Arria V GZ Avalon-MM Interface for PCIe Solutions: User Guide

Download PDF
ID 723696
Date 5/21/2017
Public
Document Table of Contents
Document Table of Contents x
1. Datasheet 2. Getting Started with the Avalon-MM Design Example 3. Parameter Settings 4. 64- or 128-Bit Avalon-MM Interface to the Endpoint Application Layer 5. Registers 6. Interrupts for Endpoints 7. Error Handling A. PCI Express Protocol Stack 8. Transceiver PHY IP Reconfiguration 9. Design Implementation 10. Throughput Optimization 11. Additional Features 12. Debugging B. Lane Initialization and Reversal C. Document Revision History
1. Datasheet x
1.1. Arria® V GZ Avalon-MM Interface for PCIe Datasheet 1.2. Features 1.3. Release Information 1.4. Device Family Support 1.5. Configurations 1.6. Design Examples 1.7. IP Core Verification 1.8. Resource Utilization 1.9. Recommended Speed Grades 1.10. Creating a Design for PCI Express
1.7. IP Core Verification x
1.7.1. Compatibility Testing Environment
2. Getting Started with the Avalon-MM Design Example x
2.1. Running Qsys 2.2. Generating the Example Design 2.3. Understanding Simulation Log File Generation 2.4. Running a Gate-Level Simulation 2.5. Simulating the Single DWord Design 2.6. Generating Synthesis Files 2.7. Creating a Quartus® Prime Project 2.8. Compiling the Design 2.9. Programming a Device 2.10. Understanding Channel Placement Guidelines
3. Parameter Settings x
3.1. System Settings 3.2. Base Address Register (BAR) Settings 3.3. Device Identification Registers 3.4. PCI Express and PCI Capabilities Parameters 3.5. Avalon Memory‑Mapped System Settings
3.4. PCI Express and PCI Capabilities Parameters x
3.4.1. Device Capabilities 3.4.2. Error Reporting 3.4.3. Link Capabilities 3.4.4. MSI and MSI-X Capabilities 3.4.5. Power Management
4. 64- or 128-Bit Avalon-MM Interface to the Endpoint Application Layer x
4.1. 32-Bit Non-Bursting Avalon-MM Control Register Access (CRA) Slave Signals 4.2. Bursting and Non-Bursting Avalon® -MM Module Signals 4.3. 64- or 128-Bit Bursting TX Avalon-MM Slave Signals 4.4. Clock Signals 4.5. Reset 4.6. Interrupts for Endpoints when Multiple MSI/MSI-X Support Is Enabled 4.7. Hard IP Status Signals 4.8. Physical Layer Interface Signals
4.7. Hard IP Status Signals x
4.7.1. Hard IP Reconfiguration Interface
4.8. Physical Layer Interface Signals x
4.8.1. Hard IP Status Extension 4.8.2. Serial Data Signals 4.8.3. PIPE Interface Signals 4.8.4. Test Signals
4.8.2. Serial Data Signals x
4.8.2.1. Physical Layout of Hard IP in Arria V GZ Devices 4.8.2.2. Channel Placement in Arria V GZ and Stratix V GX/GT/GS Devices
5. Registers x
5.1. Correspondence between Configuration Space Registers and the PCIe Specification 5.2. Type 0 Configuration Space Registers 5.3. Type 1 Configuration Space Registers 5.4. PCI Express Capability Structures 5.5. Intel-Defined VSEC Registers 5.6. CvP Registers 5.7. 64- or 128-Bit Avalon-MM Bridge Register Descriptions 5.8. Programming Model for Avalon-MM Root Port 5.9. Uncorrectable Internal Error Mask Register 5.10. Uncorrectable Internal Error Status Register 5.11. Correctable Internal Error Mask Register 5.12. Correctable Internal Error Status Register
5.7. 64- or 128-Bit Avalon-MM Bridge Register Descriptions x
5.7.1. Avalon-MM to PCI Express Interrupt Registers
5.7.1. Avalon-MM to PCI Express Interrupt Registers x
5.7.1.1. Avalon-MM to PCI Express Interrupt Status Registers 5.7.1.2. Avalon-MM to PCI Express Interrupt Enable Registers 5.7.1.3. PCI Express Mailbox Registers 5.7.1.4. Avalon-MM-to-PCI Express Address Translation Table 5.7.1.5. PCI Express to Avalon-MM Interrupt Status and Enable Registers for Endpoints 5.7.1.6. Avalon-MM Mailbox Registers 5.7.1.7. Control Register Access (CRA) Avalon-MM Slave Port
