Cyclone® V Avalon® Memory-Mapped (Avalon-MM) Interface for PCI Express* Solutions User Guide

Download PDF
ID 683494
Date 10/24/2024
Public
Document Table of Contents
Document Table of Contents x
1. Datasheet 2. Getting Started with the Avalon-MM Cyclone V Hard IP for PCI Express 3. Parameter Settings 4. Interfaces and Signal Descriptions 5. Registers 6. Reset and Clocks 7. Interrupts for Endpoints 8. Error Handling A. PCI Express Protocol Stack 9. Design Implementation 10. Additional Features 11. Transceiver PHY IP Reconfiguration 12. Debugging B. Frequently Asked Questions for PCI Express C. Lane Initialization and Reversal D. Document Revision History
1. Datasheet x
1.1. Avalon-MM Interface for PCIe Datasheet 1.2. Features 1.3. Release Information 1.4. Device Family Support 1.5. Configurations 1.6. Example Designs 1.7. IP Core Verification 1.8. Performance and Resource Utilization 1.9. Recommended Speed Grades 1.10. Creating a Design for PCI Express
1.7. IP Core Verification x
1.7.1. Compatibility Testing Environment
2. Getting Started with the Avalon-MM Cyclone V Hard IP for PCI Express x
2.1. Running Platform Designer 2.2. Generating the Example Design 2.3. Running a Gate-Level Simulation 2.4. Simulating the Single DWord Design 2.5. Understanding Channel Placement Guidelines 2.6. Generating Synthesis Files 2.7. Compiling the Design in the Quartus® Prime Software 2.8. Programming a Device
3. Parameter Settings x
3.1. Avalon-MM System Settings 3.2. Base Address Register (BAR) Settings 3.3. Device Identification Registers 3.4. Device Capabilities 3.5. Error Reporting 3.6. Link Capabilities 3.7. MSI and MSI-X Capabilities 3.8. Power Management 3.9. Avalon Memory‑Mapped System Settings
4. Interfaces and Signal Descriptions x
4.1. 64- or 128-Bit Avalon-MM Interface to the Endpoint Application Layer 4.2. Clock Signals 4.3. Reset Signals 4.4. Hard IP Status 4.5. Interrupts for Endpoints when Multiple MSI/MSI-X Support Is Enabled 4.6. Physical Layer Interface Signals
4.1. 64- or 128-Bit Avalon-MM Interface to the Endpoint Application Layer x
4.1.1. 32-Bit Non-Bursting Avalon-MM Control Register Access (CRA) Slave Signals 4.1.2. Bursting and Non-Bursting Avalon® -MM Module Signals 4.1.3. 64- or 128-Bit Bursting TX Avalon-MM Slave Signals
4.6. Physical Layer Interface Signals x
4.6.1. Transceiver Reconfiguration 4.6.2. Hard IP Status Extension 4.6.3. Serial Interface Signals 4.6.4. PIPE Interface Signals 4.6.5. Test Signals
4.6.2. Hard IP Status Extension x
4.6.2.1. Configuration Space Register Access 4.6.2.2. Configuration Space Register Access Timing
4.6.3. Serial Interface Signals x
4.6.3.1. Physical Layout of Hard IP in Cyclone V Devices 4.6.3.2. Channel Placement in Cyclone V Devices
5. Registers x
5.1. Correspondence between Configuration Space Registers and the PCIe Specification 5.2. Type 0 Configuration Space Registers 5.3. Type 1 Configuration Space Registers 5.4. PCI Express Capability Structures 5.5. Intel-Defined VSEC Registers 5.6. CvP Registers 5.7. 64- or 128-Bit Avalon-MM Bridge Register Descriptions 5.8. Programming Model for Avalon-MM Root Port 5.9. Uncorrectable Internal Error Mask Register 5.10. Uncorrectable Internal Error Status Register 5.11. Correctable Internal Error Mask Register 5.12. Correctable Internal Error Status Register
5.7. 64- or 128-Bit Avalon-MM Bridge Register Descriptions x
5.7.1. Avalon-MM to PCI Express Interrupt Registers
5.7.1. Avalon-MM to PCI Express Interrupt Registers x
5.7.1.1. Avalon-MM to PCI Express Interrupt Status Registers 5.7.1.2. Avalon-MM to PCI Express Interrupt Enable Registers 5.7.1.3. PCI Express Mailbox Registers 5.7.1.4. Avalon-MM-to-PCI Express Address Translation Table 5.7.1.5. PCI Express to Avalon-MM Interrupt Status and Enable Registers for Endpoints 5.7.1.6. Avalon-MM Mailbox Registers 5.7.1.7. Control Register Access (CRA) Avalon-MM Slave Port
5.8. Programming Model for Avalon-MM Root Port x
5.8.1. Sending a Write TLP 5.8.2. Sending a Read TLP or Receiving a Non-Posted Completion TLP 5.8.3. Examples of Reading and Writing BAR0 Using the CRA Interface 5.8.4. PCI Express to Avalon-MM Interrupt Status and Enable Registers for Root Ports 5.8.5. Root Port TLP Data Registers
6. Reset and Clocks x
6.1. Reset Sequence for Hard IP for PCI Express IP Core and Application Layer 6.2. Clocks
6.2. Clocks x
6.2.1. Clock Domains 6.2.2. Clock Summary
6.2.1. Clock Domains x
6.2.1.1. pclk 6.2.1.2. coreclkout_hip 6.2.1.3. pld_clk
7. Interrupts for Endpoints x
7.1. Enabling MSI or Legacy Interrupts 7.2. Generation of Avalon-MM Interrupts 7.3. Interrupts for Endpoints Using the Avalon-MM Interface with Multiple MSI/MSI-X Support
8. Error Handling x
8.1. Physical Layer Errors 8.2. Data Link Layer Errors 8.3. Transaction Layer Errors 8.4. Error Reporting and Data Poisoning 8.5. Uncorrectable and Correctable Error Status Bits
A. PCI Express Protocol Stack x
A.1. Top-Level Interfaces A.2. Data Link Layer A.3. Physical Layer A.4. 32-Bit PCI Express Avalon-MM Bridge A.5. Completer Only Single Dword Endpoint
A.1. Top-Level Interfaces x
A.1.1. Avalon-MM Interface A.1.2. Clocks and Reset A.1.3. Transceiver Reconfiguration A.1.4. Interrupts A.1.5. PIPE
A.4. 32-Bit PCI Express Avalon-MM Bridge x
A.4.1. Avalon‑MM Bridge TLPs A.4.2. Avalon-MM-to-PCI Express Write Requests A.4.3. Avalon-MM-to-PCI Express Upstream Read Requests A.4.4. PCI Express-to-Avalon-MM Read Completions A.4.5. PCI Express-to-Avalon-MM Downstream Write Requests A.4.6. PCI Express-to-Avalon-MM Downstream Read Requests A.4.7. Avalon-MM-to-PCI Express Read Completions A.4.8. PCI Express-to-Avalon-MM Address Translation for 32-Bit Bridge A.4.9. Minimizing BAR Sizes and the PCIe Address Space A.4.10. Avalon® -MM-to-PCI Express Address Translation Algorithm for 32-Bit Addressing
A.5. Completer Only Single Dword Endpoint x
A.5.1. RX Block A.5.2. Avalon-MM RX Master Block A.5.3. TX Block A.5.4. Interrupt Handler Block
9. Design Implementation x
9.1. Making Analog QSF Assignments Using the Assignment Editor 9.2. Making Pin Assignments 9.3. Recommended Reset Sequence to Avoid Link Training Issues
10. Additional Features x
10.1. Configuration over Protocol (CvP) 10.2. Autonomous Mode 10.3. ECRC
10.2. Autonomous Mode x
10.2.1. Enabling Autonomous Mode 10.2.2. Enabling CvP Initialization
10.3. ECRC x
10.3.1. ECRC on the RX Path 10.3.2. ECRC on the TX Path
11. Transceiver PHY IP Reconfiguration x
11.1. Connecting the Transceiver Reconfiguration Controller IP Core 11.2. Transceiver Reconfiguration Controller Connectivity for Designs Using CvP
12. Debugging x
12.1. Hardware Bring-Up Issues 12.2. Link Training 12.3. Use Third-Party PCIe Analyzer 12.4. BIOS Enumeration Issues
D. Document Revision History x
D.1. Arria® V and Cyclone® V Avalon® Memory Mapped (Avalon-MM) Interface for PCIe* Solutions User Guide Revision History
1. Datasheet
2. Getting Started with the Avalon-MM Cyclone V Hard IP for PCI Express
3. Parameter Settings
4. Interfaces and Signal Descriptions
5. Registers
6. Reset and Clocks
7. Interrupts for Endpoints
8. Error Handling
A. PCI Express Protocol Stack
9. Design Implementation
10. Additional Features
11. Transceiver PHY IP Reconfiguration
12. Debugging
B. Frequently Asked Questions for PCI Express
C. Lane Initialization and Reversal
D. Document Revision History

