Quartus® Prime Pro Edition User Guide: Design Constraints

Download PDF
ID 683143
Date 8/07/2024
Public
Document Table of Contents
Document Table of Contents x
Answers to Top FAQs 1. Constraining Designs 2. Interface Planning 3. Managing Device I/O Pins 4. Quartus® Prime Pro Edition User Guide: Design Constraints Document Archives A. Quartus® Prime Pro Edition User Guides
1. Constraining Designs x
1.1. Specifying Design Constraints in the GUI 1.2. Constraining Designs with Tcl Scripts 1.3. A Fully Iterative Scripted Flow 1.4. Constraining Designs Revision History
1.1. Specifying Design Constraints in the GUI x
1.1.1. Global Constraints and Assignments 1.1.2. Node, Entity, and Instance-Level Constraints 1.1.3. Probing Between Components of the Quartus® Prime GUI 1.1.4. Specifying Timing Constraints
1.1.2. Node, Entity, and Instance-Level Constraints x
1.1.2.1. Specify Instance-Specific Constraints in Assignment Editor 1.1.2.2. Specify NoC Constraints in NoC Assignment Editor 1.1.2.3. Specify Dual Simplex Assignments in DS Assignment Editor 1.1.2.4. Specify I/O Constraints in Pin Planner 1.1.2.5. Plan Interface Constraints in Interface Planner and Tile Interface Planner 1.1.2.6. Adjust Constraints with the Chip Planner 1.1.2.7. Constraining Designs with the Design Partition Planner
1.1.2.1. Specify Instance-Specific Constraints in Assignment Editor x
1.1.2.1.1. Specifying Multi-Dimensional Bus Constraints
1.1.2.2. Specify NoC Constraints in NoC Assignment Editor x
1.1.2.2.1. NoC Assignment Editor Interface Controls 1.1.2.2.2. Troubleshooting NoC Assignment Editor
1.2. Constraining Designs with Tcl Scripts x
1.2.1. Create a Project and Apply Constraints 1.2.2. Assigning a Pin 1.2.3. Generating Quartus® Prime Settings Files Organized .qsf File 1.2.4. Synopsys* Design Constraint (.sdc) Files 1.2.5. Tcl-only Script Flows
2. Interface Planning x
2.1. Using Interface Planner 2.2. Using Tile Interface Planner 2.3. Interface Planning Revision History
2.1. Using Interface Planner x
2.1.1. Interface Planner User Interface 2.1.2. Interface Planner General Tool Flow 2.1.3. Interface Planner NoC Tool Flow 2.1.4. Interface Planner Reports
2.1.1. Interface Planner User Interface x
2.1.1.1. Flow Controls 2.1.1.2. Home Tab Controls 2.1.1.3. Assignments Tab Controls 2.1.1.4. Plan Tab Controls 2.1.1.5. Reports Tab Controls
2.1.2. Interface Planner General Tool Flow x
2.1.2.1. Step 1: Setup and Synthesize the Project 2.1.2.2. Step 2: Initialize Interface Planner 2.1.2.3. Step 3: Update Plan with Project Assignments 2.1.2.4. Step 4: Plan Periphery Placement 2.1.2.5. Step 5: Report Placement Data 2.1.2.6. Step 6: Validate and Export Plan Constraints
2.1.2.4. Step 4: Plan Periphery Placement x
2.1.2.4.1. Plan Clock Networks 2.1.2.4.2. Saving & Loading Floorplans
2.1.4. Interface Planner Reports x
2.1.4.1. Report Summary 2.1.4.2. Report Pins 2.1.4.3. Report HSSI Channels 2.1.4.4. Report Clocks 2.1.4.5. Report Periphery Locations 2.1.4.6. Report Cell Connectivity 2.1.4.7. Report Instance Assignments 2.1.4.8. Report NoC Performance
2.2. Using Tile Interface Planner x
2.2.1. Tile Interface Planner Terminology 2.2.2. Tile Interface Planner Tool Flow 2.2.3. Constraining Dynamic Reconfiguration IP 2.2.4. Tile Interface Planner GUI Reference
2.2.2. Tile Interface Planner Tool Flow x
2.2.2.1. Step 1: Instantiate IP and Run Design Analysis 2.2.2.2. Step 2: Initialize Tile Interface Planner 2.2.2.3. Step 3: Update Plan with Project Assignments 2.2.2.4. Step 4: Create a Tile Plan 2.2.2.5. Step 5: Save Tile Plan Assignments 2.2.2.6. Step 6: Run Logic Generation and Design Synthesis
2.2.2.4. Step 4: Create a Tile Plan x
2.2.2.4.1. Placing IP Components 2.2.2.4.2. Constraining IP Building Blocks
2.2.3. Constraining Dynamic Reconfiguration IP x
2.2.3.1. Defining a Dynamic Reconfiguration Group 2.2.3.2. Assigning Dynamic Reconfiguration Group Placement
2.2.4. Tile Interface Planner GUI Reference x
2.2.4.1. Flow Controls 2.2.4.2. Home Tab 2.2.4.3. Assignments Tab Controls 2.2.4.4. Plan Tab Controls 2.2.4.5. Tcl Console Window
2.2.4.4. Plan Tab Controls x
2.2.4.4.1. Design Tree and Filters 2.2.4.4.2. Reconfiguration Groups View 2.2.4.4.3. Legal Locations Pane
3. Managing Device I/O Pins x
3.1. I/O Planning Overview 3.2. Assigning I/O Pins 3.3. Importing and Exporting I/O Pin Assignments 3.4. Validating Pin Assignments 3.5. Verifying I/O Timing 3.6. Viewing Routing and Timing Delays 3.7. Scripting API 3.8. Managing Device I/O Pins Revision History
3.1. I/O Planning Overview x
3.1.1. Basic I/O Planning Flow 3.1.2. Integrating PCB Design Tools 3.1.3. Intel FPGA Device and I/O Terminology
3.2. Assigning I/O Pins x
3.2.1. Assigning to Exclusive Pin Groups 3.2.2. Assigning Slew Rate and Drive Strength 3.2.3. Assigning I/O Banks 3.2.4. Changing Pin Planner Highlight Colors 3.2.5. Showing I/O Lanes 3.2.6. Assigning Differential Pins 3.2.7. Entering Pin Assignments with Tcl Commands 3.2.8. Entering Pin Assignments in HDL Code
3.2.6. Assigning Differential Pins x
3.2.6.1. Overriding I/O Placement Rules on Differential Pins
3.2.8. Entering Pin Assignments in HDL Code x
3.2.8.1. Using Low-Level I/O Primitives
3.3. Importing and Exporting I/O Pin Assignments x
3.3.1. Importing and Exporting for PCB Tools 3.3.2. Migrating Assignments to Another Target Device
3.4. Validating Pin Assignments x
3.4.1. I/O Assignment Validation Rules 3.4.2. I/O Assignment Analysis 3.4.3. Understanding I/O Analysis Reports
3.4.2. I/O Assignment Analysis x
3.4.2.1. Early I/O Assignment Analysis Without Design Files 3.4.2.2. I/O Assignment Analysis With Design Files 3.4.2.3. Overriding Default I/O Pin Analysis
3.5. Verifying I/O Timing x
3.5.1. Running Advanced I/O Timing 3.5.2. Adjusting I/O Timing and Power with Capacitive Loading
3.5.1. Running Advanced I/O Timing x
3.5.1.1. Board Trace Models 3.5.1.2. Defining the Board Trace Model 3.5.1.3. Modifying the Board Trace Model 3.5.1.4. Specifying Near-End vs Far-End I/O Timing Analysis 3.5.1.5. Advanced I/O Timing Analysis Reports
3.7. Scripting API x
3.7.1. Generate Mapped Netlist 3.7.2. Reserve Pins 3.7.3. Set Location 3.7.4. Exclusive I/O Group 3.7.5. Slew Rate and Current Strength
Answers to Top FAQs
1. Constraining Designs
2. Interface Planning
3. Managing Device I/O Pins
4. Quartus® Prime Pro Edition User Guide: Design Constraints Document Archives
A. Quartus® Prime Pro Edition User Guides

