50G Interlaken Intel® FPGA IP User Guide

Download PDF
ID 683217
Date 10/31/2022
Public
Document Table of Contents
Document Table of Contents x
1. About This IP Core 2. Getting Started With the 50G Interlaken IP Core 3. 50G Interlaken IP Core Parameter Settings 4. Functional Description 5. 50G Interlaken IP core Signals 6. 50G Interlaken IP Core Register Map 7. 50G Interlaken IP Core Test Features 8. Advanced Parameter Settings 9. Out-of-Band Flow Control in the 50G Interlaken IP core 10. 50G Interlaken Intel® FPGA IP User Guide Archives 11. Document Revision History for 50G Interlaken Intel® FPGA IP User Guide A. Performance and Fmax Requirements for 40G Ethernet Traffic
1. About This IP Core x
1.1. Features 1.2. Device Family Support 1.3. IP Core Verification 1.4. Performance and Resource Utilization 1.5. Device Speed Grade Support 1.6. Release Information
1.1. Features x
1.1.1. IP Core Supported Combinations of Number of Lanes and Data Rate 1.1.2. IP Core Raw Aggregate Bandwidth
2. Getting Started With the 50G Interlaken IP Core x
2.1. Installing and Licensing Intel® FPGA IP Cores 2.2. Specifying the 50G Interlaken IP Core Parameters and Options 2.3. Files Generated for Arria V GZ and Stratix V Variations 2.4. Files Generated for Intel® Arria® 10 Variations 2.5. Simulating the 50G Interlaken IP Core 2.6. Integrating Your IP Core in Your Design 2.7. Compiling the Full Design and Programming the FPGA 2.8. Creating a Signal Tap Debug File to Match Your Design Hierarchy
2.1. Installing and Licensing Intel® FPGA IP Cores x
2.1.1. Intel® FPGA IP Evaluation Mode
2.6. Integrating Your IP Core in Your Design x
2.6.1. Pin Assignments 2.6.2. Transceiver Logical Channel Numbering 2.6.3. Adding the Reconfiguration Controller 2.6.4. Adding the External PLL
2.6.3. Adding the Reconfiguration Controller x
2.6.3.1. Generating the Reconfiguration Controller 2.6.3.2. Connecting the Reconfiguration Controller to the IP Core
3. 50G Interlaken IP Core Parameter Settings x
3.1. Meta Frame Length in Words 3.2. Enable Native PHY Debug Master Endpoint (NPDME) 3.3. Transceiver Reference Clock Frequency 3.4. Number of Calendar Pages 3.5. TX Scrambler Seed 3.6. Transfer Mode Selection
4. Functional Description x
4.1. Interfaces Overview 4.2. High Level Block Diagram 4.3. Clocking and Reset Structure for IP Core 4.4. Interleaved and Packet Modes 4.5. 50G Interlaken IP Core Transmit Path 4.6. 50G Interlaken IP Core Receive Path
4.1. Interfaces Overview x
4.1.1. Application Interface 4.1.2. Interlaken Interface 4.1.3. Out‑of‑Band Flow Control Interface 4.1.4. Management Interface 4.1.5. Transceiver Control Interfaces
4.1.5. Transceiver Control Interfaces x
4.1.5.1. Transceiver Reconfiguration Controller Interface 4.1.5.2. Intel® Arria® 10 External PLL Interface 4.1.5.3. Intel® Arria® 10 Transceiver Reconfiguration Interface
4.3. Clocking and Reset Structure for IP Core x
4.3.1. 50G Interlaken IP Core Clock Signals 4.3.2. IP Core Reset 4.3.3. IP Core Reset Sequence with the Reconfiguration Controller
4.5. 50G Interlaken IP Core Transmit Path x
4.5.1. 50G Interlaken IP Core Transmit User Data Interface Examples 4.5.2. 50G Interlaken IP Core In-Band Calendar Bits on Transmit Side 4.5.3. 50G Interlaken IP Core Transmit Path Blocks
4.5.1. 50G Interlaken IP Core Transmit User Data Interface Examples x
4.5.1.1. 50G Interlaken IP Core Interleaved Mode (Segmented Mode) Example 4.5.1.2. 50G Interlaken IP Core Packet Mode Operation Example 4.5.1.3. 50G Interlaken IP Core Back-Pressured Packet Transfer Example
4.5.3. 50G Interlaken IP Core Transmit Path Blocks x
4.5.3.1. 50G Interlaken IP Core TX Transmit Buffer 4.5.3.2. 50G Interlaken IP Core TX MAC 4.5.3.3. 50G Interlaken IP Core TX PCS 4.5.3.4. 50G Interlaken IP Core TX PMA
4.6. 50G Interlaken IP Core Receive Path x
4.6.1. 50G Interlaken IP Core Receive User Data Interface Examples 4.6.2. 50G Interlaken IP Core RX Errored Packet Handling 4.6.3. In-Band Calendar Bits on the 50G Interlaken IP Core Receiver User Data Interface 4.6.4. 50G Interlaken IP Core Receive Path Blocks
4.6.1. 50G Interlaken IP Core Receive User Data Interface Examples x
4.6.1.1. 50G Interlaken IP Core Receiver Side Example
4.6.2. 50G Interlaken IP Core RX Errored Packet Handling x
4.6.2.1. 50G Interlaken IP Core Receiver Side Example With Errors and In-Band Calendar Bits
4.6.4. 50G Interlaken IP Core Receive Path Blocks x
4.6.4.1. 50G Interlaken IP Core RX PMA 4.6.4.2. 50G Interlaken IP Core RX PCS 4.6.4.3. 50G Interlaken IP Core RX MAC 4.6.4.4. 50G Interlaken IP Core RX Regroup Block
5. 50G Interlaken IP core Signals x
5.1. 50G Interlaken IP Core Clock Interface Signals 5.2. 50G Interlaken IP Core Reset Interface Signals 5.3. 50G Interlaken IP Core User Data Transfer Interface Signals 5.4. 50G Interlaken IP Core Interlaken Link and Miscellaneous Interface Signals 5.5. 50G Interlaken IP Core Management Interface 5.6. Device Dependent Signals
5.6. Device Dependent Signals x
5.6.1. Transceiver Reconfiguration Controller Interface Signals 5.6.2. Intel® Arria® 10 External PLL Interface Signals 5.6.3. Intel® Arria® 10 Transceiver Reconfiguration Interface Signals
7. 50G Interlaken IP Core Test Features x
7.1. Internal Serial Loopback Mode 7.2. External Loopback Mode 7.3. PRBS Generation and Validation 7.4. CRC32 Error Injection
7.3. PRBS Generation and Validation x
7.3.1. Setting up PRBS Mode in Arria V and Stratix V Devices 7.3.2. Setting up PRBS Mode in Intel® Arria® 10 Devices
8. Advanced Parameter Settings x
8.1. Hidden Parameters 8.2. Modifying Hidden Parameter Values
8.1. Hidden Parameters x
8.1.1. Required User Clock Frequency 8.1.2. Counter Reset Bits 8.1.3. Include Temp Sense 8.1.4. RXFIFO Address Width 8.1.5. SWAP_TX_LANES and SWAP_RX_LANES (Data Word Lane Swapping) 8.1.6. Use ATX or CMU PLL 8.1.7. Lane Profile
9. Out-of-Band Flow Control in the 50G Interlaken IP core x
9.1. Out-of-Band Flow Control Block Clocks 9.2. TX Out‑of‑Band Flow Control Signals 9.3. RX Out-of-Band Flow Control Signals
1. About This IP Core
2. Getting Started With the 50G Interlaken IP Core
3. 50G Interlaken IP Core Parameter Settings
4. Functional Description
5. 50G Interlaken IP core Signals
6. 50G Interlaken IP Core Register Map
7. 50G Interlaken IP Core Test Features
8. Advanced Parameter Settings
9. Out-of-Band Flow Control in the 50G Interlaken IP core
10. 50G Interlaken Intel® FPGA IP User Guide Archives
11. Document Revision History for 50G Interlaken Intel® FPGA IP User Guide
A. Performance and Fmax Requirements for 40G Ethernet Traffic

