================================
General
================================
Device name: AGFA012R24A2E2V
Software version: Quartus Prime Version 21.3.0 Internal Build 52 04/12/2021 SC Pro Edition
JTAG user code: 0xFFFFFFFF
Configuration clock source: Internal Oscillator
Run configuration CPU from internal oscillator: FALSE

==================================
Configuration
==================================
Configuration scheme: Active Serial x4
Active serial clock source: 100 MHz maximum using Internal Oscillator
Remote system update MAX_RETRY count: 1
HPS present: FALSE

================================
Configuration Pin Options
================================
SDM_IO0: PWRMGT_SCL
SDM_IO1: AS_DATA1
SDM_IO2: AS_CLK
SDM_IO3: AS_DATA2
SDM_IO4: AS_DATA0
SDM_IO5: AS_nCSO0
SDM_IO6: AS_DATA3
SDM_IO7: AS_nCSO2
SDM_IO8: AS_nCSO3
SDM_IO9: AS_nCSO1
SDM_IO10: NA
SDM_IO11: NA
SDM_IO12: PWRMGT_SDA
SDM_IO13: NA
SDM_IO14: NA
SDM_IO15: AS_RESET
SDM_IO16: NA

================================
Power Management & VID
================================
Version: 2
VID enable: TRUE 
VID mode of operation: PMBus_MASTER
Bus speed mode: 100 KHz
Slave device type: LTM4677
Device address in PMBus Slave mode:
PMBus device 0 slave address: 40
PMBus device 1 slave address: 41
PMBus device 2 slave address: 0
PMBus device 3 slave address: 0
PMBus device 4 slave address: 0
PMBus device 5 slave address: 0
PMBus device 6 slave address: 0
PMBus device 7 slave address: 0
Voltage output format: LINEAR
Direct format coefficient m: 0
Direct format coefficient b: 0
Direct format coefficient R: 0
Linear format N: -12
Translated voltage value unit: VOLTS
Enable PAGE command: TRUE
Page value: 0xFF

==============================
Error Detection CRC
================================
Enable error detection check: TRUE
Minimum SEU interval: 10000
Enable internal scrubbing: FALSE
Allow SEU fault injection: FALSE

================================
CvP Settings
================================
Configuration via Protocol: OFF

================================
Partial Reconfiguration
================================
POF0 region ID: 0x01000000
POF0 hash: 0xA87221CC718DBEB7ED25EA8A89FA23AA54F3B6506008435894CBE093221E09B5
POF1 region ID: 0x01100000
POF1 hash: 0x2D5571D3B99FA1CCFEC811CE78736A108F9721C87CC1EFD8EE194371AA931B2A
POF2 region ID: 0x01200000
POF2 hash: 0x2D5571D3B99FA1CCFEC811CE78736A108F9721C87CC1EFD8EE194371AA931B2A
POF3 region ID: 0x01300000
POF3 hash: 0x2D5571D3B99FA1CCFEC811CE78736A108F9721C87CC1EFD8EE194371AA931B2A

================================
Security
================================
Enable configuration bitstream authentication: TRUE
Owner root key hash: 573FC8BA D4B4E1A5 DE78D7A5 8DE8E656 6A48CA63 2C6A64BC 7E5E31A8 7AA2DD4A AD9CB81C 4D0147C2 90ABE7D4 3A6B313F
Enable multi-authority: FALSE
Enable configuration bitstream encryption: TRUE
Encryption key storage location: BBRAM
Encryption update ratio: DISABLED
Enable scrambling: FALSE

================================
Anti-Tamper
================================
Anti-tamper response: DISABLE

================================
Security Options
================================
Disable JTAG: OFF
Force SDM clock to internal oscillator: OFF
Force encryption key update: OFF
Disable virtual eFuses: OFF
Lock security eFuses: OFF
Disable HPS debug: OFF
Disable encryption key in eFuses: OFF
Disable encryption key in BBRAM: OFF
Disable Intrinsic ID PUF-wrapped encryption key in Quad SPI: OFF

================================
Tiles
================================
H-tile state: UNPOWERED
H-tile state: UNPOWERED