Multi Channel DMA Intel® FPGA IP for PCI Express Design Example User Guide

Download PDF
ID 683517
Date 8/24/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Introduction 2. Design Example Detailed Description 3. Design Example Quick Start Guide 4. Multi Channel DMA Intel FPGA IP for PCI Express Design Example User Guide Archives 5. Revision History for the Multi Channel DMA Intel FPGA IP for PCI Express Design Example User Guide
1. Introduction x
1.1. Terms and Acronyms 1.2. MCDMA IP Modes
2. Design Example Detailed Description x
2.1. Design Example Overview 2.2. Hardware and Software Requirements 2.3. PIO Using MCDMA Bypass Mode 2.4. Avalon-ST Packet Generate/Check 2.5. Avalon-ST Device-side Packet Loopback 2.6. Avalon-MM DMA 2.7. BAM_BAS Traffic Generator and Checker 2.8. External Descriptor Controller
2.1. Design Example Overview x
2.1.1. MCDMA H-Tile Design Examples for Endpoint 2.1.2. MCDMA P-Tile Design Examples for Endpoint 2.1.3. MCDMA F-Tile Design Examples for Endpoint
2.3. PIO Using MCDMA Bypass Mode x
2.3.1. Avalon-ST PIO Using MCDMA Bypass Mode 2.3.2. Avalon-MM PIO Using MCDMA Bypass mode
2.3.1. Avalon-ST PIO Using MCDMA Bypass Mode x
2.3.1.1. Single-Port Avalon-ST PIO Using MCDMA Bypass Mode
2.3.2. Avalon-MM PIO Using MCDMA Bypass mode x
2.3.2.1. Simulation Results 2.3.2.2. Hardware Test Results
2.4. Avalon-ST Packet Generate/Check x
2.4.1. Single-Port Avalon-ST Packet Generate/Check
2.4.1. Single-Port Avalon-ST Packet Generate/Check x
2.4.1.1. Simulation Waveforms 2.4.1.2. Simulation Log 2.4.1.3. Hardware Test Result
2.5. Avalon-ST Device-side Packet Loopback x
2.5.1. Simulation Results 2.5.2. Hardware Test Results
2.6. Avalon-MM DMA x
2.6.1. Simulation Results 2.6.2. Hardware Test Results
2.7. BAM_BAS Traffic Generator and Checker x
2.7.1. BAM_BAS Traffic Generator and Checker Example Design Register Map
2.8. External Descriptor Controller x
2.8.1. Registers 2.8.2. Hardware Test Results
2.8.1. Registers x
2.8.1.1. GCSR Registers (Base address 64’h00000) 2.8.1.2. QCSR Registers(Base address 64’h10000)
3. Design Example Quick Start Guide x
3.1. Design Example Directory Structure 3.2. Generating the Example Design using Intel® Quartus® Prime 3.3. Simulating the Design Example 3.4. Compiling the Example Design in Intel® Quartus® Prime 3.5. Running the Design Example Application on a Hardware Setup
3.2. Generating the Example Design using Intel® Quartus® Prime x
3.2.1. Procedure
3.3. Simulating the Design Example x
3.3.1. Testbench Overview 3.3.2. Supported Simulators 3.3.3. Example Testbench Flow for DMA Test with Avalon-ST Packet Generate/Check Design Example 3.3.4. Run the Simulation Script 3.3.5. View the Results
3.5. Running the Design Example Application on a Hardware Setup x
3.5.1. Program the FPGA 3.5.2. Quick Start Guide
3.5.2. Quick Start Guide x
3.5.2.1. Software Test Setup 3.5.2.2. Driver Support 3.5.2.3. MCDMA Custom Driver 3.5.2.4. MCDMA DPDK Poll Mode Driver 3.5.2.5. MCDMA Kernel Mode Character Device Driver 3.5.2.6. MCDMA Kernel Mode Network Device Driver
3.5.2.3. MCDMA Custom Driver x
3.5.2.3.1. Prerequisites 3.5.2.3.2. Software Setup 3.5.2.3.3. Run the Reference Example Application 3.5.2.3.4. Testing Bitstream Configuration beyond 256 Channels 3.5.2.3.5. External Descriptor Mode Verification
3.5.2.3.1. Prerequisites x
3.5.2.3.1.1. Configuration Changes from BIOS 3.5.2.3.1.2. External Packages 3.5.2.3.1.3. Set the Boot Parameters
3.5.2.3.2. Software Setup x
3.5.2.3.2.1. Installing the Linux Kernel Driver 3.5.2.3.2.2. Build and Install User Space Library 3.5.2.3.2.3. Enabling VFs and Create Guest VM by Using QEMU 3.5.2.3.2.4. Establish Communication Between Host and QEMU
3.5.2.3.3. Run the Reference Example Application x
3.5.2.3.3.1. Meta Data Test 3.5.2.3.3.2. BAM Test 3.5.2.3.3.3. BAS Test 3.5.2.3.3.4. Packet Gen Test
3.5.2.4. MCDMA DPDK Poll Mode Driver x
3.5.2.4.1. Prerequisites 3.5.2.4.2. Install PMD and Test Application 3.5.2.4.3. Run the Reference Example Application
3.5.2.4.1. Prerequisites x
3.5.2.4.1.1. Set the Boot Parameters 3.5.2.4.1.2. Configuration Changes from BIOS 3.5.2.4.1.3. Install and Build Testpmd
3.5.2.4.2. Install PMD and Test Application x
3.5.2.4.2.1. Create VM Environment
3.5.2.4.3. Run the Reference Example Application x
3.5.2.4.3.1. Example of Verifying on an AVMM Design 3.5.2.4.3.2. BAM Test 3.5.2.4.3.3. BAS Test
3.5.2.5. MCDMA Kernel Mode Character Device Driver x
3.5.2.5.1. Prerequisites 3.5.2.5.2. Software Setup 3.5.2.5.3. Examples
3.5.2.5.1. Prerequisites x
3.5.2.5.1.1. Host Configuration 3.5.2.5.1.2. Set the Boot Parameters
3.5.2.5.2. Software Setup x
3.5.2.5.2.1. Build and Install Kernel Driver 3.5.2.5.2.2. Build and Install Libmcmem 3.5.2.5.2.3. Build Testapp 3.5.2.5.2.4. Configure Kernel Driver 3.5.2.5.2.5. Configure Libmcmem 3.5.2.5.2.6. Configure Testapp
3.5.2.6. MCDMA Kernel Mode Network Device Driver x
3.5.2.6.1. Build and Install Netdev Driver 3.5.2.6.2. Enable VFs if SRIOV is Supported 3.5.2.6.3. Configure the Number of Channels Supported on the Device 3.5.2.6.4. Configure the MTU Value 3.5.2.6.5. Configure the Device Communication 3.5.2.6.6. Configure Transmit Queue Selection Mechanism 3.5.2.6.7. Test Procedure by Using Name Space Environment 3.5.2.6.8. PIO Test
3.5.2.6.6. Configure Transmit Queue Selection Mechanism x
3.5.2.6.6.1. MCDMA Queue Selection 3.5.2.6.6.2. Transmit Packet Steering (XPS) 3.5.2.6.6.3. Default
1. Introduction
2. Design Example Detailed Description
3. Design Example Quick Start Guide
4. Multi Channel DMA Intel FPGA IP for PCI Express Design Example User Guide Archives
5. Revision History for the Multi Channel DMA Intel FPGA IP for PCI Express Design Example User Guide