5.8. Programming Model for Avalon-MM Root Port x
5.8.1. Sending a Write TLP 5.8.2. Sending a Read TLP or Receiving a Non-Posted Completion TLP 5.8.3. Examples of Reading and Writing BAR0 Using the CRA Interface 5.8.4. PCI Express to Avalon-MM Interrupt Status and Enable Registers for Root Ports 5.8.5. Root Port TLP Data Registers
6. Interrupts for Endpoints x
6.1. Enabling MSI or Legacy Interrupts 6.2. Generation of Avalon-MM Interrupts 6.3. Interrupts for Endpoints Using the Avalon-MM Interface with Multiple MSI/MSI-X Support
7. Error Handling x
7.1. Physical Layer Errors 7.2. Data Link Layer Errors 7.3. Transaction Layer Errors 7.4. Error Reporting and Data Poisoning 7.5. Uncorrectable and Correctable Error Status Bits
A. PCI Express Protocol Stack x
A.1. Top-Level Interfaces A.2. Data Link Layer A.3. Physical Layer A.4. 32-Bit PCI Express Avalon-MM Bridge A.5. Completer Only Single Dword Endpoint
A.1. Top-Level Interfaces x
A.1.1. Avalon-MM Interface A.1.2. Clocks and Reset A.1.3. Transceiver Reconfiguration A.1.4. Interrupts A.1.5. PIPE
A.4. 32-Bit PCI Express Avalon-MM Bridge x
A.4.1. Avalon‑MM Bridge TLPs A.4.2. Avalon-MM-to-PCI Express Write Requests A.4.3. Avalon-MM-to-PCI Express Upstream Read Requests A.4.4. PCI Express-to-Avalon-MM Read Completions A.4.5. PCI Express-to-Avalon-MM Downstream Write Requests A.4.6. PCI Express-to-Avalon-MM Downstream Read Requests A.4.7. Avalon-MM-to-PCI Express Read Completions A.4.8. PCI Express-to-Avalon-MM Address Translation for 32-Bit Bridge A.4.9. Minimizing BAR Sizes and the PCIe Address Space A.4.10. Avalon® -MM-to-PCI Express Address Translation Algorithm for 32-Bit Addressing
A.5. Completer Only Single Dword Endpoint x
A.5.1. RX Block A.5.2. Avalon-MM RX Master Block A.5.3. TX Block A.5.4. Interrupt Handler Block
8. Transceiver PHY IP Reconfiguration x
8.1. Connecting the Transceiver Reconfiguration Controller IP Core 8.2. Transceiver Reconfiguration Controller Connectivity for Designs Using CvP
9. Design Implementation x
9.1. Making Analog QSF Assignments Using the Assignment Editor 9.2. Making Pin Assignments to Assign I/O Standard to Serial Data Pins 9.3. Recommended Reset Sequence to Avoid Link Training Issues 9.4. SDC Timing Constraints
10. Throughput Optimization x
10.1. Throughput of Posted Writes 10.2. Throughput of Non-Posted Reads
11. Additional Features x
11.1. Configuration over Protocol (CvP) 11.2. Autonomous Mode 11.3. ECRC
11.2. Autonomous Mode x
11.2.1. Enabling Autonomous Mode 11.2.2. Enabling CvP Initialization
11.3. ECRC x
11.3.1. ECRC on the RX Path 11.3.2. ECRC on the TX Path
12. Debugging x
12.1. Hardware Bring-Up Issues 12.2. Link Training 12.3. Use Third-Party PCIe Analyzer 12.4. BIOS Enumeration Issues
12.2. Link Training x
12.2.1. Debugging Link that Fails To Reach L0
C. Document Revision History x
C.1. Cyclone® V Avalon® Memory Mapped (Avalon-MM) Interface for PCIe* Solutions User Guide Revision History
1. Datasheet
2. Getting Started with the Avalon-MM Design Example
3. Parameter Settings
4. 64- or 128-Bit Avalon-MM Interface to the Endpoint Application Layer
5. Registers
6. Interrupts for Endpoints
7. Error Handling
A. PCI Express Protocol Stack
8. Transceiver PHY IP Reconfiguration
9. Design Implementation
10. Throughput Optimization
11. Additional Features
12. Debugging
B. Lane Initialization and Reversal
C. Document Revision History

