Low Latency 100G Ethernet Intel® Stratix® 10 FPGA IP Design Example User Guide

Download PDF
ID 683505
Date 1/27/2021
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Quick Start Guide 2. Design Example Description 3. Ethernet Toolkit Overview 4. Low Latency 100G Ethernet Intel Stratix 10 FPGA IP Design Example User Guide Archives 5. Document Revision History for the Low Latency 100G Ethernet Intel® Stratix® 10 FPGA IP Design Example User Guide
1. Quick Start Guide x
1.1. Directory Structure 1.2. Simulation Design Example Components 1.3. Hardware Design Example Components 1.4. Generating the Design 1.5. Simulating the Design Example Testbench 1.6. Compiling the Compilation-Only Project 1.7. Compiling and Configuring the Design Example in Hardware 1.8. Testing the Hardware Design Example
1.8. Testing the Hardware Design Example x
1.8.1. Testing the Hardware Design Example using Ethernet Link Inspector 1.8.2. Testing the Hardware Design Example using Ethernet Toolkit
2. Design Example Description x
2.1. Features 2.2. Design Example Behavior 2.3. Design Example Interface Signals 2.4. Design Example Registers
2.4. Design Example Registers x
2.4.1. Packet Generator Programming Sequence
3. Ethernet Toolkit Overview x
3.1. Features
1. Quick Start Guide
2. Design Example Description
3. Ethernet Toolkit Overview
4. Low Latency 100G Ethernet Intel Stratix 10 FPGA IP Design Example User Guide Archives
5. Document Revision History for the Low Latency 100G Ethernet Intel® Stratix® 10 FPGA IP Design Example User Guide

1.5. Simulating the Design Example Testbench

Figure 7. Procedure

Follow these steps to simulate the testbench:

  1. Change to the testbench simulation directory <design_example_dir>/example_testbench.
  2. Run the simulation script for the supported simulator of your choice. The script compiles and runs the testbench in the simulator. Refer to the table Steps to Simulate the Testbench.
  3. Analyze the results. The successful testbench sends ten packets, receives ten packets, and displays "Testbench complete."
    Table 3.  Steps to Simulate the Testbench
    Simulator Instructions
    Mentor Graphics ModelSim* In the command line, type vsim -do run_vsim.do

    If you prefer to simulate without bringing up the ModelSim GUI, type vsim -c -do run_vsim.do

    Note: The ModelSim* - Intel® FPGA Edition simulator does not have the capacity to simulate this IP core. You must use another supported ModelSim simulator such as ModelSim* SE.
    Cadence NCSim In the command line, type sh run_ncsim.sh
    Cadence Xcelium* In the command line, type sh run_xcelium.sh
    Synopsys VCS* / VCS* MX In the command line, type sh run_vcs.sh or sh run_vcsmx.sh
    Note: run_vcs.sh is only available if you select Verilog as the Generated HDL Format. If RS-FEC is enabled or you select VHDL as the Generated HDL Format, you must simulate the testbench with a mixed language simulator using run_vcsmx.sh.

The successful test run displays output confirming the following behavior:

  1. Waiting for the ATX PLLs to lock.
  2. Waiting for RX transceiver reset to complete.
  3. Waiting for RX alignment.
  4. Sending ten packets.
  5. Receiving ten packets.
  6. Displaying Testbench complete.

The following sample output illustrates a successful simulation test run:

ATX PLLs Locked
***************************************************
***************  Transmit Ready   *****************
***************************************************
Waiting for the receiver to be ready
Receive transceivers are out of reset
Waiting for RX alignment
Rx Alignment Status Update 1/4: Word/Block lock is acquired over all virtual lanes
Rx Alignment Status Update 2/4: Virtual lanes Ordered
Rx Alignment Status Update 3/4: RX deskew lock acquired
Rx Alignment Status Update 4/4: RX alignment lock acquired
Rx is fully aligned with Tx
***************************************************
**************   Receive Ready   ******************
***************************************************
Transmitting test data
** Sending Packet           1...
** Sending Packet           2...
** Sending Packet           3...
** Sending Packet           4...
** Sending Packet           5...
** Sending Packet           6...
** Sending Packet           7...
** Sending Packet           8...
** Sending Packet           9...
** Sending Packet          10...
** Received Packet          1...
** Received Packet          2...
** Received Packet          3...
** Received Packet          4...
** Received Packet          5...
** Received Packet          6...
** Received Packet          7...
** Received Packet          8...
** Received Packet          9...
** Received Packet         10...
**
** Testbench complete.
**
*****************************************
Level Two Title