Low Latency 40-Gbps Ethernet IP Core User Guide

Download PDF
ID 683745
Date 3/08/2021
Public
Document Table of Contents
Document Table of Contents x
1. About the LL 40GbE IP Core 2. Getting Started 3. Functional Description 4. Debugging the Link A. Arria 10 10GBASE-KR Registers B. Additional Information
1. About the LL 40GbE IP Core x
1.1. LL 40GbE IP Core Supported Features 1.2. IP Core Device Family and Speed Grade Support 1.3. IP Core Verification 1.4. Performance and Resource Utilization 1.5. Release Information
1.2. IP Core Device Family and Speed Grade Support x
1.2.1. LL 40GbE IP Core Device Family Support 1.2.2. LL 40GbE IP Core Device Speed Grade Support
1.3. IP Core Verification x
1.3.1. Simulation Environment 1.3.2. Compilation Checking 1.3.3. Hardware Testing
1.4. Performance and Resource Utilization x
1.4.1. Arria 10 Resource Utilization 1.4.2. Stratix V Resource Utilization
2. Getting Started x
2.1. Installation and Licensing for LL 40GbE IP Core for Stratix® V Devices 2.2. Installing and Licensing Intel® FPGA IP Cores 2.3. Specifying the IP Core Parameters and Options 2.4. IP Core Parameters 2.5. Files Generated for Stratix V Variations 2.6. Files Generated for Arria 10 Variations 2.7. Integrating Your IP Core in Your Design 2.8. IP Core Testbenches 2.9. Compiling the Full Design and Programming the FPGA 2.10. Initializing the IP Core
2.2. Installing and Licensing Intel® FPGA IP Cores x
2.2.1. Intel® FPGA IP Evaluation Mode
2.7. Integrating Your IP Core in Your Design x
2.7.1. Pin Assignments 2.7.2. External Transceiver Reconfiguration Controller Required in Stratix V Designs 2.7.3. Transceiver PLL Required in Arria 10 Designs 2.7.4. Handling Potential Jitter in Intel® Arria® 10 Devices 2.7.5. External Time-of-Day Module for Variations with 1588 PTP Feature 2.7.6. Clock Requirements for 40GBASE-KR4 Variations 2.7.7. External TX MAC PLL 2.7.8. Placement Settings for the LL 40GbE Core
2.8. IP Core Testbenches x
2.8.1. Testbench Behavior 2.8.2. Simulating the LL 40GbE IP Core With the Testbenches
2.8.2. Simulating the LL 40GbE IP Core With the Testbenches x
2.8.2.1. Generating the LL 40GbE Testbench 2.8.2.2. Optimizing the IP Core Simulation With the Testbenches 2.8.2.3. Optimization in the 40GBASE-KR4 Testbench 2.8.2.4. Simulating with the Modelsim Simulator 2.8.2.5. Simulating with the NCSim Simulator 2.8.2.6. Simulating with the VCS Simulator 2.8.2.7. Testbench Output Example
3. Functional Description x
3.1. High Level System Overview 3.2. LL 40GbE IP Core Functional Description 3.3. Signals 3.4. Software Interface: Registers 3.5. Ethernet Glossary
3.2. LL 40GbE IP Core Functional Description x
3.2.1. LL 40GbE IP Core TX Datapath 3.2.2. LL 40GbE IP Core TX Data Bus Interfaces 3.2.3. LL 40GbE IP Core RX Datapath 3.2.4. LL 40GbE IP Core RX Data Bus Interfaces 3.2.5. External Reconfiguration Controller 3.2.6. External Transceiver PLL 3.2.7. External TX MAC PLL 3.2.8. Congestion and Flow Control Using Pause Frames 3.2.9. Pause Control and Generation Interface 3.2.10. Pause Control Frame Filtering 3.2.11. Link Fault Signaling Interface 3.2.12. Statistics Counters Interface 3.2.13. 1588 Precision Time Protocol Interfaces 3.2.14. PHY Status Interface 3.2.15. Transceiver PHY Serial Data Interface 3.2.16. Low Latency 40GBASE-KR4 IP Core Variations 3.2.17. Control and Status Interface 3.2.18. Arria 10 Transceiver Reconfiguration Interface 3.2.19. Clocks 3.2.20. Resets
3.2.1. LL 40GbE IP Core TX Datapath x
3.2.1.1. Preamble, Start, and SFD Insertion 3.2.1.2. Address Insertion 3.2.1.3. Length/Type Field Processing 3.2.1.4. Frame Padding 3.2.1.5. Frame Check Sequence (CRC-32) Insertion 3.2.1.6. Inter-Packet Gap Generation and Insertion 3.2.1.7. Error Insertion Test and Debug Feature
3.2.2. LL 40GbE IP Core TX Data Bus Interfaces x
3.2.2.1. LL 40GbE IP Core User Interface Data Bus 3.2.2.2. LL 40GbE IP Core TX Data Bus with Adapters (Avalon-ST Interface) 3.2.2.3. LL 40GbE IP Core TX Data Bus Without Adapters (Custom Streaming Interface) 3.2.2.4. Bus Quantization Effects With Adapters 3.2.2.5. User Interface to Ethernet Transmission
3.2.2.5. User Interface to Ethernet Transmission x
3.2.2.5.1. Order of Transmission
3.2.3. LL 40GbE IP Core RX Datapath x
3.2.3.1. LL 40GbE IP Core RX Filtering 3.2.3.2. LL 40GbE IP Core Preamble Processing 3.2.3.3. IP Core Strict SFD Checking 3.2.3.4. LL 40GbE IP Core FCS (CRC-32) Removal 3.2.3.5. LL 40GbE IP Core CRC Checking 3.2.3.6. LL 40GbE IP Core Malformed Packet Handling 3.2.3.7. RX CRC Forwarding 3.2.3.8. Inter-Packet Gap 3.2.3.9. Pause Ignore 3.2.3.10. Control Frame Identification
3.2.4. LL 40GbE IP Core RX Data Bus Interfaces x
3.2.4.1. LL 40GbE IP Core User Interface Data Bus 3.2.4.2. LL 40GbE IP Core RX Data Bus with Adapters (Avalon-ST Interface) 3.2.4.3. LL 40GbE IP Core RX Data Bus Without Adapters (Custom Streaming Interface)
3.2.8. Congestion and Flow Control Using Pause Frames x
3.2.8.1. Conditions Triggering XOFF Frame Transmission 3.2.8.2. Conditions Triggering XON Frame Transmission
3.2.12. Statistics Counters Interface x
3.2.12.1. OctetOK Count Interface
3.2.13. 1588 Precision Time Protocol Interfaces x
3.2.13.1. Implementing a 1588 System That Includes a LL 40GbE Core 3.2.13.2. PTP Receive Functionality 3.2.13.3. PTP Transmit Functionality 3.2.13.4. External Time-of-Day Module for 1588 PTP Variations 3.2.13.5. PTP Timestamp and TOD Formats 3.2.13.6. 1588 PTP Interface Signals
3.3. Signals x
3.3.1. LL 40GbE IP Core Signals
3.4. Software Interface: Registers x
3.4.1. LL 40GbE IP Core Registers 3.4.2. LL 40GbE Hardware Design Example Registers
3.4.1. LL 40GbE IP Core Registers x
3.4.1.1. PHY Registers 3.4.1.2. Link Fault Signaling Registers 3.4.1.3. LL 40GBASE-KR4 Registers 3.4.1.4. LL 40GbE IP Core MAC Configuration Registers 3.4.1.5. Pause Registers 3.4.1.6. TX Statistics Registers 3.4.1.7. RX Statistics Registers 3.4.1.8. 1588 PTP Registers
3.4.2. LL 40GbE Hardware Design Example Registers x
3.4.2.1. Packet Client Registers
4. Debugging the Link x
4.1. Creating a Signal Tap Debug File to Match Your Design Hierarchy
A. Arria 10 10GBASE-KR Registers x
A.1. 10GBASE-KR PHY Register Definitions
B. Additional Information x
B.1. LL 40GbE IP Core User Guide Archives B.2. LL 40GbE IP Core User Guide Revision History
1. About the LL 40GbE IP Core
2. Getting Started
3. Functional Description
4. Debugging the Link
A. Arria 10 10GBASE-KR Registers
B. Additional Information

