Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide

Download PDF
ID 683426
Date 4/09/2024
Public
Document Table of Contents
Document Table of Contents x
1. About LL Ethernet 10G MAC 2. Getting Started 3. LL Ethernet 10G MAC Intel® FPGA IP Design Examples 4. Functional Description 5. Configuration Registers 6. Interface Signals 7. Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide Archives 8. Document Revision History for the Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide
1. About LL Ethernet 10G MAC x
1.1. Features 1.2. Release Information 1.3. Low Latency Ethernet 10G MAC Operating Modes 1.4. Device Family Support 1.5. Performance and Resource Utilization
1.1. Features x
1.1.1. LL Ethernet 10G MAC and Legacy 10-Gbps Ethernet MAC
1.5. Performance and Resource Utilization x
1.5.1. Resource Utilization 1.5.2. TX and RX Latency
2. Getting Started x
2.1. Introduction to Intel® FPGA IP Cores 2.2. Installing and Licensing Intel® FPGA IP Cores 2.3. Specifying the IP Core Parameters and Options ( Quartus® Prime Pro Edition) 2.4. IP Core Generation Output ( Quartus® Prime Pro Edition) 2.5. Files Generated for Intel IP Cores (Legacy Parameter Editor) 2.6. Simulating Intel® FPGA IP Cores 2.7. Creating a Signal Tap Debug File to Match Your Design Hierarchy 2.8. Parameter Settings for the Low Latency Ethernet 10G MAC Intel® FPGA IP Core 2.9. Upgrading the Low Latency Ethernet 10G MAC Intel® FPGA IP Core 2.10. Design Considerations for the Low Latency Ethernet 10G MAC Intel® FPGA IP Core
2.10. Design Considerations for the Low Latency Ethernet 10G MAC Intel® FPGA IP Core x
2.10.1. Migrating from Legacy Ethernet 10G MAC to LL Ethernet 10G MAC 2.10.2. Timing Constraints 2.10.3. Jitter on PLL Clocks
2.10.1. Migrating from Legacy Ethernet 10G MAC to LL Ethernet 10G MAC x
2.10.1.1. Migration—32-bit Datapath on Avalon® Streaming Interface 2.10.1.2. Migration—Maintains 64-bit on Avalon® Streaming Interface
2.10.2. Timing Constraints x
2.10.2.1. Pseudo-Static CSR Fields 2.10.2.2. Clock Crosser 2.10.2.3. Dual Clock FIFO
3. LL Ethernet 10G MAC Intel® FPGA IP Design Examples x
3.1. LL Ethernet 10G MAC Intel® FPGA IP Design Example for Stratix® 10 Devices 3.2. LL Ethernet 10G MAC Intel® FPGA IP Design Example for Arria® 10 Devices 3.3. LL Ethernet 10G MAC Intel® FPGA IP Design Example for Cyclone® 10 GX Devices
4. Functional Description x
4.1. Architecture 4.2. Interfaces 4.3. Frame Types 4.4. TX Datapath 4.5. RX Datapath 4.6. Flow Control 4.7. Reset Requirements 4.8. Supported PHYs 4.9. XGMII Error Handling (Link Fault) 4.10. IEEE 1588v2
4.4. TX Datapath x
4.4.1. Padding Bytes Insertion 4.4.2. Address Insertion 4.4.3. CRC-32 Insertion 4.4.4. XGMII Encapsulation 4.4.5. Inter-Packet Gap Generation and Insertion 4.4.6. XGMII Transmission 4.4.7. Unidirectional Feature 4.4.8. TX Timing Diagrams
4.5. RX Datapath x
4.5.1. XGMII Decapsulation 4.5.2. CRC Checking 4.5.3. Address Checking 4.5.4. Frame Type Checking 4.5.5. Length Checking 4.5.6. CRC and Padding Bytes Removal 4.5.7. Overflow Handling 4.5.8. RX Timing Diagrams
4.5.5. Length Checking x
4.5.5.1. Frame Length 4.5.5.2. Payload Length
4.6. Flow Control x
4.6.1. IEEE 802.3 Flow Control 4.6.2. Priority-Based Flow Control
4.6.1. IEEE 802.3 Flow Control x
4.6.1.1. Pause Frame Reception 4.6.1.2. Pause Frame Transmission
4.6.2. Priority-Based Flow Control x
4.6.2.1. PFC Frame Reception 4.6.2.2. PFC Frame Transmission
4.8. Supported PHYs x
4.8.1. 10GBASE-R Register Mode
4.10. IEEE 1588v2 x
4.10.1. Architecture 4.10.2. TX Datapath 4.10.3. RX Datapath 4.10.4. Frame Format
4.10.4. Frame Format x
4.10.4.1. PTP Packet in IEEE 802.3 4.10.4.2. PTP Packet over UDP/IPv4 4.10.4.3. PTP Packet over UDP/IPv6
5. Configuration Registers x
5.1. Register Map 5.2. Register Access Definition 5.3. Primary MAC Address 5.4. MAC Reset Control Register 5.5. TX Configuration and Status Registers 5.6. Flow Control Registers 5.7. Unidirectional Control Registers 5.8. RX Configuration and Status Registers 5.9. Timestamp Registers 5.10. ECC Registers 5.11. Statistics Registers
5.1. Register Map x
5.1.1. Mapping 10-Gbps Ethernet MAC Registers to LL Ethernet 10G MAC Registers
5.9. Timestamp Registers x
5.9.1. Calculating Timing Adjustments
6. Interface Signals x
6.1. Clock and Reset Signals 6.2. Speed Selection Signal 6.3. Error Correction Signals 6.4. Unidirectional Signals 6.5. Avalon® Memory-Mapped Interface Programming Signals 6.6. Avalon® Streaming Data Interfaces 6.7. Avalon® Streaming Flow Control Signals 6.8. Avalon® Streaming Status Interface 6.9. PHY-side Interfaces 6.10. IEEE 1588v2 Interfaces
6.6. Avalon® Streaming Data Interfaces x
6.6.1. Avalon® Streaming TX Data Interface Signals 6.6.2. Avalon® Streaming RX Data Interface Signals 6.6.3. Avalon® Streaming Data Interface Clocks
6.8. Avalon® Streaming Status Interface x
6.8.1. Avalon® Streaming Interface TX Status Signals 6.8.2. Avalon® Streaming Interface RX Status Signals
6.9. PHY-side Interfaces x
6.9.1. XGMII TX Signals 6.9.2. XGMII RX Signals 6.9.3. GMII TX Signals 6.9.4. GMII RX Signals 6.9.5. MII TX Signals 6.9.6. MII RX Signals
6.10. IEEE 1588v2 Interfaces x
6.10.1. IEEE 1588v2 Egress TX Signals 6.10.2. IEEE 1588v2 Ingress RX Signals 6.10.3. IEEE 1588v2 Interface Clocks
1. About LL Ethernet 10G MAC
2. Getting Started
3. LL Ethernet 10G MAC Intel® FPGA IP Design Examples
4. Functional Description
5. Configuration Registers
6. Interface Signals
7. Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide Archives
8. Document Revision History for the Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide

