Multi Channel DMA Intel® FPGA IP for PCI Express Design Example User Guide

Download PDF
ID 683517
Date 8/24/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Introduction 2. Design Example Detailed Description 3. Design Example Quick Start Guide 4. Multi Channel DMA Intel FPGA IP for PCI Express Design Example User Guide Archives 5. Revision History for the Multi Channel DMA Intel FPGA IP for PCI Express Design Example User Guide
1. Introduction x
1.1. Terms and Acronyms 1.2. MCDMA IP Modes
2. Design Example Detailed Description x
2.1. Design Example Overview 2.2. Hardware and Software Requirements 2.3. PIO Using MCDMA Bypass Mode 2.4. Avalon-ST Packet Generate/Check 2.5. Avalon-ST Device-side Packet Loopback 2.6. Avalon-MM DMA 2.7. BAM_BAS Traffic Generator and Checker 2.8. External Descriptor Controller
2.1. Design Example Overview x
2.1.1. MCDMA H-Tile Design Examples for Endpoint 2.1.2. MCDMA P-Tile Design Examples for Endpoint 2.1.3. MCDMA F-Tile Design Examples for Endpoint
2.3. PIO Using MCDMA Bypass Mode x
2.3.1. Avalon-ST PIO Using MCDMA Bypass Mode 2.3.2. Avalon-MM PIO Using MCDMA Bypass mode
2.3.1. Avalon-ST PIO Using MCDMA Bypass Mode x
2.3.1.1. Single-Port Avalon-ST PIO Using MCDMA Bypass Mode
2.3.2. Avalon-MM PIO Using MCDMA Bypass mode x
2.3.2.1. Simulation Results 2.3.2.2. Hardware Test Results
2.4. Avalon-ST Packet Generate/Check x
2.4.1. Single-Port Avalon-ST Packet Generate/Check
2.4.1. Single-Port Avalon-ST Packet Generate/Check x
2.4.1.1. Simulation Waveforms 2.4.1.2. Simulation Log 2.4.1.3. Hardware Test Result
2.5. Avalon-ST Device-side Packet Loopback x
2.5.1. Simulation Results 2.5.2. Hardware Test Results
2.6. Avalon-MM DMA x
2.6.1. Simulation Results 2.6.2. Hardware Test Results
2.7. BAM_BAS Traffic Generator and Checker x
2.7.1. BAM_BAS Traffic Generator and Checker Example Design Register Map
2.8. External Descriptor Controller x
2.8.1. Registers 2.8.2. Hardware Test Results
2.8.1. Registers x
2.8.1.1. GCSR Registers (Base address 64’h00000) 2.8.1.2. QCSR Registers(Base address 64’h10000)
3. Design Example Quick Start Guide x
3.1. Design Example Directory Structure 3.2. Generating the Example Design using Intel® Quartus® Prime 3.3. Simulating the Design Example 3.4. Compiling the Example Design in Intel® Quartus® Prime 3.5. Running the Design Example Application on a Hardware Setup
3.2. Generating the Example Design using Intel® Quartus® Prime x
3.2.1. Procedure
3.3. Simulating the Design Example x
3.3.1. Testbench Overview 3.3.2. Supported Simulators 3.3.3. Example Testbench Flow for DMA Test with Avalon-ST Packet Generate/Check Design Example 3.3.4. Run the Simulation Script 3.3.5. View the Results
3.5. Running the Design Example Application on a Hardware Setup x
3.5.1. Program the FPGA 3.5.2. Quick Start Guide
3.5.2. Quick Start Guide x
3.5.2.1. Software Test Setup 3.5.2.2. Driver Support 3.5.2.3. MCDMA Custom Driver 3.5.2.4. MCDMA DPDK Poll Mode Driver 3.5.2.5. MCDMA Kernel Mode Character Device Driver 3.5.2.6. MCDMA Kernel Mode Network Device Driver
3.5.2.3. MCDMA Custom Driver x
3.5.2.3.1. Prerequisites 3.5.2.3.2. Software Setup 3.5.2.3.3. Run the Reference Example Application 3.5.2.3.4. Testing Bitstream Configuration beyond 256 Channels 3.5.2.3.5. External Descriptor Mode Verification
3.5.2.3.1. Prerequisites x
3.5.2.3.1.1. Configuration Changes from BIOS 3.5.2.3.1.2. External Packages 3.5.2.3.1.3. Set the Boot Parameters
3.5.2.3.2. Software Setup x
3.5.2.3.2.1. Installing the Linux Kernel Driver 3.5.2.3.2.2. Build and Install User Space Library 3.5.2.3.2.3. Enabling VFs and Create Guest VM by Using QEMU 3.5.2.3.2.4. Establish Communication Between Host and QEMU
3.5.2.3.3. Run the Reference Example Application x
3.5.2.3.3.1. Meta Data Test 3.5.2.3.3.2. BAM Test 3.5.2.3.3.3. BAS Test 3.5.2.3.3.4. Packet Gen Test
3.5.2.4. MCDMA DPDK Poll Mode Driver x
3.5.2.4.1. Prerequisites 3.5.2.4.2. Install PMD and Test Application 3.5.2.4.3. Run the Reference Example Application
3.5.2.4.1. Prerequisites x
3.5.2.4.1.1. Set the Boot Parameters 3.5.2.4.1.2. Configuration Changes from BIOS 3.5.2.4.1.3. Install and Build Testpmd
3.5.2.4.2. Install PMD and Test Application x
3.5.2.4.2.1. Create VM Environment
3.5.2.4.3. Run the Reference Example Application x
3.5.2.4.3.1. Example of Verifying on an AVMM Design 3.5.2.4.3.2. BAM Test 3.5.2.4.3.3. BAS Test
3.5.2.5. MCDMA Kernel Mode Character Device Driver x
3.5.2.5.1. Prerequisites 3.5.2.5.2. Software Setup 3.5.2.5.3. Examples
3.5.2.5.1. Prerequisites x
3.5.2.5.1.1. Host Configuration 3.5.2.5.1.2. Set the Boot Parameters
3.5.2.5.2. Software Setup x
3.5.2.5.2.1. Build and Install Kernel Driver 3.5.2.5.2.2. Build and Install Libmcmem 3.5.2.5.2.3. Build Testapp 3.5.2.5.2.4. Configure Kernel Driver 3.5.2.5.2.5. Configure Libmcmem 3.5.2.5.2.6. Configure Testapp
3.5.2.6. MCDMA Kernel Mode Network Device Driver x
3.5.2.6.1. Build and Install Netdev Driver 3.5.2.6.2. Enable VFs if SRIOV is Supported 3.5.2.6.3. Configure the Number of Channels Supported on the Device 3.5.2.6.4. Configure the MTU Value 3.5.2.6.5. Configure the Device Communication 3.5.2.6.6. Configure Transmit Queue Selection Mechanism 3.5.2.6.7. Test Procedure by Using Name Space Environment 3.5.2.6.8. PIO Test
3.5.2.6.6. Configure Transmit Queue Selection Mechanism x
3.5.2.6.6.1. MCDMA Queue Selection 3.5.2.6.6.2. Transmit Packet Steering (XPS) 3.5.2.6.6.3. Default
1. Introduction
2. Design Example Detailed Description
3. Design Example Quick Start Guide
4. Multi Channel DMA Intel FPGA IP for PCI Express Design Example User Guide Archives
5. Revision History for the Multi Channel DMA Intel FPGA IP for PCI Express Design Example User Guide

