Cyclone® V Avalon® Memory-Mapped (Avalon-MM) Interface for PCI Express* Solutions User Guide

Download PDF
ID 683494
Date 10/24/2024
Public
Document Table of Contents
Document Table of Contents x
1. Datasheet 2. Getting Started with the Avalon-MM Cyclone V Hard IP for PCI Express 3. Parameter Settings 4. Interfaces and Signal Descriptions 5. Registers 6. Reset and Clocks 7. Interrupts for Endpoints 8. Error Handling A. PCI Express Protocol Stack 9. Design Implementation 10. Additional Features 11. Transceiver PHY IP Reconfiguration 12. Debugging B. Frequently Asked Questions for PCI Express C. Lane Initialization and Reversal D. Document Revision History
1. Datasheet x
1.1. Avalon-MM Interface for PCIe Datasheet 1.2. Features 1.3. Release Information 1.4. Device Family Support 1.5. Configurations 1.6. Example Designs 1.7. IP Core Verification 1.8. Performance and Resource Utilization 1.9. Recommended Speed Grades 1.10. Creating a Design for PCI Express
1.7. IP Core Verification x
1.7.1. Compatibility Testing Environment
2. Getting Started with the Avalon-MM Cyclone V Hard IP for PCI Express x
2.1. Running Platform Designer 2.2. Generating the Example Design 2.3. Running a Gate-Level Simulation 2.4. Simulating the Single DWord Design 2.5. Understanding Channel Placement Guidelines 2.6. Generating Synthesis Files 2.7. Compiling the Design in the Quartus® Prime Software 2.8. Programming a Device
3. Parameter Settings x
3.1. Avalon-MM System Settings 3.2. Base Address Register (BAR) Settings 3.3. Device Identification Registers 3.4. Device Capabilities 3.5. Error Reporting 3.6. Link Capabilities 3.7. MSI and MSI-X Capabilities 3.8. Power Management 3.9. Avalon Memory‑Mapped System Settings
4. Interfaces and Signal Descriptions x
4.1. 64- or 128-Bit Avalon-MM Interface to the Endpoint Application Layer 4.2. Clock Signals 4.3. Reset Signals 4.4. Hard IP Status 4.5. Interrupts for Endpoints when Multiple MSI/MSI-X Support Is Enabled 4.6. Physical Layer Interface Signals
4.1. 64- or 128-Bit Avalon-MM Interface to the Endpoint Application Layer x
4.1.1. 32-Bit Non-Bursting Avalon-MM Control Register Access (CRA) Slave Signals 4.1.2. Bursting and Non-Bursting Avalon® -MM Module Signals 4.1.3. 64- or 128-Bit Bursting TX Avalon-MM Slave Signals
4.6. Physical Layer Interface Signals x
4.6.1. Transceiver Reconfiguration 4.6.2. Hard IP Status Extension 4.6.3. Serial Interface Signals 4.6.4. PIPE Interface Signals 4.6.5. Test Signals
4.6.2. Hard IP Status Extension x
4.6.2.1. Configuration Space Register Access 4.6.2.2. Configuration Space Register Access Timing
4.6.3. Serial Interface Signals x
4.6.3.1. Physical Layout of Hard IP in Cyclone V Devices 4.6.3.2. Channel Placement in Cyclone V Devices
5. Registers x
5.1. Correspondence between Configuration Space Registers and the PCIe Specification 5.2. Type 0 Configuration Space Registers 5.3. Type 1 Configuration Space Registers 5.4. PCI Express Capability Structures 5.5. Intel-Defined VSEC Registers 5.6. CvP Registers 5.7. 64- or 128-Bit Avalon-MM Bridge Register Descriptions 5.8. Programming Model for Avalon-MM Root Port 5.9. Uncorrectable Internal Error Mask Register 5.10. Uncorrectable Internal Error Status Register 5.11. Correctable Internal Error Mask Register 5.12. Correctable Internal Error Status Register
5.7. 64- or 128-Bit Avalon-MM Bridge Register Descriptions x
5.7.1. Avalon-MM to PCI Express Interrupt Registers
5.7.1. Avalon-MM to PCI Express Interrupt Registers x