9.3. RX Out-of-Band Flow Control Signals

The receive out-of-band flow control interface receives input flow‑control clock, data, and sync signals and sends out calendar and status information. The RX Out-of-Band Flow Control Interface Signals table describes the receive out‑of‑band flow control interface signals specified in the Interlaken Protocol Specification, Revision 1.2. The RX Out-of-Band Flow Control Block Signals for Application Use describes the signals on the application side of the RX out‑of‑band flow control block.

Table 27.  RX Out-of-Band Flow Control Interface Signals

Signal Name

Direction

Width (Bits)

Description

fc_clk

Input

1

Input reference clock from an upstream out-of-band TX block. This signal clocks the fc_data and fc_sync signals. You must connect this signal to a device pin.

fc_data

Input

1

Input serial data pin from an upstream out-of-band TX block. You must connect this signal to a device pin.

fc_sync

Input

1

Input sync control pin from an upstream out-of-band TX block. You must connect this signal to a device pin.

Table 28.  RX Out-of-Band Flow Control Block Signals for Application Use

Signal Name

Direction

Width (Bits)

Description

sys_clk

Input

1

Reference clock for capturing RX calendar, lane status, and link status. Frequency must be at least double the frequency of the TX fc_clk input clock.

sys_arst

Input

1

Asynchronous reset for the out-of-band RX block.

status_update

Output

1

Indicates a new value without CRC4 errors is present on at least one of lane_status or link_status in the current sys_clk cycle. The value is ready to be read by the application logic.

lane_status

Output

Number of Lanes

Lane status bits received from an upstream out-of-band TX block on fc_data. Width is the number of lanes.

link_status

Output

1

Link status bit received from an upstream out-of-band TX block on fc_data.

status_error

Output

1

Indicates corrupt lane or link status. A new value is present on at least one of lane_status or link_status in the current sys_clk cycle, but the value has at least one CRC4 error.

calendar

Output

16

Calendar bits received from an upstream out-of-band TX block on fc_data.

calendar_update

Output

1

Indicates a new value without CRC4 errors is present on calendar in the current sys_clk cycle. The value is ready to be read by the application logic.

calendar_error

Output

1

Indicates corrupt calendar bits. A new value is present calendar in the current sys_clk cycle, but the value has at least one CRC4 error.

Related Information
Level Two Title