3.4. Device Capabilities

Table 12.  Capabilities Registers

Parameter

Possible Values

Default Value

Description

Maximum payload size

128 bytes

256 bytes

128 bytes

Specifies the maximum payload size supported. This parameter sets the read-only value of the max payload size supported field of the Device Capabilities register (0x084[2:0]). Address: 0x084.

Completion timeout range

ABCD

BCD

ABC

AB

B

A

None

ABCD

Indicates device function support for the optional completion timeout programmability mechanism. This mechanism allows system software to modify the completion timeout value. This field is applicable only to Root Ports and Endpoints that issue requests on their own behalf. Completion timeouts are specified and enabled in the Device Control 2 register (0x0A8) of the PCI Express Capability Structure Version. For all other functions this field is reserved and must be hardwired to 0x0000b. Four time value ranges are defined:

  • Range A: 50 us to 10 ms
  • Range B: 10 ms to 250 ms
  • Range C: 250 ms to 4 s
  • Range D: 4 s to 64 s

Bits are set to show timeout value ranges supported. The function must implement a timeout value in the range 50 s to 50 ms. The following values specify the range:

  • None – Completion timeout programming is not supported
  • 0001 Range A
  • 0010 Range B
  • 0011 Ranges A and B
  • 0110 Ranges B and C
  • 0111 Ranges A, B, and C
  • 1110 Ranges B, C and D
  • 1111 Ranges A, B, C, and D

All other values are reserved. Altera recommends that the completion timeout mechanism expire in no less than 10 ms.

Implement completion timeout disable

On/Off

On

For Endpoints using PCI Express version 2.1 or 3.0, this option must be On. The timeout range is selectable. When On, the core supports the completion timeout disable mechanism via the PCI Express Device Control Register 2. The Application Layer logic must implement the actual completion timeout mechanism for the required ranges.

Level Two Title