3.2.2.3. LL 40GbE IP Core TX Data Bus Without Adapters (Custom Streaming Interface)

Figure 15. TX Client to MAC Interface Without Adapters
Table 18.  Signals of the Custom Streaming TX Client InterfaceAll interface signals are clocked by the clk_txmac clock.

Signal Name

Direction

Description

din[127:0]

Input

Data bytes to send in big-endian mode.

Most significant 64-bit word is in the higher-order bits: bits[127:64]

The LL 40GbE IP core does not process incoming frames of less than nine bytes correctly. You must ensure such frames do not reach the TX client interface.

din_sop[1:0]

Input

Start of packet (SOP) location in the TX data bus. Only the most significant byte of each 64‑bit word may be a start of packet. Bits 63 and 127 are the allowed locations.

Bit 0 of din_sop corresponds to the data word in din[63:0].

din_eop[1:0]

Input

End of packet location in the TX data bus. Indicates the 64-bit word that holds the end-of-packet byte. Any byte may be the last byte in a packet.

Bit 0 of din_eop corresponds to the data word in din[63:0].

din_eop_empty[5:0]

Input

Indicates the number of empty (invalid) bytes in the end-of-packet 8-byte word indicated by din_eop.

If din_eop[z] has the value of 0, then the value of din_eop_empty[(z+2):z] does not matter. However, if din_eop[z] has the value of 1, then you must set the value of din_eop_empty[(z+2):z] to the number of empty (invalid) bytes in the end-of-packet word z.

For example, if you have a LL 40GbE IP core and want to indicate that in the current clk_txmac clock cycle, byte 6 in word 1 of din is an end-of-packet byte, and no other words hold an end-of-packet byte in the current clock cycle, you must set the value of din_eop to 2'b10 and the value of din_eop_empty to 6'b110_000.

din_idle[1:0]

Input

Indicates the words in din that hold Idle bytes or control information rather than Ethernet data. One-hot encoded.

din_req

Output

Indicates that input data was accepted by the IP core.
tx_error[1:0] Input When asserted in an EOP cycle (while din_eop is non-zero), directs the IP core to insert an error in the corresponding packet before sending it on the Ethernet link.

This signal is a test and debug feature. In loopback mode, the IP core recognizes the packet upon return as a malformed packet.

clk_txmac

Output

TX MAC clock. The clock frequency should be 312.5 MHz . The clk_txmac clock and the clk_rxmac clock (which clocks the RX datapath) are assumed to have the same frequency.

The IP core reads the bytes in big endian order. A packet may start in the most significant byte of any word. A packet may end on any byte.

Level Two Title