3.2.1. Procedure

  1. In the Intel® Quartus® Prime Pro Edition software, create a new project File → New Project Wizard.
  2. Specify the Directory, Name, and Top-Level Entity.
  3. For Project Type, accept the default value, Empty project. Click Next.
  4. For Add Files click Next.
  5. For Family, Device & Board Settings, select Intel® Stratix® 10 (GX/SX/MX/TX/DX) or Intel® Agilex™ F-Series or Intel® Agilex™ I-Series and the Target Device for your design.
    Note: The selected device is only used if you select None in Step 10c below.
  6. Click Finish.
  7. In the IP Catalog locate and add the Multi Channel DMA for PCI Express ( Intel® Stratix® 10 GX/MX devices), Multi Channel DMA P-Tile for PCI Express ( Intel® Stratix® 10 DX and Intel® Agilex™ devices), or Multi Channel DMA F-Tile for PCI Express* ( Intel® Agilex™ devices), which brings up the IP Parameter Editor.
  8. In the New IP Variant dialog box, specify a name for your IP. Click Create.
  9. On the IP Settings tabs, specify the parameters for your IP variation.
  10. On the Example Designs tab, make the following selections:
    1. For Example Design Files, turn on the Simulation and Synthesis options. If you do not need these simulation or synthesis files, leaving the corresponding option(s) turned off significantly reduces the example design generation time.
    2. For Generated HDL Format, only Verilog is available in the current release.
    3. For Target Development Kit, select the appropriate option.
      Note: If you select None, the generated design example targets the device specified. Otherwise, the design example uses the device on the selected development board. If you intend to test the design in hardware, make the appropriate pin assignments in the .qsf file.
      Note: No Development Kit is supported for F-Tile in Intel® Quartus® Prime software version 22.3.
    4. For Currently Selected Example Design, select a design example from a pulldown menu. Available design examples depends on the User Mode and Interface type setting in MCDMA Settings under IP Settings tab. Available design examples for the Multi Channel DMA mode and Avalon-ST Interface type:
      • PIO using MQDMA Bypass Mode
      • Packet Generate/Check
      • Device-side Packet Loopback
      Available design examples for the Multi Channel DMA mode and Avalon-MM Interface type:
      • PIO using MQDMA Bypass Mode
      • AVMM DMA
  11. Select Generate Example Design to create a design example that you can simulate and download to hardware. If you target one of the Intel FPGA development kits, the device on that board supersedes the device previously selected in the Intel® Quartus® Prime Pro Edition project if the devices are different. When the prompt asks you to specify the directory for your example design, you can choose to accept the default directory ./intel_pcie_mcdma_0_example_design or choose another directory.
  12. Click Close on Generate Example Design Completed message.
  13. Close the IP Parameter Editor. Click File → Exit. When prompted with Save changes?, you do not need to save the .ip. Click Don’t Save.
Level Two Title