4.6.2. Priority-Based Flow Control

Follow these steps to use the priority-based flow control (PFC):

  1. Turn on the Priority-based flow control (PFC) parameter and specify the number of priority levels using the Number of PFC priorities parameter. You can specify between 2 to 8 PFC priority levels.
  2. Set the following registers.
    • On the TX datapath:
      • Set tx_pauseframe_enable to 0 to disable the IEEE 802.3 flow control.
      • Set tx_pfc_priority_enable[n] to 1 to enable the PFC for priority queue n.
    • On the RX datapath:
      • Set the IGNORE_PAUSE bit in the rx_frame_control register to 1 to disable the IEEE 802.3 flow control.
      • Set the rx_pfc_control[7:0] register bits to 0 to enable the PFC. Most of the rest of the bits are unused.
  3. Connect the avalon_st_tx_pfc_gen_data signal to the corresponding RX client logic and the avalon_st_rx_pfc_pause_data signal to the corresponding TX client logic.
  4. You have the option to configure the MAC RX to forward the PFC frame to the client by setting the rx_pfc_control[16] register to 1. By default, the MAC RX drops the PFC frame after processing it.
You must handle the XON/XOFF requests in the following manner:
  1. Assert the XOFF, which runs at the clock frequency of 312.5 MHz, for at least 1 clock cycle, which runs at the clock frequency of 312.5 MHz to ensure that the PFC frame can transfer successfully.
  2. Assert the XON, which runs at the clock frequency of 312.5 MHz, for at least 25 clock cycle to ensure that the PFC frame can transfer successfully.

Section Content
PFC Frame Reception
PFC Frame Transmission

Level Two Title