Arria® 10 and Cyclone® 10 GX Avalon® Streaming Interface for PCI Express* User Guide

Download PDF
ID 683647
Date 9/11/2024
Public
Document Table of Contents
Document Table of Contents x
1. Datasheet 2. Quick Start Guide 3. Arria® 10 or Cyclone® 10 GX Parameter Settings 4. Physical Layout 5. Interfaces and Signal Descriptions 6. Registers 7. Reset and Clocks 8. Interrupts 9. Error Handling 10. PCI Express Protocol Stack 11. Transaction Layer Protocol (TLP) Details 12. Throughput Optimization 13. Design Implementation 14. Additional Features 15. Hard IP Reconfiguration 16. Testbench and Design Example 17. Debugging A. Transaction Layer Packet (TLP) Header Formats B. Lane Initialization and Reversal C. Arria® 10 or Cyclone® 10 GX Avalon-ST Interface for PCIe Solutions User Guide Archive D. Document Revision History
1. Datasheet x
1.1. Arria® 10 or Cyclone® 10 GX Avalon-ST Interface for PCI Express* Datasheet 1.2. Release Information 1.3. Device Family Support 1.4. Configurations 1.5. Debug Features 1.6. IP Core Verification 1.7. Resource Utilization 1.8. Recommended Speed Grades 1.9. Creating a Design for PCI Express
1.1. Arria® 10 or Cyclone® 10 GX Avalon-ST Interface for PCI Express* Datasheet x
1.1.1. Arria® 10 or Cyclone® 10 GX Features
1.6. IP Core Verification x
1.6.1. Compatibility Testing Environment
2. Quick Start Guide x
2.1. Directory Structure 2.2. Design Components 2.3. Generating the Design 2.4. Simulating the Design 2.5. Compiling and Testing the Design in Hardware
3. Arria® 10 or Cyclone® 10 GX Parameter Settings x
3.1. Parameters 3.2. Arria® 10 or Cyclone® 10 GX Avalon-ST Settings 3.3. Base Address Register (BAR) and Expansion ROM Settings 3.4. Base and Limit Registers for Root Ports 3.5. Device Identification Registers 3.6. PCI Express and PCI Capabilities Parameters 3.7. Vendor Specific Extended Capability (VSEC) 3.8. Configuration, Debug, and Extension Options 3.9. PHY Characteristics 3.10. Example Designs
3.6. PCI Express and PCI Capabilities Parameters x
3.6.1. PCI Express and PCI Capabilities 3.6.2. Error Reporting 3.6.3. Link Capabilities 3.6.4. MSI and MSI-X Capabilities 3.6.5. Slot Capabilities 3.6.6. Power Management
4. Physical Layout x
4.1. Hard IP Block Placement In Cyclone® 10 GX Devices 4.2. Hard IP Block Placement In Arria® 10 Devices 4.3. Channel and Pin Placement for the Gen1, Gen2, and Gen3 Data Rates 4.4. Channel Placement and fPLL and ATX PLL Usage for the Gen3 Data Rate 4.5. PCI Express Gen3 Bank Usage Restrictions
5. Interfaces and Signal Descriptions x
5.1. Clock Signals 5.2. Reset, Status, and Link Training Signals 5.3. ECRC Forwarding 5.4. Error Signals 5.5. Interrupts for Endpoints 5.6. Interrupts for Root Ports 5.7. Completion Side Band Signals 5.8. Parity Signals 5.9. LMI Signals 5.10. Transaction Layer Configuration Space Signals 5.11. Hard IP Reconfiguration Interface 5.12. Power Management Signals 5.13. Physical Layer Interface Signals
5.10. Transaction Layer Configuration Space Signals x
5.10.1. Configuration Space Register Access Timing 5.10.2. Configuration Space Register Access
5.13. Physical Layer Interface Signals x
5.13.1. Serial Data Signals 5.13.2. PIPE Interface Signals 5.13.3. Test Signals 5.13.4. Arria® 10 Development Kit Conduit Interface
6. Registers x
6.1. Correspondence between Configuration Space Registers and the PCIe Specification 6.2. Type 0 Configuration Space Registers 6.3. Type 1 Configuration Space Registers 6.4. PCI Express Capability Structures 6.5. Intel-Defined VSEC Registers 6.6. Advanced Error Reporting Capability
6.5. Intel-Defined VSEC Registers x
6.5.1. CvP Registers
6.6. Advanced Error Reporting Capability x
6.6.1. Uncorrectable Internal Error Mask Register 6.6.2. Uncorrectable Internal Error Status Register 6.6.3. Correctable Internal Error Mask Register 6.6.4. Correctable Internal Error Status Register
7. Reset and Clocks x
7.1. Reset Sequence for Hard IP for PCI Express IP Core and Application Layer 7.2. Clocks
7.2. Clocks x
7.2.1. Clock Domains 7.2.2. Clock Summary
7.2.1. Clock Domains x
7.2.1.1. coreclkout_hip 7.2.1.2. pld_clk
8. Interrupts x
8.1. Interrupts for Endpoints 8.2. Interrupts for Root Ports
8.1. Interrupts for Endpoints x
8.1.1. MSI and Legacy Interrupts 8.1.2. MSI-X 8.1.3. Implementing MSI-X Interrupts 8.1.4. Legacy Interrupts
9. Error Handling x
9.1. Physical Layer Errors 9.2. Data Link Layer Errors 9.3. Transaction Layer Errors 9.4. Error Reporting and Data Poisoning 9.5. Uncorrectable and Correctable Error Status Bits
10. PCI Express Protocol Stack x
