L-tile and H-tile Avalon® Memory-mapped Intel® FPGA IP for PCI Express* User Guide

Download PDF
ID 683667
Date 9/26/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Introduction 2. Quick Start Guide 3. Interface Overview 4. Parameters 5. Designing with the IP Core 6. Block Descriptions 7. Registers 8. Programming Model for the DMA Descriptor Controller 9. Programming Model for the Avalon® -MM Root Port 10. Avalon-MM Testbench and Design Example 11. Troubleshooting and Observing the Link A. PCI Express Core Architecture B. Root Port Enumeration C. Document Revision History
1. Introduction x
1.1. Avalon-MM Interface for PCIe 1.2. Features 1.3. Release Information 1.4. Device Family Support 1.5. Recommended Fabric Speed Grades 1.6. Performance and Resource Utilization 1.7. Transceiver Tiles 1.8. PCI Express IP Core Package Layout 1.9. Channel Availability
2. Quick Start Guide x
2.1. Design Components 2.2. Hardware and Software Requirements 2.3. Directory Structure 2.4. Generating the Design Example 2.5. Simulating the Design Example 2.6. Compiling the Design Example and Programming the Device 2.7. Installing the Linux Kernel Driver 2.8. Running the Design Example Application
3. Interface Overview x
3.1. Avalon-MM DMA Interfaces when Descriptor Controller Is Internally Instantiated 3.2. Avalon-MM DMA Interfaces when Descriptor Controller is Externally Instantiated 3.3. Other Avalon-MM Interfaces 3.4. Clocks and Reset 3.5. System Interfaces
3.3. Other Avalon-MM Interfaces x
3.3.1. Avalon-MM Master Interfaces 3.3.2. Avalon-MM Slave Interfaces 3.3.3. Control Register Access (CRA) Avalon-MM Slave
4. Parameters x
4.1. Avalon-MM Settings 4.2. Base Address Registers 4.3. Device Identification Registers 4.4. PCI Express and PCI Capabilities Parameters 4.5. Configuration, Debug and Extension Options 4.6. PHY Characteristics 4.7. Example Designs
4.4. PCI Express and PCI Capabilities Parameters x
4.4.1. Device Capabilities 4.4.2. Link Capabilities 4.4.3. MSI and MSI-X Capabilities 4.4.4. Slot Capabilities 4.4.5. Power Management 4.4.6. Vendor Specific Extended Capability (VSEC)
5. Designing with the IP Core x
5.1. Generation 5.2. Simulation 5.3. IP Core Generation Output ( Intel® Quartus® Prime Pro Edition) 5.4. Channel Layout and PLL Usage
6. Block Descriptions x
6.1. Interfaces
6.1. Interfaces x
6.1.1. Intel® Stratix® 10 DMA Avalon-MM DMA Interface to the Application Layer 6.1.2. Avalon-MM Interface to the Application Layer 6.1.3. Clocks and Reset 6.1.4. Interrupts 6.1.5. Flush Requests 6.1.6. Serial Data, PIPE, Status, Reconfiguration, and Test Interfaces
6.1.1. Intel® Stratix® 10 DMA Avalon-MM DMA Interface to the Application Layer x
6.1.1.1. Descriptor Controller Interfaces when Instantiated Internally 6.1.1.2. Write DMA Avalon-MM Master Port 6.1.1.3. Descriptor Controller Interfaces when Instantiated Externally
6.1.1.1. Descriptor Controller Interfaces when Instantiated Internally x
6.1.1.1.1. Read Data Mover 6.1.1.1.2. Read Descriptor Controller Avalon-MM Master interface 6.1.1.1.3. Write Descriptor Controller Avalon-MM Master Interface 6.1.1.1.4. Read Descriptor Table Avalon-MM Slave Interface 6.1.1.1.5. Write Descriptor Table Avalon-MM Slave Interface
6.1.1.3. Descriptor Controller Interfaces when Instantiated Externally x
6.1.1.3.1. Avalon® -ST Descriptor Source
6.1.2. Avalon-MM Interface to the Application Layer x
6.1.2.1. Bursting and Non-Bursting Avalon® -MM Module Signals 6.1.2.2. Non-Bursing Slave Module 6.1.2.3. 32-Bit Control Register Access (CRA) Slave Signals 6.1.2.4. Bursting Slave Module
6.1.3. Clocks and Reset x
6.1.3.1. Clocks 6.1.3.2. Resets
6.1.4. Interrupts x
6.1.4.1. MSI Interrupts for Endpoints 6.1.4.2. Legacy Interrupts
6.1.6. Serial Data, PIPE, Status, Reconfiguration, and Test Interfaces x
6.1.6.1. Serial Data Interface 6.1.6.2. PIPE Interface 6.1.6.3. Hard IP Status Interface 6.1.6.4. Hard IP Reconfiguration 6.1.6.5. Test Interface
7. Registers x
7.1. Configuration Space Registers 7.2. Avalon-MM DMA Bridge Registers
7.1. Configuration Space Registers x
7.1.1. Register Access Definitions 7.1.2. PCI Configuration Header Registers 7.1.3. PCI Express Capability Structures 7.1.4. Intel Defined VSEC Capability Header 7.1.5. Uncorrectable Internal Error Status Register 7.1.6. Uncorrectable Internal Error Mask Register 7.1.7. Correctable Internal Error Status Register 7.1.8. Correctable Internal Error Mask Register
7.1.4. Intel Defined VSEC Capability Header x
7.1.4.1. Intel Defined Vendor Specific Header 7.1.4.2. Intel Marker 7.1.4.3. JTAG Silicon ID 7.1.4.4. User Configurable Device and Board ID
7.2. Avalon-MM DMA Bridge Registers x
7.2.1. PCI Express Avalon-MM Bridge Register Address Map 7.2.2. DMA Descriptor Controller Registers
7.2.1. PCI Express Avalon-MM Bridge Register Address Map x