5.7.1.1. Avalon-MM to PCI Express Interrupt Status Registers 5.7.1.2. Avalon-MM to PCI Express Interrupt Enable Registers 5.7.1.3. PCI Express Mailbox Registers 5.7.1.4. Avalon-MM-to-PCI Express Address Translation Table 5.7.1.5. PCI Express to Avalon-MM Interrupt Status and Enable Registers for Endpoints 5.7.1.6. Avalon-MM Mailbox Registers 5.7.1.7. Control Register Access (CRA) Avalon-MM Slave Port
5.8. Programming Model for Avalon-MM Root Port x
5.8.1. Sending a Write TLP 5.8.2. Sending a Read TLP or Receiving a Non-Posted Completion TLP 5.8.3. Examples of Reading and Writing BAR0 Using the CRA Interface 5.8.4. PCI Express to Avalon-MM Interrupt Status and Enable Registers for Root Ports 5.8.5. Root Port TLP Data Registers
6. Reset and Clocks x
6.1. Reset Sequence for Hard IP for PCI Express IP Core and Application Layer 6.2. Clocks
6.2. Clocks x
6.2.1. Clock Domains 6.2.2. Clock Summary
6.2.1. Clock Domains x
6.2.1.1. pclk 6.2.1.2. coreclkout_hip 6.2.1.3. pld_clk
7. Interrupts for Endpoints x
7.1. Enabling MSI or Legacy Interrupts 7.2. Generation of Avalon-MM Interrupts 7.3. Interrupts for Endpoints Using the Avalon-MM Interface with Multiple MSI/MSI-X Support
8. Error Handling x
8.1. Physical Layer Errors 8.2. Data Link Layer Errors 8.3. Transaction Layer Errors 8.4. Error Reporting and Data Poisoning 8.5. Uncorrectable and Correctable Error Status Bits
A. PCI Express Protocol Stack x
A.1. Top-Level Interfaces A.2. Data Link Layer A.3. Physical Layer A.4. 32-Bit PCI Express Avalon-MM Bridge A.5. Completer Only Single Dword Endpoint
A.1. Top-Level Interfaces x
A.1.1. Avalon-MM Interface A.1.2. Clocks and Reset A.1.3. Transceiver Reconfiguration A.1.4. Interrupts A.1.5. PIPE
A.4. 32-Bit PCI Express Avalon-MM Bridge x
A.4.1. Avalon‑MM Bridge TLPs A.4.2. Avalon-MM-to-PCI Express Write Requests A.4.3. Avalon-MM-to-PCI Express Upstream Read Requests A.4.4. PCI Express-to-Avalon-MM Read Completions A.4.5. PCI Express-to-Avalon-MM Downstream Write Requests A.4.6. PCI Express-to-Avalon-MM Downstream Read Requests A.4.7. Avalon-MM-to-PCI Express Read Completions A.4.8. PCI Express-to-Avalon-MM Address Translation for 32-Bit Bridge A.4.9. Minimizing BAR Sizes and the PCIe Address Space A.4.10. Avalon® -MM-to-PCI Express Address Translation Algorithm for 32-Bit Addressing
A.5. Completer Only Single Dword Endpoint x
A.5.1. RX Block A.5.2. Avalon-MM RX Master Block A.5.3. TX Block A.5.4. Interrupt Handler Block
9. Design Implementation x
9.1. Making Analog QSF Assignments Using the Assignment Editor 9.2. Making Pin Assignments 9.3. Recommended Reset Sequence to Avoid Link Training Issues
10. Additional Features x
10.1. Configuration over Protocol (CvP) 10.2. Autonomous Mode 10.3. ECRC
10.2. Autonomous Mode x
10.2.1. Enabling Autonomous Mode 10.2.2. Enabling CvP Initialization
10.3. ECRC x
10.3.1. ECRC on the RX Path 10.3.2. ECRC on the TX Path
11. Transceiver PHY IP Reconfiguration x
11.1. Connecting the Transceiver Reconfiguration Controller IP Core 11.2. Transceiver Reconfiguration Controller Connectivity for Designs Using CvP
12. Debugging x
12.1. Hardware Bring-Up Issues 12.2. Link Training 12.3. Use Third-Party PCIe Analyzer 12.4. BIOS Enumeration Issues
D. Document Revision History x
D.1. Arria® V and Cyclone® V Avalon® Memory Mapped (Avalon-MM) Interface for PCIe* Solutions User Guide Revision History
1. Datasheet
2. Getting Started with the Avalon-MM Cyclone V Hard IP for PCI Express
3. Parameter Settings
4. Interfaces and Signal Descriptions
5. Registers
6. Reset and Clocks
7. Interrupts for Endpoints
8. Error Handling
A. PCI Express Protocol Stack
9. Design Implementation
10. Additional Features
11. Transceiver PHY IP Reconfiguration
12. Debugging
B. Frequently Asked Questions for PCI Express
C. Lane Initialization and Reversal
D. Document Revision History

