Visible to Intel only — GUID: nik1411442129122
Ixiasoft
1. About the CPRI Intel® FPGA IP Core
2. Getting Started with the CPRI Intel® FPGA IP Core
3. Functional Description
4. CPRI Intel® FPGA IP Core Signals
5. CPRI Intel® FPGA IP Core Registers
6. CPRI Intel® FPGA IP User Guide Archives
7. Document Revision History for the CPRI Intel® FPGA IP User Guide
2.1. Installation and Licensing
2.2. Generating CPRI Intel® FPGA IP Core
2.3. CPRI Intel® FPGA IP File Structure
2.4. CPRI Intel® FPGA IP Core Parameters
2.5. Integrating Your Intel® FPGA IP Core in Your Design: Required External Blocks
2.6. Simulating Intel FPGA IP Cores
2.7. Understanding the Testbench
2.8. Running the Design Example
2.9. Compiling the Full Design and Programming the FPGA
2.5.1. Adding the Transceiver TX PLL IP Core
2.5.2. System PLL Connections for the Intel® Agilex™ F-tile Variations
2.5.3. Adding the Reset Controller
2.5.4. Adding the Transceiver Reconfiguration Controller
2.5.5. Adding the Off-Chip Clean-Up PLL
2.5.6. Adding and Connecting the Single-Trip Delay Calibration Blocks
2.5.7. Transceiver PLL Calibration
2.5.8. Reference and System PLL Clock for your IP Design
3.1. Interfaces Overview
3.2. CPRI Intel® FPGA IP Core Clocking Structure
3.3. CPRI Intel® FPGA IP Core Reset Requirements
3.4. Start-Up Sequence Following Reset
3.5. AUX Interface
3.6. Direct IQ Interface
3.7. Ctrl_AxC Interface
3.8. Direct Vendor Specific Access Interface
3.9. Real-Time Vendor Specific Interface
3.10. Direct HDLC Serial Interface
3.11. Direct L1 Control and Status Interface
3.12. L1 Debug Interface
3.13. Media Independent Interface (MII) to External Ethernet Block
3.14. Gigabit Media Independent Interface (GMII) to External Ethernet Block
3.15. CPU Interface to CPRI Intel® FPGA IP Registers
3.16. Auto-Rate Negotiation
3.17. Extended Delay Measurement
3.18. Deterministic Latency and Delay Measurement and Calibration
3.19. CPRI Intel® FPGA IP Transceiver and Transceiver Management Interfaces
3.20. Testing Features
3.19.1. CPRI Link
3.19.2. Main Transceiver Clock and Reset Signals
3.19.3. Arria V, Arria V GZ, Cyclone V, and Stratix V Transceiver Reconfiguration Interface
3.19.4. Intel® Arria® 10, Intel® Stratix® 10, and Intel® Agilex™ Transceiver Reconfiguration Interface
3.19.5. RS-FEC Interface
3.19.6. Interface to the External Reset Controller
3.19.7. Interface to the External PLL
3.19.8. Transceiver Debug Interface
Visible to Intel only — GUID: nik1411442129122
Ixiasoft
2.1. Installation and Licensing
The CPRI Intel® FPGA IP core is an extended FPGA IP core which is not included with the Intel® Quartus® Prime release. This section provides a general overview of the Intel® extended FPGA IP core installation process to help you quickly get started with any Intel® extended FPGA IP core.
The Intel® extended FPGA IP cores are available from the Intel® Self-Service Licensing Center (SSLC). Refer to Related Information below for the correct link for this IP core.
Figure 2. Intel® FPGA IP Core Installation Directory Structure Directory structure after you install the CPRI IP core.
Location | Software | Platform |
---|---|---|
<drive>:\intelFPGA_pro\<version>\quartus\ip\altera_cloud | Intel® Quartus® Prime Pro Edition | Windows* |
<drive>:\intelFPGA\<version>\quartus\ip\altera_cloud | Intel® Quartus® Prime Standard Edition | Windows |
<home directory>:/intelFPGA_pro/<version>/quartus/ip/altera_cloud | Intel® Quartus® Prime Pro Edition | Linux* |
<home directory>:/intelFPGA/<version>/quartus/ip/altera_cloud | Intel® Quartus® Prime Standard Edition | Linux |
Related Information