PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide

Download PDF
ID 683716
Date 12/13/2021
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the PHY Lite for Parallel Interfaces IP 2. PHY Lite for Parallel Interfaces Intel Agilex FPGA IP 3. PHY Lite for Parallel Interfaces Intel Stratix 10 FPGA IP 4. PHY Lite for Parallel Interfaces Intel Arria 10 and Intel Cyclone 10 GX FPGA IPs 5. PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide Document Archives 6. Document Revision History for the PHY Lite for Parallel Interfaces IP User Guide
1. About the PHY Lite for Parallel Interfaces IP x
1.1. Device Family Support 1.2. Features
2. PHY Lite for Parallel Interfaces Intel Agilex FPGA IP x
2.1. Release Information 2.2. Functional Description 2.3. Getting Started 2.4. I/O Standards 2.5. Design Guidelines 2.6. Design Example
2.2. Functional Description x
2.2.1. Intel® Agilex™ I/O Sub-bank Interconnects 2.2.2. Intel® Agilex™ Input DQS/Strobe Tree 2.2.3. PHY Lite for Parallel Interfaces Intel® Agilex™ FPGA IP Top Level Interfaces 2.2.4. Dynamic Reconfiguration 2.2.5. I/O Timing
2.2.3. PHY Lite for Parallel Interfaces Intel® Agilex™ FPGA IP Top Level Interfaces x
2.2.3.1. Clocks 2.2.3.2. Output Path 2.2.3.3. Input Path
2.2.3.1. Clocks x
2.2.3.1.1. Clock Frequency Relationships
2.2.3.2. Output Path x
2.2.3.2.1. Output Path Data Alignment
2.2.3.3. Input Path x
2.2.3.3.1. Input Path Data Alignment
2.2.4. Dynamic Reconfiguration x
2.2.4.1. Connectivity 2.2.4.2. Reconfiguration Features and Register Addressing 2.2.4.3. Dynamic Reconfiguration Guidelines
2.2.4.2. Reconfiguration Features and Register Addressing x
2.2.4.2.1. Control Registers Addresses 2.2.4.2.2. Control Registers
2.2.4.3. Dynamic Reconfiguration Guidelines x
2.2.4.3.1. Strobe Enable Window Calibration 2.2.4.3.2. Output and Strobe Enable Minimum and Maximum Phase Settings 2.2.4.3.3. Input DQ/DQS Delay Chains Maximum Values
2.3. Getting Started x
2.3.1. Parameter Settings 2.3.2. Signals
2.3.1. Parameter Settings x
2.3.1.1. Read Latency 2.3.1.2. Write Latency
2.3.2. Signals x
2.3.2.1. Clock and Reset Interface Signals 2.3.2.2. Output Path Signals 2.3.2.3. Input Path Signals
2.4. I/O Standards x
2.4.1. Input Buffer Reference Voltage (VREF) 2.4.2. On-Chip Termination (OCT)
2.4.2. On-Chip Termination (OCT) x
2.4.2.1. RZQ_GROUP Assignment
2.5. Design Guidelines x
2.5.1. Guidelines: Group Pin Placement 2.5.2. Reference Clock 2.5.3. Reset
2.6. Design Example x
2.6.1. Generate the Design Example
2.6.1. Generate the Design Example x
2.6.1.1. Design Example without Dynamic Reconfiguration 2.6.1.2. Dynamic Reconfiguration Design Examples
2.6.1.1. Design Example without Dynamic Reconfiguration x
2.6.1.1.1. Generate the Synthesis Design Example 2.6.1.1.2. Generate the Simulation Design Example
2.6.1.2. Dynamic Reconfiguration Design Examples x
2.6.1.2.1. Generate the Synthesis Design Example 2.6.1.2.2. Generate the Simulation Design Example
3. PHY Lite for Parallel Interfaces Intel Stratix 10 FPGA IP x
3.1. Release Information 3.2. Functional Description 3.3. Getting Started 3.4. I/O Standards 3.5. Design Guidelines 3.6. Design Example