3.1. Avalon-MM System Settings

Table 9.  System Settings for PCI Express

Parameter

Value

Description

Number of Lanes

×1, ×2, ×4

Specifies the maximum number of lanes supported.

Lane Rate

Gen1 (2.5 Gbps)

Gen2 (2.5/5.0 Gbps)

Specifies the maximum data rate at which the link can operate.

Port type

Root Port

Native Endpoint

Specifies the port type. Altera recommends Native Endpoint for all new Endpoint designs. The Legacy Endpoint is not available for the Avalon‑MM Cyclone V Hard IP for PCI Express.

The Endpoint stores parameters in the Type 0 Configuration Space. The Root Port stores parameters in the Type 1 Configuration Space.

RX Buffer credit allocation -performance for received requests

Minimum

Low

Balanced

Determines the allocation of posted header credits, posted data credits, non-posted header credits, completion header credits, and completion data credits in the 16 KByte RX buffer. The settings allow you to adjust the credit allocation to optimize your system. The credit allocation for the selected setting displays in the message pane.

Refer to the Throughput Optimization chapter in the Cyclone V Avalon-ST Interface for PCIe Solutions User Guidefor more information about optimizing performance.

Refer to the Throughput Optimization chapter for more information about optimizing performance. The Flow Control chapter explains how the RX credit allocation and the Maximum payload RX Buffer credit allocation and the Maximum payload size that you choose affect the allocation of flow control credits. You can set the Maximum payload size parameter on the Device tab.

The Message window of the GUI dynamically updates the number of credits for Posted, Non‑Posted Headers and Data, and Completion Headers and Data as you change this selection.

  • Minimum RX Buffer credit allocation -performance for received requests )–This setting configures the minimum PCIe specification allowed for non-posted and posted request credits, leaving most of the RX Buffer space for received completion header and data. Select this option for variations where application logic generates many read requests and only infrequently receives single requests from the PCIe link.
  • Low–This setting configures a slightly larger amount of RX Buffer space for non-posted and posted request credits, but still dedicates most of the space for received completion header and data. Select this option for variations where application logic generates many read requests and infrequently receives small bursts of requests from the PCIe link. This option is recommended for typical endpoint applications where most of the PCIe traffic is generated by a DMA engine that is located in the endpoint application layer logic.
  • Balanced–This setting allocates approximately half the RX Buffer space to received requests and the other half of the RX Buffer space to received completions. Select this option for variations where the received requests and received completions are roughly equal.

Reference clock frequency

100 MHz

125 MHz

The PCI Express Base Specification requires a 100 MHz ±300 ppm reference clock. The 125 MHz reference clock is provided as a convenience for systems that include a 125 MHz clock source.

Use 62.5 MHz application clock

On/Off

This mode is only available only for Gen1 ×1.

Enable configuration via PCIe link

On/Off

When On, the Quartus® Prime software places the Endpoint in the location required for configuration via protocol (CvP). For more information about CvP, click the Configuration via Protocol (CvP) link below. CvP is not supported for Gen3 variants.

Related Information
Level Two Title