Cyclone® V Avalon® Memory-Mapped (Avalon-MM) Interface for PCI Express* Solutions User Guide

Download PDF
ID 683494
Date 10/24/2024
Public
Document Table of Contents
Document Table of Contents x
1. Datasheet 2. Getting Started with the Avalon-MM Cyclone V Hard IP for PCI Express 3. Parameter Settings 4. Interfaces and Signal Descriptions 5. Registers 6. Reset and Clocks 7. Interrupts for Endpoints 8. Error Handling A. PCI Express Protocol Stack 9. Design Implementation 10. Additional Features 11. Transceiver PHY IP Reconfiguration 12. Debugging B. Frequently Asked Questions for PCI Express C. Lane Initialization and Reversal D. Document Revision History
1. Datasheet x
1.1. Avalon-MM Interface for PCIe Datasheet 1.2. Features 1.3. Release Information 1.4. Device Family Support 1.5. Configurations 1.6. Example Designs 1.7. IP Core Verification 1.8. Performance and Resource Utilization 1.9. Recommended Speed Grades 1.10. Creating a Design for PCI Express
1.7. IP Core Verification x
1.7.1. Compatibility Testing Environment
2. Getting Started with the Avalon-MM Cyclone V Hard IP for PCI Express x
2.1. Running Platform Designer 2.2. Generating the Example Design 2.3. Running a Gate-Level Simulation 2.4. Simulating the Single DWord Design 2.5. Understanding Channel Placement Guidelines 2.6. Generating Synthesis Files 2.7. Compiling the Design in the Quartus® Prime Software 2.8. Programming a Device
3. Parameter Settings x
3.1. Avalon-MM System Settings 3.2. Base Address Register (BAR) Settings 3.3. Device Identification Registers 3.4. Device Capabilities 3.5. Error Reporting 3.6. Link Capabilities 3.7. MSI and MSI-X Capabilities 3.8. Power Management 3.9. Avalon Memory‑Mapped System Settings
4. Interfaces and Signal Descriptions x
4.1. 64- or 128-Bit Avalon-MM Interface to the Endpoint Application Layer 4.2. Clock Signals 4.3. Reset Signals 4.4. Hard IP Status 4.5. Interrupts for Endpoints when Multiple MSI/MSI-X Support Is Enabled 4.6. Physical Layer Interface Signals
4.1. 64- or 128-Bit Avalon-MM Interface to the Endpoint Application Layer x
4.1.1. 32-Bit Non-Bursting Avalon-MM Control Register Access (CRA) Slave Signals 4.1.2. Bursting and Non-Bursting Avalon® -MM Module Signals 4.1.3. 64- or 128-Bit Bursting TX Avalon-MM Slave Signals
4.6. Physical Layer Interface Signals x
4.6.1. Transceiver Reconfiguration 4.6.2. Hard IP Status Extension 4.6.3. Serial Interface Signals 4.6.4. PIPE Interface Signals 4.6.5. Test Signals
4.6.2. Hard IP Status Extension x
4.6.2.1. Configuration Space Register Access 4.6.2.2. Configuration Space Register Access Timing
4.6.3. Serial Interface Signals x
4.6.3.1. Physical Layout of Hard IP in Cyclone V Devices 4.6.3.2. Channel Placement in Cyclone V Devices
5. Registers x
5.1. Correspondence between Configuration Space Registers and the PCIe Specification 5.2. Type 0 Configuration Space Registers 5.3. Type 1 Configuration Space Registers 5.4. PCI Express Capability Structures 5.5. Intel-Defined VSEC Registers 5.6. CvP Registers 5.7. 64- or 128-Bit Avalon-MM Bridge Register Descriptions 5.8. Programming Model for Avalon-MM Root Port 5.9. Uncorrectable Internal Error Mask Register 5.10. Uncorrectable Internal Error Status Register 5.11. Correctable Internal Error Mask Register 5.12. Correctable Internal Error Status Register
5.7. 64- or 128-Bit Avalon-MM Bridge Register Descriptions x
5.7.1. Avalon-MM to PCI Express Interrupt Registers
5.7.1. Avalon-MM to PCI Express Interrupt Registers x
