Cyclone® V Avalon® Memory-Mapped (Avalon-MM) Interface for PCI Express* Solutions User Guide

Download PDF
ID 683494
Date 10/24/2024
Public
Document Table of Contents
Document Table of Contents x
1. Datasheet 2. Getting Started with the Avalon-MM Cyclone V Hard IP for PCI Express 3. Parameter Settings 4. Interfaces and Signal Descriptions 5. Registers 6. Reset and Clocks 7. Interrupts for Endpoints 8. Error Handling A. PCI Express Protocol Stack 9. Design Implementation 10. Additional Features 11. Transceiver PHY IP Reconfiguration 12. Debugging B. Frequently Asked Questions for PCI Express C. Lane Initialization and Reversal D. Document Revision History
1. Datasheet x
1.1. Avalon-MM Interface for PCIe Datasheet 1.2. Features 1.3. Release Information 1.4. Device Family Support 1.5. Configurations 1.6. Example Designs 1.7. IP Core Verification 1.8. Performance and Resource Utilization 1.9. Recommended Speed Grades 1.10. Creating a Design for PCI Express
1.7. IP Core Verification x
1.7.1. Compatibility Testing Environment
2. Getting Started with the Avalon-MM Cyclone V Hard IP for PCI Express x
2.1. Running Platform Designer 2.2. Generating the Example Design 2.3. Running a Gate-Level Simulation 2.4. Simulating the Single DWord Design 2.5. Understanding Channel Placement Guidelines 2.6. Generating Synthesis Files 2.7. Compiling the Design in the Quartus® Prime Software 2.8. Programming a Device
3. Parameter Settings x
3.1. Avalon-MM System Settings 3.2. Base Address Register (BAR) Settings 3.3. Device Identification Registers 3.4. Device Capabilities 3.5. Error Reporting 3.6. Link Capabilities 3.7. MSI and MSI-X Capabilities 3.8. Power Management 3.9. Avalon Memory‑Mapped System Settings
4. Interfaces and Signal Descriptions x
4.1. 64- or 128-Bit Avalon-MM Interface to the Endpoint Application Layer 4.2. Clock Signals 4.3. Reset Signals 4.4. Hard IP Status 4.5. Interrupts for Endpoints when Multiple MSI/MSI-X Support Is Enabled 4.6. Physical Layer Interface Signals
4.1. 64- or 128-Bit Avalon-MM Interface to the Endpoint Application Layer x
4.1.1. 32-Bit Non-Bursting Avalon-MM Control Register Access (CRA) Slave Signals 4.1.2. Bursting and Non-Bursting Avalon® -MM Module Signals 4.1.3. 64- or 128-Bit Bursting TX Avalon-MM Slave Signals
4.6. Physical Layer Interface Signals x
4.6.1. Transceiver Reconfiguration 4.6.2. Hard IP Status Extension 4.6.3. Serial Interface Signals 4.6.4. PIPE Interface Signals 4.6.5. Test Signals
4.6.2. Hard IP Status Extension x
4.6.2.1. Configuration Space Register Access 4.6.2.2. Configuration Space Register Access Timing
4.6.3. Serial Interface Signals x
4.6.3.1. Physical Layout of Hard IP in Cyclone V Devices 4.6.3.2. Channel Placement in Cyclone V Devices
5. Registers x
5.1. Correspondence between Configuration Space Registers and the PCIe Specification 5.2. Type 0 Configuration Space Registers 5.3. Type 1 Configuration Space Registers 5.4. PCI Express Capability Structures 5.5. Intel-Defined VSEC Registers 5.6. CvP Registers 5.7. 64- or 128-Bit Avalon-MM Bridge Register Descriptions 5.8. Programming Model for Avalon-MM Root Port 5.9. Uncorrectable Internal Error Mask Register 5.10. Uncorrectable Internal Error Status Register 5.11. Correctable Internal Error Mask Register 5.12. Correctable Internal Error Status Register
5.7. 64- or 128-Bit Avalon-MM Bridge Register Descriptions x
5.7.1. Avalon-MM to PCI Express Interrupt Registers
5.7.1. Avalon-MM to PCI Express Interrupt Registers x
5.7.1.1. Avalon-MM to PCI Express Interrupt Status Registers 5.7.1.2. Avalon-MM to PCI Express Interrupt Enable Registers 5.7.1.3. PCI Express Mailbox Registers 5.7.1.4. Avalon-MM-to-PCI Express Address Translation Table 5.7.1.5. PCI Express to Avalon-MM Interrupt Status and Enable Registers for Endpoints 5.7.1.6. Avalon-MM Mailbox Registers 5.7.1.7. Control Register Access (CRA) Avalon-MM Slave Port
