Serial Lite IV Intel® FPGA IP User Guide

Download PDF
ID 683655
Date 10/02/2023
Public
Document Table of Contents
Document Table of Contents x
1. About the Serial Lite IV Intel® FPGA IP User Guide 2. Serial Lite IV Intel® FPGA IP Overview 3. Functional Description 4. Getting Started 5. Parameters 6. Serial Lite IV Intel® FPGA IP Interface Signals 7. Designing with Serial Lite IV Intel® FPGA IP 8. Serial Lite IV Intel® FPGA IP Registers 9. Serial Lite IV Intel® FPGA IP User Guide Archives 10. Document Revision History for the Serial Lite IV Intel® FPGA IP User Guide
2. Serial Lite IV Intel® FPGA IP Overview x
2.1. Release Information 2.2. Supported Features 2.3. IP Version Support Level 2.4. Device Speed Grade Support 2.5. Resource Utilization and Latency 2.6. Bandwidth Efficiency
3. Functional Description x
3.1. TX Datapath 3.2. RX Datapath 3.3. Serial Lite IV Intel® FPGA IP Clock Architecture 3.4. Reset and Link Initialization 3.5. Link Rate and Bandwidth Efficiency Calculation
3.1. TX Datapath x
3.1.1. TX MAC Adapter 3.1.2. Control Word (CW) Insertion 3.1.3. TX CRC 3.1.4. TX MII Encoder 3.1.5. TX PCS and PMA
3.1.2. Control Word (CW) Insertion x
3.1.2.1. Start-of-burst CW 3.1.2.2. End-of-burst CW 3.1.2.3. Alignment Paired CW 3.1.2.4. Empty-cycle CW 3.1.2.5. Idle CW 3.1.2.6. Data Word
3.2. RX Datapath x
3.2.1. RX PCS and PMA 3.2.2. RX MII Decoder 3.2.3. RX CRC 3.2.4. RX Deskew 3.2.5. RX CW Removal
3.4. Reset and Link Initialization x
3.4.1. TX Reset and Initialization Sequence 3.4.2. RX Reset and Initialization Sequence 3.4.3. PMA Adaptation Flow
3.4.3. PMA Adaptation Flow x
3.4.3.1. Starting the PMA Adaptation Flow
4. Getting Started x
4.1. Installing and Licensing Intel® FPGA IP Cores 4.2. Specifying the IP Parameters and Options 4.3. Generated File Structure 4.4. Simulating Intel® FPGA IP Cores 4.5. Synthesizing IP Cores in Other EDA Tools 4.6. Compiling the Full Design
4.1. Installing and Licensing Intel® FPGA IP Cores x
4.1.1. Intel® FPGA IP Evaluation Mode
4.4. Simulating Intel® FPGA IP Cores x
4.4.1. Simulating and Verifying the Design
6. Serial Lite IV Intel® FPGA IP Interface Signals x
6.1. Clock Signals 6.2. Reset Signals 6.3. MAC Signals 6.4. Transceiver Reconfiguration Signals 6.5. PMA Signals
7. Designing with Serial Lite IV Intel® FPGA IP x
7.1. Reset Guidelines 7.2. Error Handling Guidelines 7.3. E-Tile Channel Placement Tool
1. About the Serial Lite IV Intel® FPGA IP User Guide
2. Serial Lite IV Intel® FPGA IP Overview
3. Functional Description
4. Getting Started
5. Parameters
6. Serial Lite IV Intel® FPGA IP Interface Signals
7. Designing with Serial Lite IV Intel® FPGA IP
8. Serial Lite IV Intel® FPGA IP Registers
9. Serial Lite IV Intel® FPGA IP User Guide Archives
10. Document Revision History for the Serial Lite IV Intel® FPGA IP User Guide

3.4.1. TX Reset and Initialization Sequence

The TX reset sequence for Serial Lite IV Intel® FPGA IP is as follows:
  1. Assert tx_pcs_fec_phy_reset_n, tx_core_rst_n, and reconfig_reset simultaneously to reset the custom PCS, MAC, and reconfiguration blocks. Release the custom PCS (tx_pcs_fec_phy_reset_n) and reconfiguration reset (reconfig_reset) after 200 ns to ensure the blocks are properly reset.
  2. The IP then asserts the phy_tx_lanes_stable, tx_pll_locked, and phy_ehip_ready signals after the custom PCS reset is released, to indicate the TX PHY is ready for transmission.
  3. The tx_core_rst_n signal deasserts after phy_ehip_ready signal goes high.
  4. The IP starts transmitting IDLE characters on the MII interface once the MAC is out of reset. There is no requirement for TX lane alignment and skewing because all lanes use the same clock.
  5. While transmitting IDLE characters, the MAC asserts the tx_link_up signal.
  6. The MAC then starts transmitting ALIGN paired with START/END or END/START CWs at a fixed interval to initiate the lane alignment process of the connected receiver.
Figure 23. TX Reset and Initialization Timing Diagram
Level Two Title