Low Latency 50G Ethernet Intel® FPGA IP User Guide: Stratix® 10 Devices

Download PDF
ID 683675
Date 4/09/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the Low Latency 50G Ethernet IP Core 2. Getting Started 3. Low Latency 50G Ethernet Intel® FPGA IP Parameters 4. Functional Description 5. Interfaces and Signal Descriptions 6. IP Core Register Descriptions 7. Document Revision History for the Low Latency 50G Ethernet Intel® FPGA IP User Guide: Stratix® 10 Devices
1. About the Low Latency 50G Ethernet IP Core x
1.1. Release Information 1.2. Supported Features 1.3. Device Family Support 1.4. Device Speed Grade Support 1.5. IP Core Verification 1.6. Performance and Resource Utilization
1.5. IP Core Verification x
1.5.1. Simulation Environment 1.5.2. Compilation Checking 1.5.3. Hardware Testing
2. Getting Started x
2.1. Installing and Licensing Intel® FPGA IP Cores 2.2. Specifying the Low Latency 50G Ethernet IP Core Parameters and Options 2.3. Simulating the IP Core 2.4. Generated File Structure 2.5. Integrating Your IP Core in Your Design 2.6. Compiling the Full Design and Programming the FPGA
2.1. Installing and Licensing Intel® FPGA IP Cores x
2.1.1. Intel® FPGA IP Evaluation Mode
2.5. Integrating Your IP Core in Your Design x
2.5.1. Pin Assignments 2.5.2. Adding the Transceiver PLL 2.5.3. Placement Settings for the Low Latency 50G Ethernet IP Core
4. Functional Description x
4.1. TX MAC Datapath 4.2. TX PCS 4.3. RX MAC Datapath 4.4. RX PCS 4.5. Link Fault Signaling Interface 4.6. User Interface to Ethernet Transmission 4.7. Auto Negotiation and Link Training 4.8. Flow Control 4.9. Reset
4.1. TX MAC Datapath x
4.1.1. Frame Padding 4.1.2. Preamble Insertion 4.1.3. Inter-Packet Gap Generation and Insertion
4.3. RX MAC Datapath x
4.3.1. IP Core Preamble Processing 4.3.2. IP Core Strict SFD Checking 4.3.3. IP Core Malformed Packet Handling 4.3.4. Length/Type Field Processing 4.3.5. RX CRC Checking and Dynamic Forwarding
4.3.4. Length/Type Field Processing x
4.3.4.1. Length Checking
4.6. User Interface to Ethernet Transmission x
4.6.1. Order of Transmission 4.6.2. Bit Order For TX and RX Datapaths
4.8. Flow Control x
4.8.1. TX Pause/PFC Flow Control Transmission 4.8.2. XON/XOFF Pause Frames
5. Interfaces and Signal Descriptions x
5.1. TX MAC Interface to User Logic 5.2. RX MAC Interface to User Logic 5.3. Transceivers 5.4. Transceiver Reconfiguration Signals 5.5. Avalon® Memory-Mapped Management Interface 5.6. Miscellaneous Status and Debug Signals 5.7. Reset Signals 5.8. Flow Control Interface
5.4. Transceiver Reconfiguration Signals x
5.4.1. Disabling Background Calibration
6. IP Core Register Descriptions x
6.1. PHY Registers 6.2. TX MAC Registers 6.3. RX MAC Registers 6.4. Flow Control Registers 6.5. Statistics Registers 6.6. Auto-Negotiation and Link Training Registers
6.5. Statistics Registers x
6.5.1. TX Statistics Registers 6.5.2. RX Statistics Registers
6.6. Auto-Negotiation and Link Training Registers x
6.6.1. AN/LT Sequencer Config 6.6.2. AN/LT Sequencer Status 6.6.3. Auto Negotiation Config Register 1 6.6.4. Auto Negotiation Config Register 2 6.6.5. Auto Negotiation Status Register 6.6.6. Auto Negotiation Config Register 3 6.6.7. Auto Negotiation Config Register 4 6.6.8. Auto Negotiation Config Register 5 6.6.9. Auto Negotiation Config Register 6 6.6.10. Auto Negotiation Status Register 1 6.6.11. Auto Negotiation Status Register 2 6.6.12. Auto Negotiation Status Register 3 6.6.13. Auto Negotiation Status Register 4 6.6.14. Auto Negotiation Status Register 5 6.6.15. Link Training Config Register 1 6.6.16. Link Training Config Register 2 6.6.17. Link Training Status Register 1 6.6.18. Link Training Config Register for Lane 0 6.6.19. Link Training Frame Contents for Lane 0 6.6.20. Local Transceiver TX EQ 1 Settings for Lane 0 6.6.21. Local Transceiver TX EQ 2 Settings for Lane 0 6.6.22. Local Link Training Parameters 6.6.23. Link Training Config Register for Lane 1 6.6.24. Link Training Frame Contents for Lane 1 6.6.25. Local Transceiver TX EQ 1 Settings for Lane 1 6.6.26. Local Transceiver TX EQ 2 Settings for Lane 1 6.6.27. Link Training Config Register for Lane 2 6.6.28. Link Training Frame Contents for Lane 2 6.6.29. Local Transceiver TX EQ 1 Settings for Lane 2 6.6.30. Local Transceiver TX EQ 2 Settings for Lane 2 6.6.31. Link Training Config Register for Lane 3 6.6.32. Link Training Frame Contents for Lane 3 6.6.33. Local Transceiver TX EQ 1 Settings for Lane 3 6.6.34. Local Transceiver TX EQ 2 Settings for Lane 3
1. About the Low Latency 50G Ethernet IP Core
2. Getting Started
3. Low Latency 50G Ethernet Intel® FPGA IP Parameters
4. Functional Description
5. Interfaces and Signal Descriptions
6. IP Core Register Descriptions
7. Document Revision History for the Low Latency 50G Ethernet Intel® FPGA IP User Guide: Stratix® 10 Devices

