Arria V Avalon-ST Interface for PCIe Solutions User Guide

Download PDF
ID 683733
Date 6/03/2020
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Datasheet 2. Getting Started with the Arria V Hard IP for PCI Express 3. Parameter Settings 4. Interfaces and Signal Descriptions 5. Registers 6. Interrupts 7. Error Handling 8. IP Core Architecture 9. Transaction Layer Protocol (TLP) Details 10. Throughput Optimization 11. Design Implementation 12. Additional Features 13. Hard IP Reconfiguration 14. Transceiver PHY IP Reconfiguration 15. Testbench and Design Example 16. Debugging A. Transaction Layer Packet (TLP) Header Formats B. Lane Initialization and Reversal C. Document Revision History
1. Datasheet x
1.1. Arria V Avalon-ST Interface for PCIe Datasheet 1.2. Features 1.3. Release Information 1.4. Device Family Support 1.5. Configurations 1.6. Example Designs 1.7. Debug Features 1.8. IP Core Verification 1.9. Performance and Resource Utilization 1.10. Recommended Speed Grades 1.11. Creating a Design for PCI Express
1.8. IP Core Verification x
1.8.1. Compatibility Testing Environment
2. Getting Started with the Arria V Hard IP for PCI Express x
2.1. Qsys Design Flow 2.2. Modifying the Example Design 2.3. Using the IP Catalog To Generate Your Arria V Hard IP for PCI Express as a Separate Component
2.1. Qsys Design Flow x
2.1.1. Generating the Testbench 2.1.2. Simulating the Example Design 2.1.3. Generating Synthesis Files 2.1.4. Understanding the Files Generated 2.1.5. Understanding Physical Placement of the PCIe IP Core 2.1.6. Compiling the Design in the Quartus® Prime Software
3. Parameter Settings x
3.1. Avalon-ST System Settings 3.2. Link Capabilities 3.3. Port Function Parameters Shared Across All Port Functions 3.4. Port Function Parameters Defined Separately for All Port Functions
3.3. Port Function Parameters Shared Across All Port Functions x
3.3.1. Device Capabilities 3.3.2. Error Reporting 3.3.3. Link Capabilities 3.3.4. Slot Capabilities 3.3.5. Power Management
3.4. Port Function Parameters Defined Separately for All Port Functions x
3.4.1. Base Address Register (BAR) and Expansion ROM Settings 3.4.2. Base and Limit Registers for Root Ports 3.4.3. Device Identification Registers for Function <n> 3.4.4. Func <n> Device 3.4.5. Func <n> Link 3.4.6. Func <n> MSI and MSI-X Capabilities 3.4.7. Func <n> Legacy Interrupt
4. Interfaces and Signal Descriptions x
4.1. Arria V Hard IP for PCI Express with Avalon-ST Interface to the Application Layer 4.2. Clock Signals 4.3. Reset Signals 4.4. Hard IP Status 4.5. Error Signals 4.6. ECRC Forwarding 4.7. Interrupts for Endpoints 4.8. Interrupts for Root Ports 4.9. Completion Side Band Signals 4.10. Transaction Layer Configuration Space Signals 4.11. LMI Signals 4.12. Power Management Signals 4.13. Physical Layer Interface Signals
4.1. Arria V Hard IP for PCI Express with Avalon-ST Interface to the Application Layer x
4.1.1. Avalon‑ST RX Interface 4.1.2. Avalon-ST TX Interface
4.1.1. Avalon‑ST RX Interface x
4.1.1.1. Avalon-ST RX Component Specific Signals 4.1.1.2. Data Alignment and Timing for the 64‑Bit Avalon® -ST RX Interface 4.1.1.3. Data Alignment and Timing for the 128‑Bit Avalon‑ST RX Interface
4.1.2. Avalon-ST TX Interface x
