Arria® 10 and Cyclone® 10 GX Avalon® Streaming Interface for PCI Express* User Guide

Download PDF
ID 683647
Date 9/11/2024
Public
Document Table of Contents
Document Table of Contents x
1. Datasheet 2. Quick Start Guide 3. Arria® 10 or Cyclone® 10 GX Parameter Settings 4. Physical Layout 5. Interfaces and Signal Descriptions 6. Registers 7. Reset and Clocks 8. Interrupts 9. Error Handling 10. PCI Express Protocol Stack 11. Transaction Layer Protocol (TLP) Details 12. Throughput Optimization 13. Design Implementation 14. Additional Features 15. Hard IP Reconfiguration 16. Testbench and Design Example 17. Debugging A. Transaction Layer Packet (TLP) Header Formats B. Lane Initialization and Reversal C. Arria® 10 or Cyclone® 10 GX Avalon-ST Interface for PCIe Solutions User Guide Archive D. Document Revision History
1. Datasheet x
1.1. Arria® 10 or Cyclone® 10 GX Avalon-ST Interface for PCI Express* Datasheet 1.2. Release Information 1.3. Device Family Support 1.4. Configurations 1.5. Debug Features 1.6. IP Core Verification 1.7. Resource Utilization 1.8. Recommended Speed Grades 1.9. Creating a Design for PCI Express
1.1. Arria® 10 or Cyclone® 10 GX Avalon-ST Interface for PCI Express* Datasheet x
1.1.1. Arria® 10 or Cyclone® 10 GX Features
1.6. IP Core Verification x
1.6.1. Compatibility Testing Environment
2. Quick Start Guide x
2.1. Directory Structure 2.2. Design Components 2.3. Generating the Design 2.4. Simulating the Design 2.5. Compiling and Testing the Design in Hardware
3. Arria® 10 or Cyclone® 10 GX Parameter Settings x
3.1. Parameters 3.2. Arria® 10 or Cyclone® 10 GX Avalon-ST Settings 3.3. Base Address Register (BAR) and Expansion ROM Settings 3.4. Base and Limit Registers for Root Ports 3.5. Device Identification Registers 3.6. PCI Express and PCI Capabilities Parameters 3.7. Vendor Specific Extended Capability (VSEC) 3.8. Configuration, Debug, and Extension Options 3.9. PHY Characteristics 3.10. Example Designs
3.6. PCI Express and PCI Capabilities Parameters x
3.6.1. PCI Express and PCI Capabilities 3.6.2. Error Reporting 3.6.3. Link Capabilities 3.6.4. MSI and MSI-X Capabilities 3.6.5. Slot Capabilities 3.6.6. Power Management
4. Physical Layout x
4.1. Hard IP Block Placement In Cyclone® 10 GX Devices 4.2. Hard IP Block Placement In Arria® 10 Devices 4.3. Channel and Pin Placement for the Gen1, Gen2, and Gen3 Data Rates 4.4. Channel Placement and fPLL and ATX PLL Usage for the Gen3 Data Rate 4.5. PCI Express Gen3 Bank Usage Restrictions
5. Interfaces and Signal Descriptions x
5.1. Clock Signals 5.2. Reset, Status, and Link Training Signals 5.3. ECRC Forwarding 5.4. Error Signals 5.5. Interrupts for Endpoints 5.6. Interrupts for Root Ports 5.7. Completion Side Band Signals 5.8. Parity Signals 5.9. LMI Signals 5.10. Transaction Layer Configuration Space Signals 5.11. Hard IP Reconfiguration Interface 5.12. Power Management Signals 5.13. Physical Layer Interface Signals
5.10. Transaction Layer Configuration Space Signals x
5.10.1. Configuration Space Register Access Timing 5.10.2. Configuration Space Register Access
5.13. Physical Layer Interface Signals x
5.13.1. Serial Data Signals 5.13.2. PIPE Interface Signals 5.13.3. Test Signals 5.13.4. Arria® 10 Development Kit Conduit Interface
6. Registers x
6.1. Correspondence between Configuration Space Registers and the PCIe Specification 6.2. Type 0 Configuration Space Registers 6.3. Type 1 Configuration Space Registers 6.4. PCI Express Capability Structures 6.5. Intel-Defined VSEC Registers 6.6. Advanced Error Reporting Capability
6.5. Intel-Defined VSEC Registers x
6.5.1. CvP Registers
6.6. Advanced Error Reporting Capability x
6.6.1. Uncorrectable Internal Error Mask Register 6.6.2. Uncorrectable Internal Error Status Register 6.6.3. Correctable Internal Error Mask Register 6.6.4. Correctable Internal Error Status Register
7. Reset and Clocks x
7.1. Reset Sequence for Hard IP for PCI Express IP Core and Application Layer 7.2. Clocks
7.2. Clocks x
7.2.1. Clock Domains 7.2.2. Clock Summary
7.2.1. Clock Domains x
7.2.1.1. coreclkout_hip 7.2.1.2. pld_clk
8. Interrupts x
8.1. Interrupts for Endpoints 8.2. Interrupts for Root Ports
8.1. Interrupts for Endpoints x
8.1.1. MSI and Legacy Interrupts 8.1.2. MSI-X 8.1.3. Implementing MSI-X Interrupts 8.1.4. Legacy Interrupts
9. Error Handling x
9.1. Physical Layer Errors 9.2. Data Link Layer Errors 9.3. Transaction Layer Errors 9.4. Error Reporting and Data Poisoning 9.5. Uncorrectable and Correctable Error Status Bits
10. PCI Express Protocol Stack x