3.5.2.5.3. Examples

  • Testapp options (for Packet Gen/Val): ./testapp –help
  • Pio Test:
    Testapp command: sudo ./testapp --bdf 0000:01:00.0 --piotest
  • BAS Test:
    The BAS support is enabled on the hardware, enable the following flag in: user/common/include/ifc_mcdma.h 
    #define IFC_MCDMA_X16	/* For PCIe x16 */
#define IFC_MCDMA_X8	/* For PCIe x8 */

    Commands:

    To verify the write operation: 
    ./cli/testapp/testapp --bdf 0000:01:00.0\
 --reqsize 1048576 --bas --transmit
    To verify the read operation: 
    ./cli/testapp/testapp --bdf 0000:01:00.0\
 --reqsize 1048576 --bas --receive
    To verify the bi-direction operation: 
    ./cli/testapp/testapp --bdf 0000:01:00.0\
 --reqsize 1048576 --bas --bidirection
    Performance test: 
    ./cli/testapp/testapp --bdf 0000:01:00.0\
 --reqsize 1048576 --basperf --bidirection
  • For more example commands, check the software/user/cli/testapp/README.txt file.
Note: Reset the IP before starting the DMA by using the following command: 
echo 1 > /sys/bus/pci/devices/\
<b:d:f>/mcdma_ipreset
Note:
  1. Please change following macros in cli/testapp/testapp.h 
    #define IFC_MCDMA_BAS_X16 _SHIFT_WIDTH 3 
#define IFC_MCDMA_BAS_X8 _SHIFT_WIDTH 3
  2. By default, testapp tries to configure and enable BAS on BAR2. In case if there is a change of BAR needed, please change the resource file name in testapp.

if you want to change to BAR0, change resource name in path snprintf(path, PATH_MAX, "/sys/bus/pci/devices/%s/resource0", bdf);

Level Two Title