3.2. Functional Description x
3.2.1. Top Level Interfaces 3.2.2. Clocks 3.2.3. Output Path 3.2.4. Input Path 3.2.5. Dynamic Reconfiguration
3.2.2. Clocks x
3.2.2.1. Clock Frequency Relationships
3.2.3. Output Path x
3.2.3.1. Output Path Data Alignment
3.2.4. Input Path x
3.2.4.1. Input Path Data Alignment
3.2.5. Dynamic Reconfiguration x
3.2.5.1. RTL Connectivity 3.2.5.2. Address Lookup 3.2.5.3. Reconfiguration Features and Register Addressing 3.2.5.4. Calibration Guidelines
3.2.5.1. RTL Connectivity x
3.2.5.1.1. Daisy Chain
3.2.5.2. Address Lookup x
3.2.5.2.1. Strobes 3.2.5.2.2. Parameter Table Examples
3.2.5.3. Reconfiguration Features and Register Addressing x
3.2.5.3.1. PHY Lite for Parallel Interfaces Intel Stratix 10 FPGA IP Control Registers Addresses 3.2.5.3.2. Control Registers Description
3.2.5.4. Calibration Guidelines x
3.2.5.4.1. Strobe Enable Window Calibration 3.2.5.4.2. Output and Strobe Enable Minimum and Maximum Phase Settings
3.3. Getting Started x
3.3.1. Parameter Settings 3.3.2. Signals
3.3.1. Parameter Settings x
3.3.1.1. Read Latency 3.3.1.2. Write Latency
3.3.2. Signals x
3.3.2.1. Clock and Reset Interface Signals 3.3.2.2. Output Path Signals 3.3.2.3. Input Path Signals 3.3.2.4. Avalon Configuration Bus Interface Signals 3.3.2.5. Termination Signals
3.4. I/O Standards x
3.4.1. Input Buffer Reference Voltage (VREF) 3.4.2. On-Chip Termination (OCT)
3.4.1. Input Buffer Reference Voltage (VREF) x
3.4.1.1. Calibrated VREF Settings
3.4.2. On-Chip Termination (OCT) x
3.4.2.1. RZQ_GROUP Assignment 3.4.2.2. Manual Insertion of OCT Block
3.5. Design Guidelines x
3.5.1. Guidelines: Group Pin Placement 3.5.2. Reference Clock 3.5.3. Reset 3.5.4. Constraining Multiple PHY Lite for Parallel Interfaces to One I/O Bank 3.5.5. Dynamic Reconfiguration 3.5.6. Timing
3.5.6. Timing x
3.5.6.1. Timing Components 3.5.6.2. Timing Constraints and Files 3.5.6.3. Timing Analysis 3.5.6.4. Timing Closure Guidelines
3.5.6.2. Timing Constraints and Files x
3.5.6.2.1. <variation_name>.sdc 3.5.6.2.2. <variation_name>_parameter.tcl 3.5.6.2.3. <variation_name>_ip_parameters.tcl 3.5.6.2.4. <variation_name>_pin_map.tcl 3.5.6.2.5. <variation_name>_report_timing.tcl 3.5.6.2.6. <variation_name>_report_timing_core.tcl
3.5.6.4. Timing Closure Guidelines x
3.5.6.4.1. Timing Closure: Dynamic Reconfiguration 3.5.6.4.2. Timing Closure: Input Strobe Setup and Hold Delay Constraints 3.5.6.4.3. Timing Closure: Output Strobe Setup and Hold Delay Constraints 3.5.6.4.4. Timing Closure: Non Edge-Aligned Input Data 3.5.6.4.5. I/O Timing Violation 3.5.6.4.6. Internal FPGA Path Timing Violation
3.6. Design Example x
3.6.1. Generate the Design Example
3.6.1. Generate the Design Example x
3.6.1.1. Design Example without Dynamic Reconfiguration 3.6.1.2. Dynamic Reconfiguration Design Examples
3.6.1.1. Design Example without Dynamic Reconfiguration x
3.6.1.1.1. Generate the Hardware Design Example 3.6.1.1.2. Generate the Simulation Design Example
3.6.1.2. Dynamic Reconfiguration Design Examples x
3.6.1.2.1. Dynamic Reconfiguration Using Finite State Machine
4. PHY Lite for Parallel Interfaces Intel Arria 10 and Intel Cyclone 10 GX FPGA IPs x