3.5. Avalon Memory‑Mapped System Settings

Table 18.  Avalon Memory-Mapped System Settings
Parameter Value Description
Avalon-MM data width

64-bit

128-bit

Specifies the data width for the Application Layer to Transaction Layer interface. Refer to Application Layer Clock Frequencies for All Combinations of Link Width, Data Rate and Application Layer Interface Widths for all legal combinations of data width, number of lanes, Application Layer clock frequency, and data rate.
Avalon-MM address width

32-bit

64-bit

Specifies the address width for Avalon-MM RX master ports that access Avalon-MM slaves in the Avalon address domain. When you select 32-bit addresses, the PCI Express Avalon-MM Bridge performs address translation. When you specify 64-bits addresses, no address translation is performed in either direction. The destination address specified is forwarded to the Avalon-MM interface without any changes.

For the Avalon-MM interface with DMA, this value must be set to 64.

Peripheral mode

Requester/Completer

Completer-Only

Specifies whether the Avalon‑MM Arria® V GZ Hard IP for PCI Express is capable of sending requests to the upstream PCI Express devices, and whether the incoming requests are pipelined.

Requester/Completer—In this mode, the Hard IP can send request packets on the PCI Express TX link and receive request packets on the PCI Express RX link.

Completer-Only—In this mode, the Hard IP can receive requests, but cannot initiate upstream requests. However, it can transmit completion packets on the PCI Express TX link. This mode removes the Avalon-MM TX slave port and thereby reduces logic utilization.

Single DW Completer On/Off

This is a non‑pipelined version of Completer Only mode. At any time, only a single request can be outstanding. Single DWORD completer uses fewer resources than Completer Only. This variant is targeted for systems that require simple read and write register accesses from a host CPU. If you select this option, the width of the data for RXM BAR masters is always 32 bits, regardless of the Avalon-MM width.

For the Avalon-MM interface with DMA, this value must be Off .

Control register access (CRA) Avalon-MM slave port On/Off

Allows read and write access to bridge registers from the interconnect fabric using a specialized slave port. This option is required for Requester/Completer variants and optional for Completer Only variants. Enabling this option allows read and write access to bridge registers, except in the Completer‑Only single DWORD variations.

Enable multiple MSI/MSI-X support On/Off

When you turn this option On, the core exports top‑level MSI and MSI‑X interfaces that you can use to implement a Customer Interrupt Handler for MSI and MSI‑X interrupts. For more information about the Custom Interrupt Handler, refer to Interrupts for End Points Using the Avalon-MM Interface with Multiple MSI/MSI‑X Support. If you turn this option Off, the core handles interrupts internally.

Auto enabled PCIe interrupt (enabled at power-on) On/Off

Turning on this option enables the Avalon‑MM Arria® V GZ Hard IP for PCI Express interrupt register at power‑up. Turning off this option disables the interrupt register at power‑up. The setting does not affect run‑time configuration of the interrupt enable register.

For the Avalon-MM interface with DMA, this value must be Off.

Enable hard IP status bus On/Off When you turn this option on, your top-level variant includes the signals necessary to connect to the Transceiver Reconfiguration Controller IP Core, your variant, including:
  • Link status signals
  • ECC error signals
  • TX and RX parity error signals
  • Completion header and data signals, indicating the total number of Completion TLPs currently stored in the RX buffer
Intel recommends that you include the Transceiver Reconfiguration Controller IP Core in your design to improve signal quality.
Enable hard IP status extension bus On/Off When you turn this option on, your top-level variant includes signals that are useful for debugging, including link training and status, error, and the Transaction Layer Configuration Space signals. The top-level variant also includes signals showing the start and end of packets, error, ready, and BAR signals for the native Avalon-ST interface that connects to the Transaction Layer. The following signals are included in the top-level variant:
  • Link status signals
  • ECC error signals
  • Transaction Layer Configuration Space signals
  • Avalon-ST packet, error, ready, and BAR signals
Avalon to PCIe Address Translation Settings
Number of address pages 1, 2, 4, 8, 16, 32,

64, 128, 256, 512

Specifies the number of pages required to translate Avalon-MM addresses to PCI Express addresses before a request packet is sent to the Transaction Layer. Each of the 512 possible entries corresponds to a base address of the PCI Express memory segment of a specific size. This parameter is only necessary when you select 32-bit addressing.

Size of address pages 4 KBytes–4 GBytes

Specifies the size of each memory segment. Each memory segment must be the same size. Refer to Avalon-MM-to-PCI Express Address Translation Algorithm for 32-Bit Bridge for more information about address translation. This parameter is only necessary when you select 32-bit addressing.

Level Two Title