10.1. Top-Level Interfaces 10.2. Transaction Layer 10.3. Data Link Layer 10.4. Physical Layer
10.1. Top-Level Interfaces x
10.1.1. Avalon-ST Interface 10.1.2. Clocks and Reset 10.1.3. Local Management Interface (LMI Interface) 10.1.4. Hard IP Reconfiguration 10.1.5. Interrupts 10.1.6. PIPE
10.2. Transaction Layer x
10.2.1. Configuration Space
11. Transaction Layer Protocol (TLP) Details x
11.1. Supported Message Types 11.2. Transaction Layer Routing Rules 11.3. Receive Buffer Reordering
11.1. Supported Message Types x
11.1.1. INTX Messages 11.1.2. Power Management Messages 11.1.3. Error Signaling Messages 11.1.4. Locked Transaction Message 11.1.5. Slot Power Limit Message 11.1.6. Vendor-Defined Messages 11.1.7. Hot Plug Messages
11.3. Receive Buffer Reordering x
11.3.1. Using Relaxed Ordering
12. Throughput Optimization x
12.1. Throughput of Posted Writes 12.2. Throughput of Non-Posted Reads
13. Design Implementation x
13.1. Making Pin Assignments to Assign I/O Standard to Serial Data Pins 13.2. Recommended Reset Sequence to Avoid Link Training Issues 13.3. SDC Timing Constraints
14. Additional Features x
14.1. Configuration over Protocol (CvP) 14.2. Autonomous Mode 14.3. ECRC
14.2. Autonomous Mode x
14.2.1. Enabling Autonomous Mode 14.2.2. Enabling CvP Initialization
14.3. ECRC x
14.3.1. ECRC on the RX Path 14.3.2. ECRC on the TX Path
16. Testbench and Design Example x
16.1. Endpoint Testbench 16.2. Test Driver Module 16.3. Root Port BFM Overview 16.4. BFM Procedures and Functions
16.1. Endpoint Testbench x
16.1.1. Endpoint Testbench for SR-IOV
16.3. Root Port BFM Overview x
16.3.1. BFM Memory Map 16.3.2. Configuration Space Bus and Device Numbering 16.3.3. Configuration of Root Port and Endpoint 16.3.4. Issuing Read and Write Transactions to the Application Layer
16.4. BFM Procedures and Functions x
16.4.1. ebfm_barwr Procedure 16.4.2. ebfm_barwr_imm Procedure 16.4.3. ebfm_barrd_wait Procedure 16.4.4. ebfm_barrd_nowt Procedure 16.4.5. ebfm_cfgwr_imm_wait Procedure 16.4.6. ebfm_cfgwr_imm_nowt Procedure 16.4.7. ebfm_cfgrd_wait Procedure 16.4.8. ebfm_cfgrd_nowt Procedure 16.4.9. BFM Configuration Procedures 16.4.10. BFM Shared Memory Access Procedures 16.4.11. BFM Log and Message Procedures 16.4.12. Verilog HDL Formatting Functions
16.4.9. BFM Configuration Procedures x
16.4.9.1. ebfm_cfg_rp_ep Procedure 16.4.9.2. ebfm_cfg_decode_bar Procedure
16.4.10. BFM Shared Memory Access Procedures x
16.4.10.1. Shared Memory Constants 16.4.10.2. shmem_write Task 16.4.10.3. shmem_read Function 16.4.10.4. shmem_display Verilog HDL Function 16.4.10.5. shmem_fill Procedure 16.4.10.6. shmem_chk_ok Function
16.4.11. BFM Log and Message Procedures x
16.4.11.1. ebfm_display Verilog HDL Function 16.4.11.2. ebfm_log_stop_sim Verilog HDL Function 16.4.11.3. ebfm_log_set_suppressed_msg_mask Task 16.4.11.4. ebfm_log_set_stop_on_msg_mask Verilog HDL Task 16.4.11.5. ebfm_log_open Verilog HDL Function 16.4.11.6. ebfm_log_close Verilog HDL Function
16.4.12. Verilog HDL Formatting Functions x
16.4.12.1. himage1 16.4.12.2. himage2 16.4.12.3. himage4 16.4.12.4. himage8 16.4.12.5. himage16 16.4.12.6. dimage1 16.4.12.7. dimage2 16.4.12.8. dimage3 16.4.12.9. dimage4 16.4.12.10. dimage5 16.4.12.11. dimage6 16.4.12.12. dimage7
17. Debugging x
17.1. Simulation Fails To Progress Beyond Polling.Active State 17.2. Hardware Bring-Up Issues 17.3. Link Training 17.4. Creating a Signal Tap Debug File to Match Your Design Hierarchy 17.5. Use Third-Party PCIe Analyzer 17.6. BIOS Enumeration Issues
17.3. Link Training x
17.3.1. Link Hangs in L0 State
A. Transaction Layer Packet (TLP) Header Formats x
A.1. TLP Packet Formats without Data Payload A.2. TLP Packet Formats with Data Payload
D. Document Revision History x
D.1. Document Revision History of the Arria® 10 or Cyclone® 10 GX Avalon® Streaming (Avalon-ST) Interface for PCIe* Solutions User Guide
1. Datasheet
2. Quick Start Guide
3. Arria® 10 or Cyclone® 10 GX Parameter Settings
4. Physical Layout
5. Interfaces and Signal Descriptions
6. Registers
7. Reset and Clocks
8. Interrupts
9. Error Handling
10. PCI Express Protocol Stack
11. Transaction Layer Protocol (TLP) Details
12. Throughput Optimization
13. Design Implementation
14. Additional Features
15. Hard IP Reconfiguration
16. Testbench and Design Example
17. Debugging
A. Transaction Layer Packet (TLP) Header Formats
B. Lane Initialization and Reversal
C. Arria® 10 or Cyclone® 10 GX Avalon-ST Interface for PCIe Solutions User Guide Archive
D. Document Revision History