4.1. Release Information 4.2. Functional Description 4.3. Getting Started 4.4. I/O Standards 4.5. Design Guidelines 4.6. Design Example 4.7. Application Specific Design Example
4.2. Functional Description x
4.2.1. Top Level Interfaces 4.2.2. Clocks 4.2.3. Output Path 4.2.4. Input Path 4.2.5. Dynamic Reconfiguration
4.2.2. Clocks x
4.2.2.1. Clock Frequency Relationships
4.2.3. Output Path x
4.2.3.1. Output Path Data Alignment
4.2.4. Input Path x
4.2.4.1. Input Path Data Alignment
4.2.5. Dynamic Reconfiguration x
4.2.5.1. RTL Connectivity 4.2.5.2. Address Lookup 4.2.5.3. Reconfiguration Features and Register Addressing 4.2.5.4. Calibration Guidelines
4.2.5.1. RTL Connectivity x
4.2.5.1.1. Daisy Chain
4.2.5.2. Address Lookup x
4.2.5.2.1. Strobes 4.2.5.2.2. Parameter Table Examples
4.2.5.3. Reconfiguration Features and Register Addressing x
4.2.5.3.1. PHY Lite for Parallel Interfaces Intel Arria 10 FPGA IP and PHY Lite for Parallel Interfaces Intel Cyclone 10 GX IPs Address Registers 4.2.5.3.2. Control Registers Description
4.2.5.4. Calibration Guidelines x
4.2.5.4.1. Strobe Enable Window Calibration 4.2.5.4.2. Output and Strobe Enable Minimum and Maximum Phase Settings
4.3. Getting Started x
4.3.1. Parameter Settings 4.3.2. Signals
4.3.1. Parameter Settings x
4.3.1.1. Read Latency 4.3.1.2. Write Latency
4.3.2. Signals x
4.3.2.1. Clock and Reset Interface Signals 4.3.2.2. Output Path Signals 4.3.2.3. Input Path Signals 4.3.2.4. Avalon Configuration Bus Interface Signals 4.3.2.5. Termination Signals
4.4. I/O Standards x
4.4.1. Input Buffer Reference Voltage (VREF) 4.4.2. On-Chip Termination (OCT)
4.4.1. Input Buffer Reference Voltage (VREF) x
4.4.1.1. Calibrated VREF Settings
4.4.2. On-Chip Termination (OCT) x
4.4.2.1. RZQ_GROUP Assignment 4.4.2.2. Manual Insertion of OCT Block
4.5. Design Guidelines x
4.5.1. Guidelines: Group Pin Placement 4.5.2. Reference Clock 4.5.3. Reset 4.5.4. Constraining Multiple PHY Lite for Parallel Interfaces to One I/O Bank 4.5.5. Dynamic Reconfiguration 4.5.6. Timing
4.5.6. Timing x
4.5.6.1. Timing Components 4.5.6.2. Timing Constraints and Files 4.5.6.3. Timing Analysis 4.5.6.4. Timing Closure Guidelines
4.5.6.2. Timing Constraints and Files x
4.5.6.2.1. <variation_name>.sdc 4.5.6.2.2. <variation_name>_parameter.tcl 4.5.6.2.3. <variation_name>_ip_parameters.tcl 4.5.6.2.4. <variation_name>_pin_map.tcl 4.5.6.2.5. <variation_name>_report_timing.tcl 4.5.6.2.6. <variation_name>_report_timing_core.tcl
4.5.6.4. Timing Closure Guidelines x
4.5.6.4.1. Timing Closure: Dynamic Reconfiguration 4.5.6.4.2. Timing Closure: Input Strobe Setup and Hold Delay Constraints 4.5.6.4.3. Timing Closure: Output Strobe Setup and Hold Delay Constraints 4.5.6.4.4. Timing Closure: Non Edge-Aligned Input Data 4.5.6.4.5. I/O Timing Violation 4.5.6.4.6. Internal FPGA Path Timing Violation
4.6. Design Example x
4.6.1. Generate the Design Example
4.6.1. Generate the Design Example x
4.6.1.1. Design Example without Dynamic Reconfiguration 4.6.1.2. Dynamic Reconfiguration Design Examples
4.6.1.1. Design Example without Dynamic Reconfiguration x