7.2.1.1. Avalon-MM to PCI Express Interrupt Status Registers 7.2.1.2. Avalon-MM to PCI Express Interrupt Enable Registers 7.2.1.3. Address Mapping for High-Performance Avalon-MM 32-Bit Slave Modules 7.2.1.4. PCI Express to Avalon-MM Interrupt Status and Enable Registers for Endpoints 7.2.1.5. PCI Express Configuration Information Registers
7.2.2. DMA Descriptor Controller Registers x
7.2.2.1. Read DMA Internal Descriptor Controller Registers 7.2.2.2. Write DMA Internal Descriptor Controller Registers
8. Programming Model for the DMA Descriptor Controller x
8.1. Read DMA Example 8.2. Write DMA Example 8.3. Software Program for Simultaneous Read and Write DMA 8.4. Read DMA and Write DMA Descriptor Format
9. Programming Model for the Avalon® -MM Root Port x
9.1. Root Port TLP Data Control and Status Registers 9.2. Sending a TLP 9.3. Receiving a Non-Posted Completion TLP 9.4. Example of Reading and Writing BAR0 Using the CRA Interface
10. Avalon-MM Testbench and Design Example x
10.1. Avalon-MM Endpoint Testbench 10.2. Endpoint Design Example 10.3. Avalon® -MM Test Driver Module 10.4. Root Port BFM 10.5. BFM Procedures and Functions
10.2. Endpoint Design Example x
10.2.1. BAR Setup
10.4. Root Port BFM x
10.4.1. Overview 10.4.2. Issuing Read and Write Transactions to the Application Layer 10.4.3. Configuration of Root Port and Endpoint 10.4.4. Configuration Space Bus and Device Numbering 10.4.5. BFM Memory Map
10.5. BFM Procedures and Functions x
10.5.1. ebfm_barwr Procedure 10.5.2. ebfm_barwr_imm Procedure 10.5.3. ebfm_barrd_wait Procedure 10.5.4. ebfm_barrd_nowt Procedure 10.5.5. ebfm_cfgwr_imm_wait Procedure 10.5.6. ebfm_cfgwr_imm_nowt Procedure 10.5.7. ebfm_cfgrd_wait Procedure 10.5.8. ebfm_cfgrd_nowt Procedure 10.5.9. BFM Configuration Procedures 10.5.10. BFM Shared Memory Access Procedures 10.5.11. BFM Log and Message Procedures 10.5.12. Verilog HDL Formatting Functions
10.5.9. BFM Configuration Procedures x
10.5.9.1. ebfm_cfg_rp_ep Procedure 10.5.9.2. ebfm_cfg_decode_bar Procedure
10.5.10. BFM Shared Memory Access Procedures x
10.5.10.1. Shared Memory Constants 10.5.10.2. shmem_write Task 10.5.10.3. shmem_read Function 10.5.10.4. shmem_display Verilog HDL Function 10.5.10.5. shmem_fill Procedure 10.5.10.6. shmem_chk_ok Function
10.5.11. BFM Log and Message Procedures x
10.5.11.1. ebfm_display Verilog HDL Function 10.5.11.2. ebfm_log_stop_sim Verilog HDL Function 10.5.11.3. ebfm_log_set_suppressed_msg_mask Task 10.5.11.4. ebfm_log_set_stop_on_msg_mask Verilog HDL Task 10.5.11.5. ebfm_log_open Verilog HDL Function 10.5.11.6. ebfm_log_close Verilog HDL Function
10.5.12. Verilog HDL Formatting Functions x
10.5.12.1. himage1 10.5.12.2. himage2 10.5.12.3. himage4 10.5.12.4. himage8 10.5.12.5. himage16 10.5.12.6. dimage1 10.5.12.7. dimage2 10.5.12.8. dimage3 10.5.12.9. dimage4 10.5.12.10. dimage5 10.5.12.11. dimage6 10.5.12.12. dimage7
11. Troubleshooting and Observing the Link x
11.1. Troubleshooting 11.2. PCIe Link Inspector Overview
11.1. Troubleshooting x
11.1.1. Simulation Fails To Progress Beyond Polling.Active State 11.1.2. Hardware Bring-Up Issues 11.1.3. Link Training 11.1.4. Use Third-Party PCIe Analyzer
11.2. PCIe Link Inspector Overview x
11.2.1. PCIe* Link Inspector Hardware
11.2.1. PCIe* Link Inspector Hardware x
11.2.1.1. Enabling the PCIe* Link Inspector 11.2.1.2. Launching the PCIe* Link Inspector 11.2.1.3. The PCIe* Link Inspector LTSSM Monitor 11.2.1.4. Accessing the Configuration Space and Transceiver Registers 11.2.1.5. Additional Status Commands
11.2.1.3. The PCIe* Link Inspector LTSSM Monitor x
11.2.1.3.1. LTSSM Monitor Registers 11.2.1.3.2. ltssm_save2file <file_name> 11.2.1.3.3. ltssm_file2console 11.2.1.3.4. ltssm_debug_check 11.2.1.3.5. ltssm_display <num_states> 11.2.1.3.6. ltssm_save_oldstates
11.2.1.4. Accessing the Configuration Space and Transceiver Registers x
11.2.1.4.1. PCIe* Link Inspector Commands 11.2.1.4.2. NPDME PLL and Channel Commands 11.2.1.4.3. Register Address Map
11.2.1.5. Additional Status Commands x
11.2.1.5.1. Displaying PLL Lock and Calibration Status Registers
A. PCI Express Core Architecture x
A.1. Transaction Layer A.2. Data Link Layer A.3. Physical Layer
C. Document Revision History x
C.1. Document Revision History for the L-tile and H-tile Avalon® Memory-mapped Intel® FPGA IP for PCI Express* User Guide
1. Introduction
2. Quick Start Guide
3. Interface Overview
4. Parameters
5. Designing with the IP Core
6. Block Descriptions
7. Registers
8. Programming Model for the DMA Descriptor Controller
9. Programming Model for the Avalon® -MM Root Port
10. Avalon-MM Testbench and Design Example
11. Troubleshooting and Observing the Link
A. PCI Express Core Architecture
B. Root Port Enumeration
C. Document Revision History

