Low Latency 50G Ethernet Intel® FPGA IP User Guide: Stratix® 10 Devices

Download PDF
ID 683675
Date 4/09/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the Low Latency 50G Ethernet IP Core 2. Getting Started 3. Low Latency 50G Ethernet Intel® FPGA IP Parameters 4. Functional Description 5. Interfaces and Signal Descriptions 6. IP Core Register Descriptions 7. Document Revision History for the Low Latency 50G Ethernet Intel® FPGA IP User Guide: Stratix® 10 Devices
1. About the Low Latency 50G Ethernet IP Core x
1.1. Release Information 1.2. Supported Features 1.3. Device Family Support 1.4. Device Speed Grade Support 1.5. IP Core Verification 1.6. Performance and Resource Utilization
1.5. IP Core Verification x
1.5.1. Simulation Environment 1.5.2. Compilation Checking 1.5.3. Hardware Testing
2. Getting Started x
2.1. Installing and Licensing Intel® FPGA IP Cores 2.2. Specifying the Low Latency 50G Ethernet IP Core Parameters and Options 2.3. Simulating the IP Core 2.4. Generated File Structure 2.5. Integrating Your IP Core in Your Design 2.6. Compiling the Full Design and Programming the FPGA
2.1. Installing and Licensing Intel® FPGA IP Cores x
2.1.1. Intel® FPGA IP Evaluation Mode
2.5. Integrating Your IP Core in Your Design x
2.5.1. Pin Assignments 2.5.2. Adding the Transceiver PLL 2.5.3. Placement Settings for the Low Latency 50G Ethernet IP Core
4. Functional Description x
4.1. TX MAC Datapath 4.2. TX PCS 4.3. RX MAC Datapath 4.4. RX PCS 4.5. Link Fault Signaling Interface 4.6. User Interface to Ethernet Transmission 4.7. Auto Negotiation and Link Training 4.8. Flow Control 4.9. Reset
4.1. TX MAC Datapath x
4.1.1. Frame Padding 4.1.2. Preamble Insertion 4.1.3. Inter-Packet Gap Generation and Insertion
4.3. RX MAC Datapath x
4.3.1. IP Core Preamble Processing 4.3.2. IP Core Strict SFD Checking 4.3.3. IP Core Malformed Packet Handling 4.3.4. Length/Type Field Processing 4.3.5. RX CRC Checking and Dynamic Forwarding
4.3.4. Length/Type Field Processing x
4.3.4.1. Length Checking
4.6. User Interface to Ethernet Transmission x
4.6.1. Order of Transmission 4.6.2. Bit Order For TX and RX Datapaths
4.8. Flow Control x
4.8.1. TX Pause/PFC Flow Control Transmission 4.8.2. XON/XOFF Pause Frames
5. Interfaces and Signal Descriptions x
5.1. TX MAC Interface to User Logic 5.2. RX MAC Interface to User Logic 5.3. Transceivers 5.4. Transceiver Reconfiguration Signals 5.5. Avalon® Memory-Mapped Management Interface 5.6. Miscellaneous Status and Debug Signals 5.7. Reset Signals 5.8. Flow Control Interface
5.4. Transceiver Reconfiguration Signals x
5.4.1. Disabling Background Calibration
6. IP Core Register Descriptions x
6.1. PHY Registers 6.2. TX MAC Registers 6.3. RX MAC Registers 6.4. Flow Control Registers 6.5. Statistics Registers 6.6. Auto-Negotiation and Link Training Registers
6.5. Statistics Registers x
6.5.1. TX Statistics Registers 6.5.2. RX Statistics Registers
6.6. Auto-Negotiation and Link Training Registers x
6.6.1. AN/LT Sequencer Config AN/LT Sequencer Config Fields 6.6.2. AN/LT Sequencer Status 6.6.3. Auto Negotiation Config Register 1 6.6.4. Auto Negotiation Config Register 2 6.6.5. Auto Negotiation Status Register 6.6.6. Auto Negotiation Config Register 3 6.6.7. Auto Negotiation Config Register 4 6.6.8. Auto Negotiation Config Register 5 6.6.9. Auto Negotiation Config Register 6 6.6.10. Auto Negotiation Status Register 1 6.6.11. Auto Negotiation Status Register 2 6.6.12. Auto Negotiation Status Register 3 6.6.13. Auto Negotiation Status Register 4 6.6.14. Auto Negotiation Status Register 5 6.6.15. Link Training Config Register 1 6.6.16. Link Training Config Register 2 6.6.17. Link Training Status Register 1 6.6.18. Link Training Config Register for Lane 0 6.6.19. Link Training Frame Contents for Lane 0 6.6.20. Local Transceiver TX EQ 1 Settings for Lane 0 6.6.21. Local Transceiver TX EQ 2 Settings for Lane 0 6.6.22. Local Link Training Parameters 6.6.23. Link Training Config Register for Lane 1 6.6.24. Link Training Frame Contents for Lane 1 6.6.25. Local Transceiver TX EQ 1 Settings for Lane 1 6.6.26. Local Transceiver TX EQ 2 Settings for Lane 1 6.6.27. Link Training Config Register for Lane 2 6.6.28. Link Training Frame Contents for Lane 2 6.6.29. Local Transceiver TX EQ 1 Settings for Lane 2 6.6.30. Local Transceiver TX EQ 2 Settings for Lane 2 6.6.31. Link Training Config Register for Lane 3 6.6.32. Link Training Frame Contents for Lane 3 6.6.33. Local Transceiver TX EQ 1 Settings for Lane 3 6.6.34. Local Transceiver TX EQ 2 Settings for Lane 3
1. About the Low Latency 50G Ethernet IP Core
2. Getting Started
3. Low Latency 50G Ethernet Intel® FPGA IP Parameters
4. Functional Description
5. Interfaces and Signal Descriptions
6. IP Core Register Descriptions
7. Document Revision History for the Low Latency 50G Ethernet Intel® FPGA IP User Guide: Stratix® 10 Devices