4.6.1.1.1. Generate the Hardware Design Example 4.6.1.1.2. Generate the Simulation Design Example
4.6.1.2. Dynamic Reconfiguration Design Examples x
4.6.1.2.1. Dynamic Reconfiguration with Debug Kit 4.6.1.2.2. Dynamic Reconfiguration Using Finite State Machine
4.7. Application Specific Design Example x
4.7.1. Implementation using the PHY Lite for Parallel Interfaces IP
1. About the PHY Lite for Parallel Interfaces IP
2. PHY Lite for Parallel Interfaces Intel Agilex FPGA IP
3. PHY Lite for Parallel Interfaces Intel Stratix 10 FPGA IP
4. PHY Lite for Parallel Interfaces Intel Arria 10 and Intel Cyclone 10 GX FPGA IPs
5. PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide Document Archives
6. Document Revision History for the PHY Lite for Parallel Interfaces IP User Guide

4.2.2. Clocks

The PHY Lite for Parallel Interfaces IP uses a reference clock that is sourced from a dedicated clock pin to the PLL inside the IP. This PLL provides four clock domains for the output and input paths.

Table 58.   PHY Lite for Parallel Interfaces IP Clock Domains
Clock Domain Description
Core clock This clock is generated internally by the IP and it is used for all transfers between the FPGA core fabric and I/O banks. The clock phase alignment circuitry ensures that this clock is kept in phase with the PHY clock for core-to-periphery and periphery-to-core transfers.
PHY clock This clock is used internally by the IP for PHY circuitry running at the same frequency as the core clock.
VCO clock This clock is generated internally by the PLL. It is used by both the input and output paths to generate PVT compensated delays in the interpolator.
Interface clock This is the clock frequency of the external device connected to the FPGA I/Os.
Table 59.   PHY Lite for Parallel Interfaces Intel® Arria® 10 FPGA IP Supported Interface Frequency Use the Timing Analyzer to perform timing closure to ensure your design fulfilled all timing constraints with the supported frequencies indicated in the table. Full, half, and quarter core clock rate refers to the ratio of the core clock and interface clock. For example, an interface clock frequency of 800 MHz has full core clock rate of 800 MHz, half core clock rate of 400 MHz, and quarter core clock rate of 200 MHz.
Core Clock Rate Speed Grade –1 (MHz) Speed Grade –2 (MHz) Speed Grade –3 (MHz)
Min Max Min Max Min Max
Full 100 333 100 266 100 233
Half 100 667 100 533 100 466
Quarter 100 1200 100 1067 100 933
Table 60.   PHY Lite for Parallel Interfaces Intel® Cyclone® 10 GX FPGA IP Supported Interface Frequency Use the Timing Analyzer to perform timing closure to ensure your design fulfilled all timing constraints with the supported frequencies indicated in the table. Full, half, and quarter core clock rate refers to the ratio of the core clock and interface clock. For example, an interface clock frequency of 800 MHz has full core clock rate of 800 MHz, half core clock rate of 400 MHz, and quarter core clock rate of 200 MHz.
Core Clock Rate Speed Grade –5 (MHz) Speed Grade –6 (MHz)
Min Max Min Max
Full 100 266 100 233
Half 100 533 100 466
Quarter 100 1067 100 933
Related Information
Level Two Title