Parallel Flash Loader Intel® FPGA IP User Guide

Download PDF
ID 683698
Date 4/03/2023
Public
Document Table of Contents
Document Table of Contents x
1. Parallel Flash Loader Intel® FPGA IP User Guide
1. Parallel Flash Loader Intel® FPGA IP User Guide x
1.1. Features 1.2. Device Support 1.3. Functional Description 1.4. Using the PFL IP Core 1.5. PFL IP Core In Embedded Systems 1.6. Third-party Programmer Support 1.7. Parameters 1.8. Signals 1.9. Specifications 1.10. Parallel Flash Loader Intel® FPGA IP User Guide Archives 1.11. Document Revision History for the Parallel Flash Loader Intel® FPGA IP User Guide
1.2. Device Support x
1.2.1. Supported Flash Memory Devices 1.2.2. Supported Schemes and Features
1.3. Functional Description x
1.3.1. Programming Flash Memory 1.3.2. Controlling Intel® FPGA Configuration from Flash Memory 1.3.3. Mapping PFL and Flash Address 1.3.4. Implementing Page in the Flash .pof 1.3.5. Using Enhanced Bitstream Compression and Decompression 1.3.6. Using Remote System Upgrade
1.3.1. Programming Flash Memory x
1.3.1.1. Programming CFI Flash 1.3.1.2. Programming Quad SPI Flash 1.3.1.3. Programming NAND Flash
1.3.4. Implementing Page in the Flash .pof x
1.3.4.1. Storing Option Bits
1.3.6. Using Remote System Upgrade x
1.3.6.1. Remote System Upgrade State Machine in the PFL IP Core 1.3.6.2. Implementing Remote System Upgrade with the PFL IP Core 1.3.6.3. User Watchdog Timer
1.4. Using the PFL IP Core x
1.4.1. Converting .sof Files to a .pof 1.4.2. Constraining PFL Timing 1.4.3. Simulating PFL Design 1.4.4. Programming Intel® CPLDs and Flash Memory Devices 1.4.5. Defining New CFI Flash Device 1.4.6. Programming Multiple Flash Memory Devices 1.4.7. Creating Jam Files for Intel® CPLDs and Flash Memory Device Programming
1.4.2. Constraining PFL Timing x
1.4.2.1. Constraining Clock Signal 1.4.2.2. Constraining Synchronous Input and Output Ports 1.4.2.3. Constraining Asynchronous Input and Output Ports, and Bidirectional Synchronous Ports 1.4.2.4. Summary of PFL Timing Constraints
1.4.3. Simulating PFL Design x
1.4.3.1. Creating a Test Bench File for PFL Simulation 1.4.3.2. Performing PFL Simulation in the ModelSim- Intel® FPGA Software 1.4.3.3. Performing PFL Simulation for FPGA Configuration
1.4.4. Programming Intel® CPLDs and Flash Memory Devices x
1.4.4.1. Programming Intel® CPLDs and Flash Memory Devices Separately
1.9. Specifications x
1.9.1. Configuration Time Calculation Examples
1. Parallel Flash Loader Intel® FPGA IP User Guide

1.3.6.2. Implementing Remote System Upgrade with the PFL IP Core

You can achieve the remote system upgrade capabilities with the PFL IP core by controlling the fpga_pgm[2..0] and the pfl_nreconfigure ports.

To control the fpga_pgm[2..0] and the pfl_nreconfigure ports, user-defined logic must perform the following capabilities:

  • After FPGA power-up, user logic sets the fpga_pgm[2..0] ports to specify which page of configuration image is to be loaded from the flash.
  • After the remote host completes the new image update to the flash, user logic triggers a reconfiguration by pulling the pfl_nreconfigure pin low and setting the fpga_pgm[2..0] to the page in which the new image is located. The pfl_nreconfigure signal pulsed low for greater than one pfl_clk cycle.
  • If you have enabled the user watchdog timer, user logic can monitor the pfl_watchdog_error port to detect any occurrence of watchdog time-out error. If the pfl_watchdog_error pin is asserted high, this indicates watchdog time-out error. You can use the user logic to set the fpga_pgm[2..0] and pull the pfl_nreconfigure port low to initiate FPGA reconfiguration. The recovery page to be loaded from the flash memory device after watchdog timer error depends on the fpga_pgm[2..0] setting.
Figure 17. Implementation of Remote System Upgrade with the PFL IP Core
Level Two Title