Arria V GZ Avalon-MM Interface for PCIe Solutions: User Guide

Download PDF
ID 723696
Date 5/21/2017
Public
Document Table of Contents
Document Table of Contents x
1. Datasheet 2. Getting Started with the Avalon-MM Design Example 3. Parameter Settings 4. 64- or 128-Bit Avalon-MM Interface to the Endpoint Application Layer 5. Registers 6. Interrupts for Endpoints 7. Error Handling A. PCI Express Protocol Stack 8. Transceiver PHY IP Reconfiguration 9. Design Implementation 10. Throughput Optimization 11. Additional Features 12. Debugging B. Lane Initialization and Reversal C. Document Revision History
1. Datasheet x
1.1. Arria® V GZ Avalon-MM Interface for PCIe Datasheet 1.2. Features 1.3. Release Information 1.4. Device Family Support 1.5. Configurations 1.6. Design Examples 1.7. IP Core Verification 1.8. Resource Utilization 1.9. Recommended Speed Grades 1.10. Creating a Design for PCI Express
1.7. IP Core Verification x
1.7.1. Compatibility Testing Environment
2. Getting Started with the Avalon-MM Design Example x
2.1. Running Qsys 2.2. Generating the Example Design 2.3. Understanding Simulation Log File Generation 2.4. Running a Gate-Level Simulation 2.5. Simulating the Single DWord Design 2.6. Generating Synthesis Files 2.7. Creating a Quartus® Prime Project 2.8. Compiling the Design 2.9. Programming a Device 2.10. Understanding Channel Placement Guidelines
3. Parameter Settings x
3.1. System Settings 3.2. Base Address Register (BAR) Settings 3.3. Device Identification Registers 3.4. PCI Express and PCI Capabilities Parameters 3.5. Avalon Memory‑Mapped System Settings
3.4. PCI Express and PCI Capabilities Parameters x
3.4.1. Device Capabilities 3.4.2. Error Reporting 3.4.3. Link Capabilities 3.4.4. MSI and MSI-X Capabilities 3.4.5. Power Management
4. 64- or 128-Bit Avalon-MM Interface to the Endpoint Application Layer x
4.1. 32-Bit Non-Bursting Avalon-MM Control Register Access (CRA) Slave Signals 4.2. Bursting and Non-Bursting Avalon® -MM Module Signals 4.3. 64- or 128-Bit Bursting TX Avalon-MM Slave Signals 4.4. Clock Signals 4.5. Reset 4.6. Interrupts for Endpoints when Multiple MSI/MSI-X Support Is Enabled 4.7. Hard IP Status Signals 4.8. Physical Layer Interface Signals
4.7. Hard IP Status Signals x
4.7.1. Hard IP Reconfiguration Interface
4.8. Physical Layer Interface Signals x
4.8.1. Hard IP Status Extension 4.8.2. Serial Data Signals 4.8.3. PIPE Interface Signals 4.8.4. Test Signals
4.8.2. Serial Data Signals x
4.8.2.1. Physical Layout of Hard IP in Arria V GZ Devices 4.8.2.2. Channel Placement in Arria V GZ and Stratix V GX/GT/GS Devices
5. Registers x
5.1. Correspondence between Configuration Space Registers and the PCIe Specification 5.2. Type 0 Configuration Space Registers 5.3. Type 1 Configuration Space Registers 5.4. PCI Express Capability Structures 5.5. Intel-Defined VSEC Registers 5.6. CvP Registers 5.7. 64- or 128-Bit Avalon-MM Bridge Register Descriptions 5.8. Programming Model for Avalon-MM Root Port 5.9. Uncorrectable Internal Error Mask Register 5.10. Uncorrectable Internal Error Status Register 5.11. Correctable Internal Error Mask Register 5.12. Correctable Internal Error Status Register
5.7. 64- or 128-Bit Avalon-MM Bridge Register Descriptions x
5.7.1. Avalon-MM to PCI Express Interrupt Registers
5.7.1. Avalon-MM to PCI Express Interrupt Registers x
5.7.1.1. Avalon-MM to PCI Express Interrupt Status Registers 5.7.1.2. Avalon-MM to PCI Express Interrupt Enable Registers 5.7.1.3. PCI Express Mailbox Registers 5.7.1.4. Avalon-MM-to-PCI Express Address Translation Table 5.7.1.5. PCI Express to Avalon-MM Interrupt Status and Enable Registers for Endpoints 5.7.1.6. Avalon-MM Mailbox Registers 5.7.1.7. Control Register Access (CRA) Avalon-MM Slave Port
