Visible to Intel only — GUID: yid1574138934765
Ixiasoft
2.1.1. Directory Structure
2.1.2. Generating the Design
2.1.3. Simulating the E-Tile Hard IP for Ethernet Intel FPGA IP Design Example Testbench
2.1.4. Compiling the Compilation-Only Project
2.1.5. Compiling and Configuring the Design Example in Hardware
2.1.6. Testing the E-Tile Hard IP for Ethernet Intel FPGA IP Hardware Design Example
2.2.1.1. Non-PTP 10GE/25GE MAC+PCS with Optional RS-FEC Simulation Design Example
2.2.1.2. PTP 10GE/25GE MAC+PCS with Optional RS-FEC Simulation Design Example
2.2.1.3. 10GE/25GE PCS Only, OTN, or FlexE with Optional RS-FEC Simulation Design Example
2.2.1.4. 10GE/25GE Custom PCS with Optional RS-FEC Simulation Design Example
2.3.1. Simulation Design Examples
2.3.2. Hardware Design Examples
2.3.3. 100GE MAC+PCS with Optional RS-FEC Design Example Interface Signals
2.3.4. 100GE PCS with Optional RS-FEC Design Example Interface Signals
2.3.5. Multiple 25G Synchronous Ethernet Channels
2.3.6. 100GE MAC+PCS with Optional RS-FEC Design Example Registers
2.3.7. 100GE PCS with Optional RS-FEC Design Example Registers
2.3.1.1. Non-PTP E-Tile Hard IP for Ethernet Intel FPGA IP 100GE MAC+PCS with Optional RS-FEC Simulation Design Example
2.3.1.2. E-Tile Hard IP for Ethernet Intel FPGA IP 100GE MAC+PCS with Optional RS-FEC and PTP Simulation Design Example
2.3.1.3. E-Tile Hard IP for Ethernet Intel FPGA IP 100GE PCS Only with Optional RS-FEC Simulation Design Example
2.3.1.4. E-Tile Hard IP for Ethernet Intel FPGA IP 100GE OTN with Optional RS-FEC Simulation Design Example
2.3.1.5. E-Tile Hard IP for Ethernet Intel FPGA IP 100GE FlexE with Optional RS-FEC Simulation Design Example
2.3.2.1. 100GE MAC+PCS with Optional RS-FEC and PMA Adaptation Flow Hardware Design Example Components
2.3.2.2. 100GE MAC+PCS with Optional RS-FEC and PTP Hardware Design Example
2.3.2.3. 100GE PCS with Optional RS-FEC Hardware Design Example Components
2.3.2.4. Ethernet Adaptation Flow for 100G (CAUI-2) PAM4 <---> 100G (CAUI-4) NRZ Dynamic Reconfiguration Design Example
3.1.1. Hardware and Software Requirements
3.1.2. Generating the Design
3.1.3. Directory Structure
3.1.4. Simulating the Design Example Testbench
3.1.5. Compiling the Compilation-Only Project
3.1.6. Compiling and Configuring the Design Example in Hardware
3.1.7. Testing the E-tile CPRI PHY Intel® FPGA IP Hardware Design Example
4.1. Quick Start Guide
4.2. 10G/25G Ethernet Dynamic Reconfiguration Design Examples
4.3. CPRI Dynamic Reconfiguration Design Examples
4.4. 25G Ethernet to CPRI Dynamic Reconfiguration Design Example
4.5. 100G Ethernet Dynamic Reconfiguration Design Example
4.6. Document Revision History for the E-Tile Dynamic Reconfiguration Design Example
4.5.1. Functional Description
4.5.2. Testing the 100G Ethernet Dynamic Reconfiguration Hardware Design Example
4.5.3. Simulation Design Examples
4.5.4. 100GE DR Hardware Design Examples
4.5.5. 100G Ethernet Dynamic Reconfiguration Design Example Interface Signals
4.5.6. 100G Ethernet Dynamic Reconfiguration Examples Registers
4.5.7. Steps to Enable FEC
4.5.8. Steps to Disable FEC
Visible to Intel only — GUID: yid1574138934765
Ixiasoft
4.5.4. 100GE DR Hardware Design Examples
This section describes high-level flow guidelines for the E-tile reconfigurable Ethernet core.
You can follow these steps to configure the E-tile reconfigurable Ethernet IP core:
- Create a hardware project.
- Instantiate the E-Tile Dynamic Reconfiguration Design Example for 100G Ethernet protocol.
- Configure the IP parameters and generate design in the Quartus® Prime.
- Reconfigure the hardware project as needed during the run time.
- Define next configuration by programing CSR registers.
- Trigger the reconfiguration. Both variants, four 25G and one 100G Ethernet, are supported.
- Repeat step 2.