4.1.2.1. Avalon-ST Packets to PCI Express TLPs 4.1.2.2. Data Alignment and Timing for the 64‑Bit Avalon-ST TX Interface 4.1.2.3. Data Alignment and Timing for the 128‑Bit Avalon‑ST TX Interface 4.1.2.4. Root Port Mode Configuration Requests
4.10. Transaction Layer Configuration Space Signals x
4.10.1. Configuration Space Register Access Timing 4.10.2. Configuration Space Register Access
4.13. Physical Layer Interface Signals x
4.13.1. Transceiver Reconfiguration 4.13.2. Serial Interface Signals 4.13.3. Hard IP Reconfiguration Interface 4.13.4. PIPE Interface Signals 4.13.5. Test Signals
4.13.2. Serial Interface Signals x
4.13.2.1. Physical Layout of Hard IP in Arria V Devices 4.13.2.2. Channel Placement in Arria V Devices
5. Registers x
5.1. Correspondence between Configuration Space Registers and the PCIe Specification 5.2. Type 0 Configuration Space Registers 5.3. Type 1 Configuration Space Registers 5.4. PCI Express Capability Structures 5.5. Intel-Defined VSEC Registers 5.6. CvP Registers 5.7. Uncorrectable Internal Error Mask Register 5.8. Uncorrectable Internal Error Status Register 5.9. Correctable Internal Error Mask Register 5.10. Correctable Internal Error Status Register
6. Interrupts x
6.1. Interrupts for Endpoints 6.2. Interrupts for Root Ports
6.1. Interrupts for Endpoints x
6.1.1. MSI Interrupts 6.1.2. MSI-X 6.1.3. Implementing MSI-X Interrupts
6.1.3. Implementing MSI-X Interrupts x
6.1.3.1. Legacy Interrupts
6.1.3.1. Legacy Interrupts x
6.1.3.1.1. Enabling MSI or Legacy Interrupts
7. Error Handling x
7.1. Physical Layer Errors 7.2. Data Link Layer Errors 7.3. Transaction Layer Errors 7.4. Error Reporting and Data Poisoning 7.5. Uncorrectable and Correctable Error Status Bits
8. IP Core Architecture x
8.1. Top-Level Interfaces 8.2. Transaction Layer 8.3. Data Link Layer 8.4. Physical Layer 8.5. Multi-Function Support
8.1. Top-Level Interfaces x
8.1.1. Avalon-ST Interface 8.1.2. Clocks and Reset 8.1.3. Local Management Interface (LMI Interface) 8.1.4. Hard IP Reconfiguration 8.1.5. Transceiver Reconfiguration 8.1.6. Interrupts 8.1.7. PIPE
8.2. Transaction Layer x
8.2.1. Configuration Space
9. Transaction Layer Protocol (TLP) Details x
9.1. Supported Message Types 9.2. Transaction Layer Routing Rules 9.3. Receive Buffer Reordering
9.1. Supported Message Types x
9.1.1. INTX Messages 9.1.2. Power Management Messages 9.1.3. Error Signaling Messages 9.1.4. Locked Transaction Message 9.1.5. Slot Power Limit Message 9.1.6. Vendor-Defined Messages 9.1.7. Hot Plug Messages
9.3. Receive Buffer Reordering x
9.3.1. Using Relaxed Ordering
10. Throughput Optimization x
10.1. Throughput of Posted Writes 10.2. Throughput of Non-Posted Reads
11. Design Implementation x
11.1. Making Analog QSF Assignments Using the Assignment Editor 11.2. Making Pin Assignments 11.3. Recommended Reset Sequence to Avoid Link Training Issues
12. Additional Features x
12.1. Configuration over Protocol (CvP) 12.2. Autonomous Mode 12.3. ECRC
12.2. Autonomous Mode x
12.2.1. Enabling Autonomous Mode 12.2.2. Enabling CvP Initialization
12.3. ECRC x
12.3.1. ECRC on the RX Path 12.3.2. ECRC on the TX Path
14. Transceiver PHY IP Reconfiguration x
14.1. Connecting the Transceiver Reconfiguration Controller IP Core 14.2. Transceiver Reconfiguration Controller Connectivity for Designs Using CvP
15. Testbench and Design Example x