16.3.3. Configuration of Root Port and Endpoint

Before you issue transactions to the Endpoint, you must configure the Root Port and Endpoint Configuration Space registers. Use ebfm_cfg_rp_ep in altpcietb_bfm_configure.v to configure these registers.

The ebfm_cfg_rp_ep procedure executes the following steps to initialize the Configuration Space:

  1. Sets the Root Port Configuration Space to enable the Root Port to send transactions on the PCI Express link.
  2. Sets the Root Port and Endpoint PCI Express Capability Device Control registers as follows:
    1. Disables Error Reporting in both the Root Port and Endpoint. The BFM does not have error handling capability.
    2. Enables Relaxed Ordering in both Root Port and Endpoint.
    3. Enables Extended Tags for the Endpoint if the Endpoint has that capability.
    4. Disables Phantom Functions, Aux Power PM, and No Snoop in both the Root Port and Endpoint.
    5. Sets the Max Payload Size to the value that the Endpoint supports because the Root Port supports the maximum payload size.
    6. Sets the Root Port Max Read Request Size to 4 KB because the example Endpoint design supports breaking the read into as many completions as necessary.
    7. Sets the Endpoint Max Read Request Size equal to the Max Payload Size because the Root Port does not support breaking the read request into multiple completions.
  3. Assigns values to all the Endpoint BAR registers. The BAR addresses are assigned by the algorithm outlined below.
    1. I/O BARs are assigned smallest to largest starting just above the ending address of BFM shared memory in I/O space and continuing as needed throughout a full 32-bit I/O space.
    2. The 32-bit non-prefetchable memory BARs are assigned smallest to largest, starting just above the ending address of BFM shared memory in memory space and continuing as needed throughout a full 32-bit memory space.
    3. The value of the addr_map_4GB_limit input to the ebfm_cfg_rp_ep procedure controls the assignment of the 32-bit prefetchable and 64-bit prefetchable memory BARS. The default value of the addr_map_4GB_limit is 0.