1.2.3. Generating Quartus® Prime Settings Files

Quartus® Prime software allows you to generate .qsf files from your revision. You can embed these constraints in a scripted compilation flow, and even create sets of .qsf files for design optimization.

To generate a .qsf file from the Quartus® Prime software, click Assignments > Export Assignments.

To organize the .qsf in a human readable form, Project > Organize Quartus® Prime Settings File.

Organized .qsf File

This example shows how .qsf files characterize a design revision. The set_global_assignment command makes all global constraints and software settings and set_location_assignment constrains each I/O node in the design to a physical pin on the device. 

# Project-Wide Assignments
# ========================
set_global_assignment -name SYSTEMVERILOG_FILE top.sv
set_global_assignment -name SYSTEMVERILOG_FILE blinking_led.sv
set_global_assignment -name SDC_FILE blinking_led.sdc
set_global_assignment -name SDC_FILE jtag.sdc
set_global_assignment -name PROJECT_OUTPUT_DIRECTORY output_files
set_global_assignment -name LAST_QUARTUS_VERSION "17.1.0 Pro Edition"
set_global_assignment -name TEXT_FILE blinking_led_generated.txt
# Pin & Location Assignments
# ==========================
set_location_assignment PIN_AN18 -to clock
set_location_assignment PIN_AR23 -to led_zero_on
set_location_assignment PIN_AM21 -to led_two_on
set_location_assignment PIN_AR22 -to led_one_on
set_location_assignment PIN_AL20 -to led_three_on
# Analysis & Synthesis Assignments
# ================================
set_global_assignment -name FAMILY "Arria 10"
set_global_assignment -name TOP_LEVEL_ENTITY top
# Fitter Assignments
# ==================
set_global_assignment -name DEVICE 10AS066N3F40E2SG
# -----------------
# start ENTITY(top)
# Fitter Assignments
# ==================
set_instance_assignment -name IO_STANDARD "1.8 V" -to led_zero_on
set_instance_assignment -name IO_STANDARD "1.8 V" -to led_one_on
set_instance_assignment -name IO_STANDARD "1.8 V" -to led_two_on
set_instance_assignment -name IO_STANDARD "1.8 V" -to led_three_on
set_instance_assignment -name SLEW_RATE 1 -to led_zero_on
set_instance_assignment -name SLEW_RATE 1 -to led_one_on
set_instance_assignment -name SLEW_RATE 1 -to led_two_on
set_instance_assignment -name SLEW_RATE 1 -to led_three_on
set_instance_assignment -name CURRENT_STRENGTH_NEW 12MA -to clock
set_instance_assignment -name CURRENT_STRENGTH_NEW 12MA -to led_zero_on
set_instance_assignment -name CURRENT_STRENGTH_NEW 12MA -to led_one_on
set_instance_assignment -name CURRENT_STRENGTH_NEW 12MA -to led_two_on
set_instance_assignment -name CURRENT_STRENGTH_NEW 12MA -to led_three_on
# end ENTITY(top)
# ---------------
Related Information
Level Two Title