5.7.1.1. Avalon-MM to PCI Express Interrupt Status Registers 5.7.1.2. Avalon-MM to PCI Express Interrupt Enable Registers 5.7.1.3. PCI Express Mailbox Registers 5.7.1.4. Avalon-MM-to-PCI Express Address Translation Table 5.7.1.5. PCI Express to Avalon-MM Interrupt Status and Enable Registers for Endpoints 5.7.1.6. Avalon-MM Mailbox Registers 5.7.1.7. Control Register Access (CRA) Avalon-MM Slave Port
5.8. Programming Model for Avalon-MM Root Port x
5.8.1. Sending a Write TLP 5.8.2. Sending a Read TLP or Receiving a Non-Posted Completion TLP 5.8.3. Examples of Reading and Writing BAR0 Using the CRA Interface 5.8.4. PCI Express to Avalon-MM Interrupt Status and Enable Registers for Root Ports 5.8.5. Root Port TLP Data Registers
6. Reset and Clocks x
6.1. Reset Sequence for Hard IP for PCI Express IP Core and Application Layer 6.2. Clocks
6.2. Clocks x
6.2.1. Clock Domains 6.2.2. Clock Summary
6.2.1. Clock Domains x
6.2.1.1. pclk 6.2.1.2. coreclkout_hip 6.2.1.3. pld_clk
7. Interrupts for Endpoints x
7.1. Enabling MSI or Legacy Interrupts 7.2. Generation of Avalon-MM Interrupts 7.3. Interrupts for Endpoints Using the Avalon-MM Interface with Multiple MSI/MSI-X Support
8. Error Handling x
8.1. Physical Layer Errors 8.2. Data Link Layer Errors 8.3. Transaction Layer Errors 8.4. Error Reporting and Data Poisoning 8.5. Uncorrectable and Correctable Error Status Bits
A. PCI Express Protocol Stack x
A.1. Top-Level Interfaces A.2. Data Link Layer A.3. Physical Layer A.4. 32-Bit PCI Express Avalon-MM Bridge A.5. Completer Only Single Dword Endpoint
A.1. Top-Level Interfaces x
A.1.1. Avalon-MM Interface A.1.2. Clocks and Reset A.1.3. Transceiver Reconfiguration A.1.4. Interrupts A.1.5. PIPE
A.4. 32-Bit PCI Express Avalon-MM Bridge x
A.4.1. Avalon‑MM Bridge TLPs A.4.2. Avalon-MM-to-PCI Express Write Requests A.4.3. Avalon-MM-to-PCI Express Upstream Read Requests A.4.4. PCI Express-to-Avalon-MM Read Completions A.4.5. PCI Express-to-Avalon-MM Downstream Write Requests A.4.6. PCI Express-to-Avalon-MM Downstream Read Requests A.4.7. Avalon-MM-to-PCI Express Read Completions A.4.8. PCI Express-to-Avalon-MM Address Translation for 32-Bit Bridge A.4.9. Minimizing BAR Sizes and the PCIe Address Space A.4.10. Avalon® -MM-to-PCI Express Address Translation Algorithm for 32-Bit Addressing
A.5. Completer Only Single Dword Endpoint x
A.5.1. RX Block A.5.2. Avalon-MM RX Master Block A.5.3. TX Block A.5.4. Interrupt Handler Block
9. Design Implementation x
9.1. Making Analog QSF Assignments Using the Assignment Editor 9.2. Making Pin Assignments 9.3. Recommended Reset Sequence to Avoid Link Training Issues
10. Additional Features x
10.1. Configuration over Protocol (CvP) 10.2. Autonomous Mode 10.3. ECRC
10.2. Autonomous Mode x
10.2.1. Enabling Autonomous Mode 10.2.2. Enabling CvP Initialization
10.3. ECRC x
10.3.1. ECRC on the RX Path 10.3.2. ECRC on the TX Path
11. Transceiver PHY IP Reconfiguration x
11.1. Connecting the Transceiver Reconfiguration Controller IP Core 11.2. Transceiver Reconfiguration Controller Connectivity for Designs Using CvP
12. Debugging x
12.1. Hardware Bring-Up Issues 12.2. Link Training 12.3. Use Third-Party PCIe Analyzer 12.4. BIOS Enumeration Issues
D. Document Revision History x
D.1. Arria® V and Cyclone® V Avalon® Memory Mapped (Avalon-MM) Interface for PCIe* Solutions User Guide Revision History
1. Datasheet
2. Getting Started with the Avalon-MM Cyclone V Hard IP for PCI Express
3. Parameter Settings
4. Interfaces and Signal Descriptions
5. Registers
6. Reset and Clocks
7. Interrupts for Endpoints
8. Error Handling
A. PCI Express Protocol Stack
9. Design Implementation
10. Additional Features
11. Transceiver PHY IP Reconfiguration
12. Debugging
B. Frequently Asked Questions for PCI Express
C. Lane Initialization and Reversal
D. Document Revision History