2.5.2. Adding the Transceiver PLL

The Low Latency 50G Ethernet IP core requires one TX transceiver PLLs that are not part of the IP core, to compile and to function correctly in hardware. On Stratix® 10 devices, only the ATX PLL supports the required data rate.

The transceiver PLLs you configure are physically present on the device, but the Low Latency 50G Ethernet IP core does not configure and connect them.

Figure 5. PLL Configuration Example for Low Latency 50G Ethernet IP Core Variation
To configure ATX PLL:
  • Set VCCR_GXB and VCCT_GXB supply voltage for the Transceiver to 1_1V.
  • Set Primary PLL clock output buffer to GXT clock output buffer.
  • Turn on Enable GXT local clock output port (tx_serial_clk_gxt).
  • Set GXT output clock source to Local ATX PLL.
  • Set PLL output frequency to 12890.625 MHz. The transceiver performs dual edge clocking, using both the rising and falling edges of the input clock from the PLL. Therefore, this PLL output frequency setting supports a 25.78125 Gbps data rate through the transceiver.
  • Set PLL auto mode reference clock frequency to the value you specified for the PHY reference frequency parameter.

When you generate an Low Latency 50G Ethernet IP core, the software also generates the HDL code for an ATX PLL. However, the HDL code for the Low Latency 50G Ethernet IP core does not instantiate the ATX PLL. If you choose to use the ATX PLL provided with the Low Latency 50G Ethernet IP core, you must instantiate and connect the instances of the ATX PLL with the Low Latency 50G Ethernet IP core in user logic.

If you generate your own ATX PLL, you must ensure its file name differs from the PLL provided with the IP core.
Note: If your design includes multiple instances of the Low Latency 50G Ethernet IP core, do not use the ATX PLL HDL code provided with the IP core. Instead, generate new ATX PLL IP cores to connect in your design.
Level Two Title