5.8. Programming Model for Avalon-MM Root Port x
5.8.1. Sending a Write TLP 5.8.2. Sending a Read TLP or Receiving a Non-Posted Completion TLP 5.8.3. Examples of Reading and Writing BAR0 Using the CRA Interface 5.8.4. PCI Express to Avalon-MM Interrupt Status and Enable Registers for Root Ports 5.8.5. Root Port TLP Data Registers
6. Reset and Clocks x
6.1. Reset Sequence for Hard IP for PCI Express IP Core and Application Layer 6.2. Clocks
6.2. Clocks x
6.2.1. Clock Domains 6.2.2. Clock Summary
6.2.1. Clock Domains x
6.2.1.1. pclk 6.2.1.2. coreclkout_hip 6.2.1.3. pld_clk
7. Interrupts for Endpoints x
7.1. Enabling MSI or Legacy Interrupts 7.2. Generation of Avalon-MM Interrupts 7.3. Interrupts for Endpoints Using the Avalon-MM Interface with Multiple MSI/MSI-X Support
8. Error Handling x
8.1. Physical Layer Errors 8.2. Data Link Layer Errors 8.3. Transaction Layer Errors 8.4. Error Reporting and Data Poisoning 8.5. Uncorrectable and Correctable Error Status Bits
A. PCI Express Protocol Stack x
A.1. Top-Level Interfaces A.2. Data Link Layer A.3. Physical Layer A.4. 32-Bit PCI Express Avalon-MM Bridge A.5. Completer Only Single Dword Endpoint
A.1. Top-Level Interfaces x
A.1.1. Avalon-MM Interface A.1.2. Clocks and Reset A.1.3. Transceiver Reconfiguration A.1.4. Interrupts A.1.5. PIPE
A.4. 32-Bit PCI Express Avalon-MM Bridge x
A.4.1. Avalon‑MM Bridge TLPs A.4.2. Avalon-MM-to-PCI Express Write Requests A.4.3. Avalon-MM-to-PCI Express Upstream Read Requests A.4.4. PCI Express-to-Avalon-MM Read Completions A.4.5. PCI Express-to-Avalon-MM Downstream Write Requests A.4.6. PCI Express-to-Avalon-MM Downstream Read Requests A.4.7. Avalon-MM-to-PCI Express Read Completions A.4.8. PCI Express-to-Avalon-MM Address Translation for 32-Bit Bridge A.4.9. Minimizing BAR Sizes and the PCIe Address Space A.4.10. Avalon® -MM-to-PCI Express Address Translation Algorithm for 32-Bit Addressing
A.5. Completer Only Single Dword Endpoint x
A.5.1. RX Block A.5.2. Avalon-MM RX Master Block A.5.3. TX Block A.5.4. Interrupt Handler Block
9. Design Implementation x
9.1. Making Analog QSF Assignments Using the Assignment Editor 9.2. Making Pin Assignments 9.3. Recommended Reset Sequence to Avoid Link Training Issues
10. Additional Features x
10.1. Configuration over Protocol (CvP) 10.2. Autonomous Mode 10.3. ECRC
10.2. Autonomous Mode x
10.2.1. Enabling Autonomous Mode 10.2.2. Enabling CvP Initialization
10.3. ECRC x
10.3.1. ECRC on the RX Path 10.3.2. ECRC on the TX Path
11. Transceiver PHY IP Reconfiguration x
11.1. Connecting the Transceiver Reconfiguration Controller IP Core 11.2. Transceiver Reconfiguration Controller Connectivity for Designs Using CvP
12. Debugging x
12.1. Hardware Bring-Up Issues 12.2. Link Training 12.3. Use Third-Party PCIe Analyzer 12.4. BIOS Enumeration Issues
D. Document Revision History x
D.1. Arria® V and Cyclone® V Avalon® Memory Mapped (Avalon-MM) Interface for PCIe* Solutions User Guide Revision History
1. Datasheet
2. Getting Started with the Avalon-MM Cyclone V Hard IP for PCI Express
3. Parameter Settings
4. Interfaces and Signal Descriptions
5. Registers
6. Reset and Clocks
7. Interrupts for Endpoints
8. Error Handling
A. PCI Express Protocol Stack
9. Design Implementation
10. Additional Features
11. Transceiver PHY IP Reconfiguration
12. Debugging
B. Frequently Asked Questions for PCI Express
C. Lane Initialization and Reversal
D. Document Revision History

4.4. Hard IP Status

Refer to Reset and Clocks for more information about the reset sequence and a block diagram of the reset logic.