4. Parameters

This chapter provides a reference for all the parameters of the Intel L-/H-Tile Avalon-ST for PCI Express IP core.
Table 13.  Design Environment ParameterStarting in Intel® Quartus® Prime 18.0, there is a new parameter Design Environment in the parameters editor window.

Parameter

Value

Description

Design Environment

Standalone

System

Identifies the environment that the IP is in.

  • The Standalone environment refers to the IP being in a standalone state where all its interfaces are exported.
  • The System environment refers to the IP being instantiated in a Platform Designer system.
Table 14.  System Settings

Parameter

Value

Description

Application Interface Type

Avalon-MM

Selects the interface to the Application Layer.

Application Interface Width

256-bit

Selects the width of the interface to the Application Layer. Currently, the only option available for this interface width is 256-bit .
Note: DMA operations are only supported when this parameter is set to 256-bit.
Hard IP Mode

Gen3x8, 256-bit interface, 250 MHz

Gen3x4, 256-bit interface, 125 MHz

Gen3x2, 256-bit interface, 125 MHz

Gen3x1, 256-bit interface, 125 MHz

Gen2x16, 256-bit interface, 250 MHz

Gen2x8, 256-bit interface, 125 MHz

Gen2x4, 256-bit interface, 125 MHz

Gen2x2, 256-bit interface, 125 MHz

Gen2x1, 256-bit interface, 125 MHz

Gen1x16, 256-bit interface, 125 MHz

Gen1x8, 256-bit interface, 125 MHz

Gen1x4, 256-bit interface, 125 MHz

Gen1x2, 256-bit interface, 125 MHz

Gen1x1, 256-bit interface, 125 MHz

Selects the following elements:

  • The lane data rate. Gen1, Gen2, and Gen3 are supported
  • The Application Layer interface frequency

The width of the data interface between the hard IP Transaction Layer and the Application Layer implemented in the FPGA fabric.

Note: If the Mode selected is not available for the configuration chosen, an error message displays in the Message pane.
Port type

Native Endpoint

Root Port

Specifies the port type.

The Endpoint stores parameters in the Type 0 Configuration Space. The Root Port stores parameters in the Type 1 Configuration Space.

A Root Port testbench is not available in the current release. If you select the Root Port, you have to create your own testbench.


Section Content
Avalon-MM Settings
Base Address Registers
Device Identification Registers
PCI Express and PCI Capabilities Parameters
Configuration, Debug and Extension Options
PHY Characteristics
Example Designs

Level Two Title