1. Statistics Registers
1. About the F-Tile Low Latency 50G Ethernet Intel® FPGA IP User Guide
2. About this IP
3. Getting Started
4. F-Tile Low Latency 50G Ethernet Intel® FPGA IP Parameters
5. Functional Description
6. Reset
7. Interfaces and Signal Descriptions
8. Control, Status, and Statistics Register Descriptions
9. Document Revision History for the F-Tile Low Latency 50G Ethernet Intel® FPGA IP User Guide

3.2. Specifying the IP Core Parameters and Options

The F-Tile Low Latency 50G Ethernet Intel® FPGA IP parameter editor allows you to quickly configure your custom IP variation. Use the following steps to specify IP core options and parameters in the Intel® Quartus® Prime Pro Edition software.
  1. In the Intel® Quartus® Prime Pro Edition, click File > New Project Wizard to create a new Quartus Prime project, or File > Open Project to open an existing Quartus Prime project. The wizard prompts you to specify a device.
  2. In the IP Catalog (Tools > IP Catalog), locate and double-click the name of the IP core to customize. The New IP Variation window appears.
  3. In the New IP Variation dialog box, specify a top-level name for your custom IP variation. The parameter editor saves the IP variation settings in a file named <your_ip> .ip.
  4. Click Create. The parameter editor appears.
  5. On the IP tab, specify the parameters for your IP core variation. Refer to F-Tile Low Latency 50G Ethernet Intel® FPGA IP Parameters for information about specific IP core parameters.
  6. Click Generate HDL. The Generation dialog box appears.
  7. Specify output file generation options, and then click Generate. The IP variation files generate according to your specifications.
  8. Click Finish. The parameter editor adds the top-level .ip file to the current project automatically. If you are prompted to manually add the .ip file to the project, click Project > Add/Remove Files in Project to add the file.
  9. After generating and instantiating your IP variation, make appropriate pin assignments to connect ports.
Related Information
Level Two Title