5.8. Programming Model for Avalon-MM Root Port x
5.8.1. Sending a Write TLP 5.8.2. Sending a Read TLP or Receiving a Non-Posted Completion TLP 5.8.3. Examples of Reading and Writing BAR0 Using the CRA Interface 5.8.4. PCI Express to Avalon-MM Interrupt Status and Enable Registers for Root Ports 5.8.5. Root Port TLP Data Registers
6. Interrupts for Endpoints x
6.1. Enabling MSI or Legacy Interrupts 6.2. Generation of Avalon-MM Interrupts 6.3. Interrupts for Endpoints Using the Avalon-MM Interface with Multiple MSI/MSI-X Support
7. Error Handling x
7.1. Physical Layer Errors 7.2. Data Link Layer Errors 7.3. Transaction Layer Errors 7.4. Error Reporting and Data Poisoning 7.5. Uncorrectable and Correctable Error Status Bits
A. PCI Express Protocol Stack x
A.1. Top-Level Interfaces A.2. Data Link Layer A.3. Physical Layer A.4. 32-Bit PCI Express Avalon-MM Bridge A.5. Completer Only Single Dword Endpoint
A.1. Top-Level Interfaces x
A.1.1. Avalon-MM Interface A.1.2. Clocks and Reset A.1.3. Transceiver Reconfiguration A.1.4. Interrupts A.1.5. PIPE
A.4. 32-Bit PCI Express Avalon-MM Bridge x
A.4.1. Avalon‑MM Bridge TLPs A.4.2. Avalon-MM-to-PCI Express Write Requests A.4.3. Avalon-MM-to-PCI Express Upstream Read Requests A.4.4. PCI Express-to-Avalon-MM Read Completions A.4.5. PCI Express-to-Avalon-MM Downstream Write Requests A.4.6. PCI Express-to-Avalon-MM Downstream Read Requests A.4.7. Avalon-MM-to-PCI Express Read Completions A.4.8. PCI Express-to-Avalon-MM Address Translation for 32-Bit Bridge A.4.9. Minimizing BAR Sizes and the PCIe Address Space A.4.10. Avalon® -MM-to-PCI Express Address Translation Algorithm for 32-Bit Addressing
A.5. Completer Only Single Dword Endpoint x
A.5.1. RX Block A.5.2. Avalon-MM RX Master Block A.5.3. TX Block A.5.4. Interrupt Handler Block
8. Transceiver PHY IP Reconfiguration x
8.1. Connecting the Transceiver Reconfiguration Controller IP Core 8.2. Transceiver Reconfiguration Controller Connectivity for Designs Using CvP
9. Design Implementation x
9.1. Making Analog QSF Assignments Using the Assignment Editor 9.2. Making Pin Assignments to Assign I/O Standard to Serial Data Pins 9.3. Recommended Reset Sequence to Avoid Link Training Issues 9.4. SDC Timing Constraints
10. Throughput Optimization x
10.1. Throughput of Posted Writes 10.2. Throughput of Non-Posted Reads
11. Additional Features x
11.1. Configuration over Protocol (CvP) 11.2. Autonomous Mode 11.3. ECRC
11.2. Autonomous Mode x
11.2.1. Enabling Autonomous Mode 11.2.2. Enabling CvP Initialization
11.3. ECRC x
11.3.1. ECRC on the RX Path 11.3.2. ECRC on the TX Path
12. Debugging x
12.1. Hardware Bring-Up Issues 12.2. Link Training 12.3. Use Third-Party PCIe Analyzer 12.4. BIOS Enumeration Issues
12.2. Link Training x
12.2.1. Debugging Link that Fails To Reach L0
C. Document Revision History x
C.1. Cyclone® V Avalon® Memory Mapped (Avalon-MM) Interface for PCIe* Solutions User Guide Revision History
1. Datasheet
2. Getting Started with the Avalon-MM Design Example
3. Parameter Settings
4. 64- or 128-Bit Avalon-MM Interface to the Endpoint Application Layer
5. Registers
6. Interrupts for Endpoints
7. Error Handling
A. PCI Express Protocol Stack
8. Transceiver PHY IP Reconfiguration
9. Design Implementation
10. Throughput Optimization
11. Additional Features
12. Debugging
B. Lane Initialization and Reversal
C. Document Revision History

