AN 955: Programmer’s Configuration Debugger Tool

Download PDF
ID 691274
Date 4/01/2024
Public
Document Table of Contents
Document Table of Contents x
1. Programmer’s Configuration Debugger Tool 2. Debugging Tool Components 3. Document Revision History for AN 955: Programmer’s Configuration Debugger Tool
1. Programmer’s Configuration Debugger Tool x
1.1. Launching Debugger Tool
2. Debugging Tool Components x
2.1. Parsing Programming Files 2.2. Getting Device Information 2.3. Debugging QSPI Flash 2.4. QSPI Controller Settings and SFDP Values 2.5. Debugging Remote System Update 2.6. Voltage Sensor Monitoring 2.7. Temperature Sensor Monitoring 2.8. Hard Processor System (HPS) Cold Reset 2.9. Debug Log 2.10. SDM Mailbox Command
2.1. Parsing Programming Files x
2.1.1. Reading Programming File Information 2.1.2. Parsing Program Files Command Option 2.1.3. Programming File Formats
2.1.3. Programming File Formats x
2.1.3.1. SOF File Information 2.1.3.2. RBF File Information 2.1.3.3. PMSF File Information 2.1.3.4. JIC File Information 2.1.3.5. RPD File Information 2.1.3.6. POF File Information
2.2. Getting Device Information x
2.2.1. Reading Device Information from SDM-Based Devices 2.2.2. Reading Device Information from Legacy Devices
2.3. Debugging QSPI Flash x
2.3.1. Performing QSPI Flash Debugging
2.4. QSPI Controller Settings and SFDP Values x
2.4.1. Reading the QSPI Controller Settings and SFDP Values
2.4.1. Reading the QSPI Controller Settings and SFDP Values x
2.4.1.1. QSPI Flash Debugging Use Cases
2.5. Debugging Remote System Update x
2.5.1. Performing Remote System Update Debugging
2.6. Voltage Sensor Monitoring x
2.6.1. Reading Voltage Measurement
2.7. Temperature Sensor Monitoring x
2.7.1. Reading Temperature Measurement
2.8. Hard Processor System (HPS) Cold Reset x
2.8.1. Performing Hard Processor System (HPS) Cold Reset
2.9. Debug Log x
2.9.1. Getting the Debug Log
2.10. SDM Mailbox Command x
2.10.1. Sending SDM Mailbox Command 2.10.2. Command Options for Sending SDM Mailbox Command
1. Programmer’s Configuration Debugger Tool
2. Debugging Tool Components
3. Document Revision History for AN 955: Programmer’s Configuration Debugger Tool

2.5.1. Performing Remote System Update Debugging

To perform remote system update debugging:
  1. Click Hardware Setup to select a hardware setup to use for debugging.
  2. Click Load Device and select a device from the drop-down list if more than one device exists in the hardware setup.
  3. Click Flash.
    Note: The Flash tab is disabled if the selected device is not SDM-based.
  4. Select the Chip Select pin that connects to the targeted QSPI flash memory.
    Note: Agilex™ 7 and Agilex™ 5 devices support CS0 to CS3 for targeted QSPI flash memory.
  5. Click Auto-detect to auto-detect the QSPI Flash that is attached to the device.
  6. Click Remote System Update.
  7. Click Reset when you wish to reset the page.
  8. Click Image Update to trigger reconfiguration of an image at the specified start address.
  9. Click Read Image Address (Configuration Pointer Block) to list all the application image addresses from the Configuration Pointer Block (CPB0 or CPB1).
  10. Click Read Image Address (Sub-partition Table) to list all the RSU partitions information from the Sub-partition Table (SPT0 or SPT1).
  11. Click Read RSU Status to read the current RSU status information that includes:
    • Current images address displays the current image address.
    • Failing image address displays the failing image address when an error occurs.
    • Error code and corresponding Error Type upon the RSU failure.
    • Version displays the current software version.
    • Error Source displays the source information of the error.
    • Error Location displays the error location of the failing image.
    • Error Details displays the error details of the failing image.
    • Error Message provides the corresponding error messages when an error occurs.
    • Debug Suggestion provides the corresponding actions that can be taken to resolve the error.
    • Current Image Retry displays the current image retry counter value.
  12. Click Clear (Current Image Retry Counter) to clear the Current Image Retry Counter value.
  13. Click Clear (Error Log) to remove the Error Log data.
Figure 9. Remote System Update
Level Two Title