Hard Processor System Component Reference Manual: Agilex™ 5 SoCs

Download PDF
ID 813752
Date 4/01/2024
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Introduction to the Agilex™ 5 Hard Processor System Component 2. Configuring the Agilex™ 5 Hard Processor System Component 3. Simulating the Agilex™ 5 HPS Component 4. Design Guidelines
1. Introduction to the Agilex™ 5 Hard Processor System Component x
1.1. Micro Processor Unit 1.2. Application Processor Subsystem 1.3. Peripheral Subsystem 1.4. CoreSight* Debug Components 1.5. Interconnect 1.6. FPGA Bridges 1.7. Introduction to the Agilex™ 5 Hard Processor System Component Revision History
2. Configuring the Agilex™ 5 Hard Processor System Component x
2.1. Parameterizing the HPS Component 2.2. HPS-FPGA Interfaces 2.3. SDRAM 2.4. HPS Clocks, Reset, Power 2.5. I/O Delays 2.6. Pin Mux and Peripherals 2.7. Generating and Compiling the HPS Component 2.8. Using the Address Span Extender Component 2.9. Configuring the Agilex™ 5 Hard Processor System Component Revision History
2.2. HPS-FPGA Interfaces x
2.2.1. General 2.2.2. HPS FPGA Bridges 2.2.3. DMA Controller Interface 2.2.4. Interrupts
2.2.1. General x
2.2.1.1. Enable MPU Standby and Event Signals 2.2.1.2. Enable General Purpose Signals 2.2.1.3. Enable Debug APB* Interface 2.2.1.4. Enable System Trace Macrocell (STM) Hardware Events 2.2.1.5. Enable SWJ-DP JTAG Interface 2.2.1.6. Enable FPGA Cross Trigger Interface 2.2.1.7. Enable AMBA* Trace Bus (ATB)
2.2.2. HPS FPGA Bridges x
2.2.2.1. FPGA to HPS Subordinate 2.2.2.2. FPGA to SDRAM Subordinate 2.2.2.3. HPS to FPGA Manager 2.2.2.4. Lightweight HPS to FPGA Manager
2.2.4. Interrupts x
2.2.4.1. FPGA-to-HPS 2.2.4.2. HPS-to-FPGA
2.3. SDRAM x
2.3.1. EMIF Interface
2.4. HPS Clocks, Reset, Power x
2.4.1. Input Clocks 2.4.2. PLL Clocks 2.4.3. Power and Resets
2.4.1. Input Clocks x
2.4.1.1. External Clocks 2.4.1.2. FPGA-to-HPS Clocks 2.4.1.3. Peripheral FPGA Clocks
2.4.2. PLL Clocks x
2.4.2.1. Main PLL Output 2.4.2.2. Peripheral PLL Output 2.4.2.3. MPU Clocks 2.4.2.4. NOC Clocks 2.4.2.5. Peripheral Clocks 2.4.2.6. HPS-to-FPGA User Clocks
2.4.3. Power and Resets x
2.4.3.1. Power Configurations 2.4.3.2. Reset Signals
2.6. Pin Mux and Peripherals x
2.6.1. Pin Mux GUI 2.6.2. EMAC PTP Interface 2.6.3. HPS I/O Open Drain 2.6.4. HPS I/O Locations
2.6.1. Pin Mux GUI x
2.6.1.1. Auto-Place IP 2.6.1.2. Advanced
2.6.1.1. Auto-Place IP x
2.6.1.1.1. Options for NAND, SDMMC, TRACE, TPIU, EMAC
2.6.1.1.1. Options for NAND, SDMMC, TRACE, TPIU, EMAC x
2.6.1.1.1.1. HPS IO Placement Priority
2.6.1.2. Advanced x
2.6.1.2.1. Advanced IP Placement 2.6.1.2.2. Advanced FPGA Placement
3. Simulating the Agilex™ 5 HPS Component x
3.1. Simulation Flows 3.2. Running the Simulation of the Design Examples 3.3. Clock and Reset Interface 3.4. FPGA-to-HPS AXI* Subordinate Interface 3.5. FPGA-to-SDRAM AXI* Subordinate Interface 3.6. HPS-to-FPGA AXI* Initiator Interface 3.7. Lightweight HPS-to-FPGA AXI* Initiator Interface 3.8. Simulating the Agilex™ 5 HPS Component Revision History
3.1. Simulation Flows x
3.1.1. Setting Up the HPS Component for Simulation 3.1.2. Generating the HPS Simulation Model in Platform Designer 3.1.3. RTL Simulation Setup Scripts
3.1.3. RTL Simulation Setup Scripts x
3.1.3.1. QuestaSim* Simulation Steps 3.1.3.2. Cadence® Xcelium* Simulation Steps 3.1.3.3. Synopsys* VCS* Simulation Steps 3.1.3.4. Synopsys* VCS* MX Simulation Steps 3.1.3.5. Aldec® Riviera-PRO* Simulation Steps
3.2. Running the Simulation of the Design Examples x
3.2.1. HPS-to-FPGA Bridge (H2F) 3.2.2. Lightweight HPS-to-FPGA (LWH2F) 3.2.3. FPGA-to-HPS Bridge (F2H) 3.2.4. FPGA-to-SDRAM Bridge (F2SDRAM)
3.2.1. HPS-to-FPGA Bridge (H2F) x
3.2.1.1. Steps to run the Simulation in Questa* Intel® FPGA Edition 3.2.1.2. Steps to run the Simulation in Synopsys* VCS*
3.2.2. Lightweight HPS-to-FPGA (LWH2F) x
3.2.2.1. Steps to run the Simulation in Questa* Intel® FPGA Edition 3.2.2.2. Steps to run the Simulation in Synopsys* VCS*
3.2.3. FPGA-to-HPS Bridge (F2H) x
3.2.3.1. Steps to run the Simulation in Questa* Intel® FPGA Edition 3.2.3.2. Steps to run the Simulation in Synopsys* VCS*
3.2.4. FPGA-to-SDRAM Bridge (F2SDRAM) x
3.2.4.1. Steps to run the Simulation in Questa* Intel® FPGA Edition 3.2.4.2. Steps to run the Simulation in Synopsys* VCS*
3.3. Clock and Reset Interface x
3.3.1. Clock Interface 3.3.2. Reset Interface
4. Design Guidelines x
4.1. HPS System Reset Considerations 4.2. Design Guidelines Revision History
1. Introduction to the Agilex™ 5 Hard Processor System Component
2. Configuring the Agilex™ 5 Hard Processor System Component
3. Simulating the Agilex™ 5 HPS Component
4. Design Guidelines