10.1. Top-Level Interfaces 10.2. Transaction Layer 10.3. Data Link Layer 10.4. Physical Layer
10.1. Top-Level Interfaces x
10.1.1. Avalon-ST Interface 10.1.2. Clocks and Reset 10.1.3. Local Management Interface (LMI Interface) 10.1.4. Hard IP Reconfiguration 10.1.5. Interrupts 10.1.6. PIPE
10.2. Transaction Layer x
10.2.1. Configuration Space
11. Transaction Layer Protocol (TLP) Details x
11.1. Supported Message Types 11.2. Transaction Layer Routing Rules 11.3. Receive Buffer Reordering
11.1. Supported Message Types x
11.1.1. INTX Messages 11.1.2. Power Management Messages 11.1.3. Error Signaling Messages 11.1.4. Locked Transaction Message 11.1.5. Slot Power Limit Message 11.1.6. Vendor-Defined Messages 11.1.7. Hot Plug Messages
11.3. Receive Buffer Reordering x
11.3.1. Using Relaxed Ordering
12. Throughput Optimization x
12.1. Throughput of Posted Writes 12.2. Throughput of Non-Posted Reads
13. Design Implementation x
13.1. Making Pin Assignments to Assign I/O Standard to Serial Data Pins 13.2. Recommended Reset Sequence to Avoid Link Training Issues 13.3. SDC Timing Constraints
14. Additional Features x
14.1. Configuration over Protocol (CvP) 14.2. Autonomous Mode 14.3. ECRC
14.2. Autonomous Mode x
14.2.1. Enabling Autonomous Mode 14.2.2. Enabling CvP Initialization
14.3. ECRC x
14.3.1. ECRC on the RX Path 14.3.2. ECRC on the TX Path
16. Testbench and Design Example x
16.1. Endpoint Testbench 16.2. Test Driver Module 16.3. Root Port BFM Overview 16.4. BFM Procedures and Functions
16.1. Endpoint Testbench x
16.1.1. Endpoint Testbench for SR-IOV
16.3. Root Port BFM Overview x
16.3.1. BFM Memory Map 16.3.2. Configuration Space Bus and Device Numbering 16.3.3. Configuration of Root Port and Endpoint 16.3.4. Issuing Read and Write Transactions to the Application Layer
16.4. BFM Procedures and Functions x
16.4.1. ebfm_barwr Procedure 16.4.2. ebfm_barwr_imm Procedure 16.4.3. ebfm_barrd_wait Procedure 16.4.4. ebfm_barrd_nowt Procedure 16.4.5. ebfm_cfgwr_imm_wait Procedure 16.4.6. ebfm_cfgwr_imm_nowt Procedure 16.4.7. ebfm_cfgrd_wait Procedure 16.4.8. ebfm_cfgrd_nowt Procedure 16.4.9. BFM Configuration Procedures 16.4.10. BFM Shared Memory Access Procedures 16.4.11. BFM Log and Message Procedures 16.4.12. Verilog HDL Formatting Functions
16.4.9. BFM Configuration Procedures x
16.4.9.1. ebfm_cfg_rp_ep Procedure 16.4.9.2. ebfm_cfg_decode_bar Procedure
16.4.10. BFM Shared Memory Access Procedures x
16.4.10.1. Shared Memory Constants 16.4.10.2. shmem_write Task 16.4.10.3. shmem_read Function 16.4.10.4. shmem_display Verilog HDL Function 16.4.10.5. shmem_fill Procedure 16.4.10.6. shmem_chk_ok Function
16.4.11. BFM Log and Message Procedures x
16.4.11.1. ebfm_display Verilog HDL Function 16.4.11.2. ebfm_log_stop_sim Verilog HDL Function 16.4.11.3. ebfm_log_set_suppressed_msg_mask Task 16.4.11.4. ebfm_log_set_stop_on_msg_mask Verilog HDL Task 16.4.11.5. ebfm_log_open Verilog HDL Function 16.4.11.6. ebfm_log_close Verilog HDL Function
16.4.12. Verilog HDL Formatting Functions x
16.4.12.1. himage1 16.4.12.2. himage2 16.4.12.3. himage4 16.4.12.4. himage8 16.4.12.5. himage16 16.4.12.6. dimage1 16.4.12.7. dimage2 16.4.12.8. dimage3 16.4.12.9. dimage4 16.4.12.10. dimage5 16.4.12.11. dimage6 16.4.12.12. dimage7
17. Debugging x
17.1. Simulation Fails To Progress Beyond Polling.Active State 17.2. Hardware Bring-Up Issues 17.3. Link Training 17.4. Creating a Signal Tap Debug File to Match Your Design Hierarchy 17.5. Use Third-Party PCIe Analyzer 17.6. BIOS Enumeration Issues
17.3. Link Training x
17.3.1. Link Hangs in L0 State
A. Transaction Layer Packet (TLP) Header Formats x
A.1. TLP Packet Formats without Data Payload A.2. TLP Packet Formats with Data Payload
D. Document Revision History x
D.1. Document Revision History of the Arria® 10 or Cyclone® 10 GX Avalon® Streaming (Avalon-ST) Interface for PCIe* Solutions User Guide
1. Datasheet
2. Quick Start Guide
3. Arria® 10 or Cyclone® 10 GX Parameter Settings
4. Physical Layout
5. Interfaces and Signal Descriptions
6. Registers
7. Reset and Clocks
8. Interrupts
9. Error Handling
10. PCI Express Protocol Stack
11. Transaction Layer Protocol (TLP) Details
12. Throughput Optimization
13. Design Implementation
14. Additional Features
15. Hard IP Reconfiguration
16. Testbench and Design Example
17. Debugging
A. Transaction Layer Packet (TLP) Header Formats
B. Lane Initialization and Reversal
C. Arria® 10 or Cyclone® 10 GX Avalon-ST Interface for PCIe Solutions User Guide Archive
D. Document Revision History