Table 23.  Status and Link Training Signals

Signal

Direction

Description

derr_cor_ext_rcv

Output

Indicates a corrected error in the RX buffer. This signal is for debug only. It is not valid until the RX buffer is filled with data. This is a pulse, not a level, signal. Internally, the pulse is generated with the 500 MHz clock. A pulse extender extends the signal so that the FPGA fabric running at 250 MHz can capture it. Because the error was corrected by the IP core, no Application Layer intervention is required. 3

derr_cor_ext_rpl

Output

Indicates a corrected ECC error in the retry buffer. This signal is for debug only. Because the error was corrected by the IP core, no Application Layer intervention is required. 3

derr_rpl

Output

Indicates an uncorrectable error in the retry buffer. This signal is for debug only. 3

The signal is not available for Arria V and Cyclone V devices.

dlup_exit

Output

This signal is asserted low for one pld_clk cycle when the IP core exits the DLCMSM DL_Up state, indicating that the Data Link Layer has lost communication with the other end of the PCIe link and left the Up state. When this pulse is asserted, the Application Layer should generate an internal reset signal that is asserted for at least 32 cycles.

ev128ns

Output

Asserted every 128 ns to create a time base aligned activity.

ev1us

Output

Asserted every 1µs to create a time base aligned activity.

hotrst_exit

Output

Hot reset exit. This signal is asserted for 1 clock cycle when the LTSSM exits the hot reset state. This signal should cause the Application Layer to be reset. This signal is active low. When this pulse is asserted, the Application Layer should generate an internal reset signal that is asserted for at least 32 cycles.

int_status[3:0]

Output

These signals drive legacy interrupts to the Application Layer as follows:

  • int_status[0]: interrupt signal A
  • int_status[1]: interrupt signal B
  • int_status[2]: interrupt signal C
  • int_status[3]: interrupt signal D
ko_cpl_spc_data[11:0]

Output

The Application Layer can use this signal to build circuitry to prevent RX buffer overflow for completion data. Endpoints must advertise infinite space for completion data; however, RX buffer space is finite. ko_cpl_spc_data is a static signal that reflects the total number of 16 byte completion data units that can be stored in the completion RX buffer.

ko_cpl_spc_header[7:0]

Output

The Application Layer can use this signal to build circuitry to prevent RX buffer overflow for completion headers. Endpoints must advertise infinite space for completion headers; however, RX buffer space is finite. ko_cpl_spc_header is a static signal that indicates the total number of completion headers that can be stored in the RX buffer.

l2_exit

Output

L2 exit. This signal is active low and otherwise remains high. It is asserted for one cycle (changing value from 1 to 0 and back to 1) after the LTSSM transitions from l2.idle to detect. When this pulse is asserted, the Application Layer should generate an internal reset signal that is asserted for at least 32 cycles.

lane_act[3:0]

Output

Lane Active Mode: This signal indicates the number of lanes that configured during link training. The following encodings are defined:

  • 4’b0001: 1 lane
  • 4’b0010: 2 lanes
  • 4’b0100: 4 lanes
  • 4’b1000: 8 lanes
ltssmstate[4:0]

Output

LTSSM state: The LTSSM state machine encoding defines the following states:

  • 00000: Detect.Quiet
  • 00001: Detect.Active
  • 00010: Polling.Active
  • 00011: Polling.Compliance
  • 00100: Polling.Configuration
  • 00101: Polling.Speed
  • 00110: config.Linkwidthstart
  • 00111: Config.Linkaccept
  • 01000: Config.Lanenumaccept
  • 01001: Config.Lanenumwait
  • 01010: Config.Complete
  • 01011: Config.Idle
  • 01100: Recovery.Rcvlock
  • 01101: Recovery.Rcvconfig
  • 01110: Recovery.Idle
  • 01111: L0
  • 10000: Disable
  • 10001: Loopback.Entry
  • 10010: Loopback.Active
  • 10011: Loopback.Exit
  • 10100: Hot.Reset
  • 10101: LOs
  • 11001: L2.transmit.Wake
  • 11010: Recovery.Speed
  • 11011: Recovery.Equalization, Phase 0
  • 11100: Recovery.Equalization, Phase 1
  • 11101: Recovery.Equalization, Phase 2
  • 11110: recovery.Equalization, Phase 3
Related Information
3 Debug signals are not rigorously verified and should only be used to observe behavior. Debug signals should not be used to drive custom logic.
Level Two Title