2.2.1.1. Enable MPU Standby and Event Signals

Microprocessor Unit (MPU) standby signals are notification signals to the FPGA fabric that the MPU is in standby. Event signals wake up the Arm* Cortex*-A55/ Arm* Cortex*-A76 processors from a wait-for-event (WFE) state. Turning on the Enable MPU standby & event signals option enables the h2f_mpu_events conduit, which is comprised of the following signals:

Table 1.   h2f_mpu_events Signals
Signal Name Interface Type Interface Description
h2f_mpu_events_eventi_ack

Conduit

MPU event input request acknowledge. It is not asserted until EVENTI_REQ is high, and then remains asserted until after EVENTI_REQ goes low.

h2f_mpu_events_evento_ack

Conduit

MPU event output request acknowledge. It must not be asserted until EVENTO_REQ is high, and then must remain asserted until after EVENTO_REQ goes low.

h2f_mpu_events_eventi_req

Conduit

The EVENTI_REQ input indicates that another cluster or system component has signaled a WFE wake up event.

h2f_mpu_events_evento_req

Conduit

A Send Event (SEV) instruction signals a WFE wake up event to other clusters by asserting the EVENTO_REQ output.

Figure 5.  Platform Designer General Tab with Enable MPU Standby and Event Interfaces Selected
Level Two Title