16. Testbench and Design Example

This chapter introduces the Endpoint design example including a testbench, BFM, and a test driver module. You can create this design example using design flows described in Quick Start Guide.

When configured as an Endpoint variation, the testbench instantiates a design example and a Root Port BFM which provides the following functions:

  • A configuration routine that sets up all the basic configuration registers in the Endpoint. This configuration allows the Endpoint application to be the target and initiator of PCI Express transactions.
  • A Verilog HDL procedure interface to initiate PCI Express* transactions to the Endpoint.
  • A configuration routine that sets up all the basic configuration registers in the Root Port and the Endpoint BFM. This configuration allows the Endpoint application to be the target and initiator of PCI Express transactions.
  • A Verilog HDL procedure interface to initiate PCI Express transactions to the Endpoint BFM.

This testbench simulates a single Endpoint DUT.

The testbench uses a test driver module, altpcietb_bfm_rp_<gen>_x8.sv, to exercise the target memory. At startup, the test driver module displays information from the Root Port Configuration Space registers, so that you can correlate to the parameters you specified using the parameter editor.

Note: The Intel testbench and Root Port BFM provide a simple method to do basic testing of the Application Layer logic that interfaces to the variation. This BFM allows you to create and run simple task stimuli with configurable parameters to exercise basic functionality of the Intel example design. The testbench and Root Port BFM are not intended to be a substitute for a full verification environment. Corner cases and certain traffic profile stimuli are not covered. Refer to the items listed below for further details. To ensure the best verification coverage possible, Intel suggests strongly that you obtain commercially available PCI Express* verification IP and tools, or do your own extensive hardware testing or both.

Your Application Layer design may need to handle at least the following scenarios that are not possible to create with the Intel testbench and the Root Port BFM:

  • It is unable to generate or receive Vendor Defined Messages. Some systems generate Vendor Defined Messages. Consequently, you must design the Application Layer to process them. The Hard IP block passes these messages on to the Application Layer which, in most cases should ignore them.
  • It can only handle received read requests that are less than or equal to the currently set Maximum payload size option specified under PCI Express/PCI Capabilities heading under the Device tab using the parameter editor. Many systems are capable of handling larger read requests that are then returned in multiple completions.
  • It always returns a single completion for every read request. Some systems split completions on every 64-byte address boundary.
  • It always returns completions in the same order the read requests were issued. Some systems generate the completions out-of-order.
  • It is unable to generate zero-length read requests that some systems generate as flush requests following some write transactions. The Application Layer must be capable of generating the completions to the zero length read requests.
  • It uses fixed credit allocation.
  • It does not support parity.
  • It does not support multi-function designs.
  • It does not support Single Root I/O Virtualization (SR-IOV).

Section Content
Endpoint Testbench
Test Driver Module
Root Port BFM Overview
BFM Procedures and Functions

Level Two Title