15.1. Endpoint Testbench 15.2. Root Port Testbench 15.3. Test Driver Module 15.4. Root Port Design Example 15.5. Root Port BFM Overview 15.6. BFM Procedures and Functions 15.7. Setting Up Simulation
15.1. Endpoint Testbench x
15.1.1. Endpoint Testbench for SR-IOV
15.5. Root Port BFM Overview x
15.5.1. BFM Memory Map 15.5.2. Configuration Space Bus and Device Numbering 15.5.3. Configuration of Root Port and Endpoint 15.5.4. Issuing Read and Write Transactions to the Application Layer
15.6. BFM Procedures and Functions x
15.6.1. ebfm_barwr Procedure 15.6.2. ebfm_barwr_imm Procedure 15.6.3. ebfm_barrd_wait Procedure 15.6.4. ebfm_barrd_nowt Procedure 15.6.5. ebfm_cfgwr_imm_wait Procedure 15.6.6. ebfm_cfgwr_imm_nowt Procedure 15.6.7. ebfm_cfgrd_wait Procedure 15.6.8. ebfm_cfgrd_nowt Procedure 15.6.9. BFM Configuration Procedures 15.6.10. BFM Shared Memory Access Procedures 15.6.11. BFM Log and Message Procedures 15.6.12. Verilog HDL Formatting Functions
15.6.9. BFM Configuration Procedures x
15.6.9.1. ebfm_cfg_rp_ep Procedure 15.6.9.2. ebfm_cfg_decode_bar Procedure
15.6.10. BFM Shared Memory Access Procedures x
15.6.10.1. Shared Memory Constants 15.6.10.2. shmem_write Task 15.6.10.3. shmem_read Function 15.6.10.4. shmem_display Verilog HDL Function 15.6.10.5. shmem_fill Procedure 15.6.10.6. shmem_chk_ok Function
15.6.11. BFM Log and Message Procedures x
15.6.11.1. ebfm_display Verilog HDL Function 15.6.11.2. ebfm_log_stop_sim Verilog HDL Function 15.6.11.3. ebfm_log_set_suppressed_msg_mask Task 15.6.11.4. ebfm_log_set_stop_on_msg_mask Verilog HDL Task 15.6.11.5. ebfm_log_open Verilog HDL Function 15.6.11.6. ebfm_log_close Verilog HDL Function
15.6.12. Verilog HDL Formatting Functions x
15.6.12.1. himage1 15.6.12.2. himage2 15.6.12.3. himage4 15.6.12.4. himage8 15.6.12.5. himage16 15.6.12.6. dimage1 15.6.12.7. dimage2 15.6.12.8. dimage3 15.6.12.9. dimage4 15.6.12.10. dimage5 15.6.12.11. dimage6 15.6.12.12. dimage7
15.7. Setting Up Simulation x
15.7.1. Changing Between Serial and PIPE Simulation 15.7.2. Using the PIPE Interface for Gen1 and Gen2 Variants 15.7.3. Viewing the Important PIPE Interface Signals 15.7.4. Disabling the Scrambler for Gen1 and Gen2 Simulations 15.7.5. Disabling 8B/10B Encoding and Decoding for Gen1 and Gen2 Simulations 15.7.6. Changing between the Hard and Soft Reset Controller
16. Debugging x
16.1. Hardware Bring-Up Issues 16.2. Link Training 16.3. Use Third-Party PCIe Analyzer 16.4. BIOS Enumeration Issues
16.2. Link Training x
16.2.1. Link Hangs in L0 State
A. Transaction Layer Packet (TLP) Header Formats x
A.1. TLP Packet Formats without Data Payload A.2. TLP Packet Formats with Data Payload
C. Document Revision History x
C.1. Document Revision History of the Arria V Avalon® Streaming (Avalon-ST) Interface for PCIe* Solutions User Guide
1. Datasheet
2. Getting Started with the Arria V Hard IP for PCI Express
3. Parameter Settings
4. Interfaces and Signal Descriptions
5. Registers
6. Interrupts
7. Error Handling
8. IP Core Architecture
9. Transaction Layer Protocol (TLP) Details
10. Throughput Optimization
11. Design Implementation
12. Additional Features
13. Hard IP Reconfiguration
14. Transceiver PHY IP Reconfiguration
15. Testbench and Design Example
16. Debugging
A. Transaction Layer Packet (TLP) Header Formats
B. Lane Initialization and Reversal
C. Document Revision History