4.6.4. PIPE Interface Signals

These PIPE signals are available for Gen1 and Gen2 variants so that you can simulate using either the serial or the PIPE interface. Simulation is much faster using the PIPE interface because the PIPE simulation bypasses the SERDES model . By default, the PIPE interface is 8 bits for Gen1 and Gen2. You can use the PIPE interface for simulation even though your actual design includes a serial interface to the internal transceivers. However, it is not possible to use the Hard IP PIPE interface in hardware, including probing these signals using Signal Tap II Embedded Logic Analyzer.

Table 32.  PIPE Interface Signals In the following table, signals that include lane number 0 also exist for other lanes.

Signal

Direction

Description

txdata0[7:0]

Output

Transmit data <n> (2 symbols on lane <n>). This bus transmits data on lane <n>.

txdatak0

Output

Transmit data control <n>. This signal serves as the control bit for txdata <n>.

txdetectrx0

Output

Transmit detect receive <n>. This signal tells the PHY layer to start a receive detection operation or to begin loopback.

txelecidle0

Output

Transmit electrical idle <n>. This signal forces the TX output to electrical idle.

txcompl0

Output

Transmit compliance <n>. This signal forces the running disparity to negative in Compliance Mode (negative COM character).

rxpolarity0

Output

Receive polarity <n>. This signal instructs the PHY layer to invert the polarity of the 8B/10B receiver decoding block.

powerdown0[1:0]

Output

Power down <n>. This signal requests the PHY to change its power state to the specified state (P0, P0s, P1, or P2).

tx_deemph0

Output

Transmit de-emphasis selection. The Cyclone V Hard IP for PCI Express sets the value for this signal based on the indication received from the other end of the link during the Training Sequences (TS). You do not need to change this value.

rxdata0[7:0]  (1)

Input

Receive data <n> (2 symbols on lane <n>). This bus receives data on lane <n>.

rxdatak0  (1)

Input

Receive data >n>. This bus receives data on lane <n>.

rxvalid0  (1)

Input

Receive valid <n>. This signal indicates symbol lock and valid data on rxdata <n> and rxdatak <n>.

phystatus0 (1)

Input

PHY status <n>. This signal communicates completion of several PHY requests.

eidleinfersel0[2:0]

Output

Electrical idle entry inference mechanism selection. The following encodings are defined:

  • 3'b0xx: Electrical Idle Inference not required in current LTSSM state
  • 3'b100: Absence of COM/SKP Ordered Set in the 128 us window for Gen1 or Gen2
  • 3'b101: Absence of TS1/TS2 Ordered Set in a 1280 UI interval for Gen1 or Gen2
  • 3'b110: Absence of Electrical Idle Exit in 2000 UI interval for Gen1 and 16000 UI interval for Gen2
  • 3'b111: Absence of Electrical idle exit in 128 us window for Gen1

rxelecidle0 (1)

Input

Receive electrical idle <n>. When asserted, indicates detection of an electrical idle.

rxstatus0[2:0] (1)

Input

Receive status <n>. This signal encodes receive status and error codes for the receive data stream and receiver detection.

sim_pipe_ltssmstate0[4:0]

Input and Output

LTSSM state: The LTSSM state machine encoding defines the following states:

  • 5’b00000: Detect.Quiet
  • 5’b 00001: Detect.Active
  • 5’b00010: Polling.Active
  • 5’b 00011: Polling.Compliance
  • 5’b 00100: Polling.Configuration
  • 5’b00101: Polling.Speed
  • 5’b00110: config.LinkwidthsStart
  • 5’b 00111: Config.Linkaccept
  • 5’b 01000: Config.Lanenumaccept
  • 5’b01001: Config.Lanenumwait
  • 5’b01010: Config.Complete
  • 5’b 01011: Config.Idle
  • 5’b01100: Recovery.Rcvlock
  • 5’b01101: Recovery.Rcvconfig
  • 5’b01110: Recovery.Idle
  • 5’b 01111: L0
  • 5’b10000: Disable
  • 5’b10001: Loopback.Entry
  • 5’b10010: Loopback.Active
  • 5’b10011: Loopback.Exit
  • 5’b10100: Hot.Reset
  • 5’b10101: LOs
  • 5’b11001: L2.transmit.Wake
  • 5’b11010: Recovery.Speed
  • 5’b11011: Recovery.Equalization, Phase 0
  • 5’b11100: Recovery.Equalization, Phase 1
  • 5’b11101: Recovery.Equalization, Phase 2
  • 5’b11110: Recovery.Equalization, Phase 3
  • 5’b11111: Recovery.Equalization, Done
sim_pipe_rate[1:0]

Output

The 2‑bit encodings have the following meanings:

  • 2’b00: Gen1 rate (2.5 Gbps)
  • 2’b01: Gen2 rate (5.0 Gbps)
  • 2’b1X: Gen3 rate (8.0 Gbps)
sim_pipe_pclk_in

Input

This clock is used for PIPE simulation only, and is derived from the refclk. It is the PIPE interface clock used for PIPE mode simulation.

txswing0

Output

When asserted, indicates full swing for the transmitter voltage. When deasserted indicates half swing.

tx_margin0[2:0]

Output

Transmit VOD margin selection. The value for this signal is based on the value from the Link Control 2 Register. Available for simulation only.

Notes:

  1. These signals are for simulation only. For Quartus® Prime software compilation, these pipe signals can be left floating.
Level Two Title