A.4.10. Avalon® -MM-to-PCI Express Address Translation Algorithm for 32-Bit Addressing

Note: The PCI Express-to-Avalon-MM bridge supports both 32- and 64-bit addresses. If you select 64-bit addressing the bridge does not perform address translation.

When you specify 32-bit addresses, the Avalon-MM address of a received request on the TX Avalon‑MM slave port is translated to the PCI Express address before the request packet is sent to the Transaction Layer. You can specify up to 512 address pages and sizes ranging from 4 KB to 4 GB when you customize your Avalon‑MM Arria® V GZ Hard IP for PCI Express as described in Avalon to PCIe Address Translation Settings . This address translation process proceeds by replacing the MSB of the Avalon‑MM address with the value from a specific translation table entry; the LSB remains unchanged. The number of MSBs to be replaced is calculated based on the total address space of the upstream PCI Express devices that the Avalon‑MM Hard IP for PCI Express can access. The number of MSB bits is defined by the difference between the maximum number of bits required to represent the address space supported by the upstream PCI Express device minus the number of bits required to represent the Size of address pages which are the LSB pass-through bits (N). The Size of address pages (N) is applied to all entries in the translation table.

Each of the 512 possible entries corresponds to the base address of a PCI Express memory segment of a specific size. The segment size of each entry must be identical. The total size of all the memory segments is used to determine the number of address MSB to be replaced. In addition, each entry has a 2-bit field, Sp[1:0], that specifies 32-bit or 64-bit PCI Express addressing for the translated address. The most significant bits of the Avalon-MM address are used by the interconnect fabric to select the slave port and are not available to the slave. The next most significant bits of the Avalon-MM address index the address translation entry to be used for the translation process of MSB replacement.

For example, if the core is configured with an address translation table with the following attributes:

  • Number of Address Pages—16
  • Size of Address Pages—1 MB
  • PCI Express Address Size—64 bits

then the values in the following figure are:

  • N = 20 (due to the 1 MB page size)
  • Q = 16 (number of pages)
  • M = 24 (20 + 4 bit page selection)
  • P = 64

In this case, the Avalon address is interpreted as follows:

  • Bits [31:24] select the TX slave module port from among other slaves connected to the same master by the system interconnect fabric. The decode is based on the base addresses assigned in Platform Designer.
  • Bits [23:20] select the address translation table entry.
  • Bits [63:20] of the address translation table entry become PCI Express address bits [63:20].
  • Bits [19:0] are passed through and become PCI Express address bits [19:0].

The address translation table is dynamically configured at run time. The address translation table is implemented in memory and can be accessed through the CRA slave module. Dynamic configuration is optimal in a typical PCI Express system where address allocation occurs after BIOS initialization.

Figure 40. Avalon-MM-to-PCI Express Address Translation
The following figure depicts the Avalon-MM-to-PCI Express address translation process. In this figure the variables represent the following parameters:
  • N—the number of pass-through bits.
  • M—the number of Avalon-MM address bits.
  • P—the number of PCIe address bits.
  • Q—the number of translation table entries.
  • Sp[1:0]—the space indication for each entry.
Level Two Title