7.3. Transaction Layer Errors

Table 66.  Errors Detected by the Transaction Layer

Error

Type

Description

Poisoned TLP received

Uncorrectable (non-fatal)

This error occurs if a received Transaction Layer Packet has the EP poison bit set.

The received TLP is passed to the Application Layer and the Application Layer logic must take appropriate action in response to the poisoned TLP. Refer to “2.7.2.2 Rules for Use of Data Poisoning” in the PCI Express Base Specification for more information about poisoned TLPs.

ECRC check failed  (1)

Uncorrectable (non-fatal)

This error is caused by an ECRC check failing despite the fact that the TLP is not malformed and the LCRC check is valid.

The Hard IP block handles this TLP automatically. If the TLP is a non‑posted request, the Hard IP block generates a completion with completer abort status. In all cases the TLP is deleted in the Hard IP block and not presented to the Application Layer.

Unsupported Request for Endpoints

Uncorrectable (non-fatal)

This error occurs whenever a component receives any of the following Unsupported Requests:

  • Type 0 Configuration Requests for a non-existing function.
  • Completion transaction for which the Requester ID does not match the bus, device and function number.
  • Unsupported message.
  • A Type 1 Configuration Request TLP for the TLP from the PCIe link.
  • A locked memory read (MEMRDLK) on native Endpoint.
  • A locked completion transaction.
  • A 64-bit memory transaction in which the 32 MSBs of an address are set to 0.
  • A memory or I/O transaction for which there is no BAR match.
  • A memory transaction when the Memory Space Enable bit (bit [1] of the PCI Command register at Configuration Space offset 0x4) is set to 0.
  • A poisoned configuration write request (CfgWr0)

In all cases the TLP is deleted in the Hard IP block and not presented to the Application Layer. If the TLP is a non-posted request, the Hard IP block generates a completion with Unsupported Request status.

Unsupported Requests for Root Port

Uncorrectable (fatal)

This error occurs whenever a component receives an Unsupported Request including:

  • Unsupported message
  • A Type 0 Configuration Request TLP
  • A 64-bit memory transaction which the 32 MSBs of an address are set to 0.
  • A memory transaction that does not match the address range defined by the Base and Limit Address registers

Completion timeout

Uncorrectable (non-fatal)

This error occurs when a request originating from the Application Layer does not generate a corresponding completion TLP within the established time. It is the responsibility of the Application Layer logic to provide the completion timeout mechanism. The completion timeout should be reported from the Transaction Layer using the cpl_err[0] signal.

Completer abort  (1)

Uncorrectable (non-fatal)

The Application Layer reports this error using the cpl_err[2]signal when it aborts receipt of a TLP.

Unexpected completion

Uncorrectable (non-fatal)

This error is caused by an unexpected completion transaction. The Hard IP block handles the following conditions:

  • The Requester ID in the completion packet does not match the Configured ID of the Endpoint.
  • The completion packet has an invalid tag number. (Typically, the tag used in the completion packet exceeds the number of tags specified.)
  • The completion packet has a tag that does not match an outstanding request.
  • The completion packet for a request that was to I/O or Configuration Space has a length greater than 1 dword.
  • The completion status is Configuration Retry Status (CRS) in response to a request that was not to Configuration Space.

In all of the above cases, the TLP is not presented to the Application Layer; the Hard IP block deletes it.

The Application Layer can detect and report other unexpected completion conditions using the cpl_err[2] signal. For example, the Application Layer can report cases where the total length of the received successful completions do not match the original read request length.

Receiver overflow   (1)

Uncorrectable (fatal)

This error occurs when a component receives a TLP that violates the FC credits allocated for this type of TLP. In all cases the hard IP block deletes the TLP and it is not presented to the Application Layer.

Flow control protocol error (FCPE)  (1)

Uncorrectable (fatal)

This error occurs when a component does not receive update flow control credits with the 200 µs limit.

Malformed TLP

Uncorrectable (fatal)

This error is caused by any of the following conditions:

  • The data payload of a received TLP exceeds the maximum payload size.
  • The TD field is asserted but no TLP digest exists, or a TLP digest exists but the TD bit of the PCI Express request header packet is not asserted.
  • A TLP violates a byte enable rule. The Hard IP block checks for this violation, which is considered optional by the PCI Express specifications.
  • A TLP in which the type and length fields do not correspond with the total length of the TLP.
  • A TLP in which the combination of format and type is not specified by the PCI Express specification.
  • A request specifies an address/length combination that causes a memory space access to exceed a 4  KB boundary. The Hard IP block checks for this violation, which is considered optional by the PCI Express specification.
  • Messages, such as Assert_INTX, Power Management, Error Signaling, Unlock, and Set Power Slot Limit, must be transmitted across the default traffic class.

The Hard IP block deletes the malformed TLP; it is not presented to the Application Layer.

Note:

  1. Considered optional by the PCI Express Base Specification Revision.
Level Two Title