6.6.1. AN/LT Sequencer Config

Provides the following config bits:
  • Reset AN/LT Sequencer
  • Disable AN Timer
  • Disable Link Fail Timer
  • Force Sequencer Mode
  • Link Training failure response
  • Link Fail if HiBER on/off
  • Skip LT on AN timeout when HiBER not used on/off

Offset: 0xB0

Access: RW

AN/LT Sequencer Config Fields

Bit Name Description Access Reset
14 skip_lt_on_an_timeout Skip Link Training on Auto Negotiation Timeout

1: If AN times out skip LT before attempting data mode, and use the previous LT settings

0: Use the normal AN/LT sequence, even if link_fail_if_hiber=0

  • This option is provided to speed up re-lock times when the link is known not to be resetting due to problems with link integrity
RW 0x0
13 link_fail_if_hiber Link Fail if HiBER

1: Trigger a link failure if a HiBER condition is detected in the PCS during data mode (default)

0: Ignore HiBER

RW 0x1
12 lt_failure_response Link Training Failure Response

1: Upon LT failure, PHY will go to data mode

0: Upon LT failure, PHY will restart AN, or if AN is disabled, skip AN and restart LT

  • This CSR defaults to 0 in hardware (synthesis)
  • We recommend setting this to 1 for simulation to avoid the need to model line conditions
RW 0x0
7:4 seq_force_mode Force the sequencer into a specific protocol

4'b0000: No force

4'b0011: 50GBASE-R2

All other settings are reserved

  • Forces the AN/LT Sequencer into a specific protocol, ignoring the AN result
  • AN/LT will still be cycled if enabled; configure AN and LT using their respective CFG registers
RW 0x0
2 disable_lf_timer Disable Link Fail Inhibit Timer

1: Disable the link fail inhibit timer

0: If PCS link fails, then AN will restart

  • The most common reason to disable the link fail inhibit timer is to characterize the link's behavior with link training
  • Turning off the link fail inhibit timer prevents link training from cycling, allowing each failure to be examined individually
RW 0x0
1 disable_an_timer Disable Auto Negotiation Timer

1: AN will wait for valid partner without timing out (default)

0: If AN fails, the Sequencer will try a different protocol

RW 0x1
0 reset_seq Reset AN/LT Sequencer

1: Reset only the AN/LT Sequencer. May initiate a PCS reconfiguration and/or AN/LT reset

0: Normal operation

 RW 0x0
Level Two Title