      If the addr_map_4GB_limit input to the ebfm_cfg_rp_ep procedure is set to 0, then the ebfm_cfg_rp_ep procedure assigns the 32‑bit prefetchable memory BARs largest to smallest, starting at the top of 32-bit memory space and continuing as needed down to the ending address of the last 32-bit non-prefetchable BAR.

      However, if the addr_map_4GB_limit input is set to 1, the address map is limited to 4 GB. The ebfm_cfg_rp_ep procedure assigns 32-bit and 64-bit prefetchable memory BARs largest to smallest, starting at the top of the 32-bit memory space and continuing as needed down to the ending address of the last 32-bit non-prefetchable BAR.

    4. If the addr_map_4GB_limit input to the ebfm_cfg_rp_ep procedure is set to 0, then the ebfm_cfg_rp_ep procedure assigns the 64-bit prefetchable memory BARs smallest to largest starting at the 4 GB address assigning memory ascending above the 4 GB limit throughout the full 64-bit memory space.

      If the addr_map_4 GB_limit input to the ebfm_cfg_rp_ep procedure is set to 1, the ebfm_cfg_rp_ep procedure assigns the 32-bit and the 64-bit prefetchable memory BARs largest to smallest starting at the 4 GB address and assigning memory by descending below the 4 GB address to memory addresses as needed down to the ending address of the last 32-bit non-prefetchable BAR.

      The above algorithm cannot always assign values to all BARs when there are a few very large (1 GB or greater) 32-bit BARs. Although assigning addresses to all BARs may be possible, a more complex algorithm would be required to effectively assign these addresses. However, such a configuration is unlikely to be useful in real systems. If the procedure is unable to assign the BARs, it displays an error message and stops the simulation.

  4. Based on the above BAR assignments, the ebfm_cfg_rp_ep procedure assigns the Root Port Configuration Space address windows to encompass the valid BAR address ranges.
  5. The ebfm_cfg_rp_ep procedure enables master transactions, memory address decoding, and I/O address decoding in the Endpoint PCIe* control register.

The ebfm_cfg_rp_ep procedure also sets up a bar_table data structure in BFM shared memory that lists the sizes and assigned addresses of all Endpoint BARs. This area of BFM shared memory is write-protected. Consequently, any application logic write accesses to this area cause a fatal simulation error.

BFM procedure calls to generate full PCIe* addresses for read and write requests to particular offsets from a BAR use this data structure. This procedure allows the testbench code that accesses the Endpoint application logic to use offsets from a BAR and avoid tracking specific addresses assigned to the BAR. The following table shows how to use those offsets.

Table 80.  BAR Table Structure

Offset (Bytes)

Description

+0

PCI Express address in BAR0

+4

PCI Express address in BAR1

+8

PCI Express address in BAR2

+12

PCI Express address in BAR3

+16

PCI Express address in BAR4

+20

PCI Express address in BAR5

+24

PCI Express address in Expansion ROM BAR

+28

Reserved

+32

BAR0 read back value after being written with all 1’s (used to compute size)

+36

BAR1 read back value after being written with all 1’s

+40

BAR2 read back value after being written with all 1’s

+44

BAR3 read back value after being written with all 1’s

+48

BAR4 read back value after being written with all 1’s

+52

BAR5 read back value after being written with all 1’s

+56

Expansion ROM BAR read back value after being written with all 1’s

+60

Reserved

The configuration routine does not configure any advanced PCI Express capabilities such as the AER capability.

Besides the ebfm_cfg_rp_ep procedure in altpcietb_bfm_rp_gen3_x8.sv, routines to read and write Endpoint Configuration Space registers directly are available in the Verilog HDL include file. After the ebfm_cfg_rp_ep procedure runs the PCI Express I/O and Memory Spaces have the layout shown in the following three figures. The memory space layout depends on the value of the addr_map_4GB_limit input parameter. The following figure shows the resulting memory space map when the addr_map_4GB_limit is 1.

Figure 73. Memory Space Layout—4 GB Limit

The following figure shows the resulting memory space map when the addr_map_4GB_limit is 0.

Figure 74. Memory Space Layout—No Limit

The following figure shows the I/O address space.

Figure 75. I/O Address Space
Level Two Title