GPIO Intel® FPGA IP User Guide: Intel® Arria® 10 and Intel® Cyclone® 10 GX Devices

Download PDF
ID 683136
Date 9/13/2023
Public
Document Table of Contents
Document Table of Contents x
GPIO Intel® FPGA IP User Guide: Intel® Arria® 10 and Intel® Cyclone® 10 GX Devices
GPIO Intel® FPGA IP User Guide: Intel® Arria® 10 and Intel® Cyclone® 10 GX Devices x
Release Information for GPIO Intel® FPGA IP GPIO Intel® FPGA IP Features GPIO Intel® FPGA IP Data Paths GPIO Intel® FPGA IP Interface Signals Verifying Resource Utilization and Design Performance GPIO Intel® FPGA IP Parameter Settings Register Packing GPIO Intel® FPGA IP Timing GPIO Intel® FPGA IP Design Examples IP Migration Flow for Arria® V, Cyclone® V, and Stratix® V Devices Intel® Arria® 10 and Intel® Cyclone® 10 GX GPIO Intel® FPGA IP User Guide Archives Document Revision History for GPIO Intel® FPGA IP User Guide: Intel® Arria® 10 and Intel® Cyclone® 10 GX Devices
GPIO Intel® FPGA IP Data Paths x
Input Path Output and Output Enable Paths
GPIO Intel® FPGA IP Interface Signals x
Shared Signals Data Bit-Order for Data Interface Input and Output Bus High and Low Bits Data Interface Signals and Corresponding Clocks
GPIO Intel® FPGA IP Timing x
Timing Components Delay Elements Timing Analysis Timing Closure Guidelines
Timing Analysis x
Single Data Rate Input Register Full-Rate or Half-Rate DDIO Input Register Single Data Rate Output Register Full-Rate or Half-Rate DDIO Output Register
GPIO Intel® FPGA IP Design Examples x
GPIO Intel® FPGA IP Synthesizable Intel® Quartus® Prime Design Example GPIO Intel® FPGA IP Simulation Design Example
IP Migration Flow for Arria® V, Cyclone® V, and Stratix® V Devices x
Migrating Your ALTDDIO_IN, ALTDDIO_OUT, ALTDDIO_BIDIR, and ALTIOBUF IP Cores Guideline: Swap datain_h and datain_l Ports in Migrated IP
GPIO Intel® FPGA IP User Guide: Intel® Arria® 10 and Intel® Cyclone® 10 GX Devices

GPIO Intel® FPGA IP Interface Signals

Depending on the parameter settings you specify, different interface signals are available for the GPIO IP.
Figure 7.  GPIO IP Interfaces


Figure 8.  GPIO Interface Signals


Table 3.  Pad Interface SignalsThe pad interface is the physical connection from the GPIO IP to the pad. This interface can be an input, output or bidirectional interface, depending on the IP configuration. In this table, SIZE is the data width specified in the IP parameter editor.
Signal Name Direction Description
pad_in[SIZE-1:0] Input

Input signal from the pad.
pad_in_b[SIZE-1:0] Input

Negative node of the differential input signal from the pad. This port is available if you turn on the Use differential buffer option.

pad_out[SIZE-1:0] Output Output signal to the pad.
pad_out_b[SIZE-1:0] Output

Negative node of the differential output signal to the pad. This port is available if you turn on the Use differential buffer option.

pad_io[SIZE-1:0] Bidirectional

Bidirectional signal connection with the pad.
pad_io_b[SIZE-1:0] Bidirectional

Negative node of the differential bidirectional signal connection with the pad. This port is available if you turn on the Use differential buffer option.

Table 4.  Data Interface SignalsThe data interface is an input or output interface from the GPIO IP to the FPGA core. In this table, SIZE is the data width specified in the IP parameter editor.
Signal Name Direction Description
din[DATA_SIZE-1:0] Input

Data input from the FPGA core in output or bidirectional mode. DATA_SIZE depends on the register mode:

  • Bypass or simple register— DATA_SIZE = SIZE
  • DDIO without half-rate logic— DATA_SIZE = 2 × SIZE
  • DDIO with half-rate logic— DATA_SIZE = 4 × SIZE
dout[DATA_SIZE-1:0] Output

Data output to the FPGA core in input or bidirectional mode, DATA_SIZE depends on the register mode:

  • Bypass or simple register— DATA_SIZE = SIZE
  • DDIO without half-rate logic— DATA_SIZE = 2 × SIZE
  • DDIO with half-rate logic— DATA_SIZE = 4 × SIZE
oe[OE_SIZE-1:0] Input

OE input from the FPGA core in output mode with Enable output enable port turned on, or bidirectional mode. OE is active high. When transmitting data, set this signal to 1. When receiving data, set this signal to 0. OE_SIZE depends on the register mode:

  • Bypass or simple register— DATA_SIZE = SIZE
  • DDIO without half-rate logic— DATA_SIZE = SIZE
  • DDIO with half-rate logic— DATA_SIZE = 2 × SIZE
Table 5.  Clock Interface SignalsThe clock interface is an input clock interface. It consists of different signals, depending on the configuration. The GPIO IP can have zero, one, two, or four clock inputs. Clock ports appear differently in different configurations to reflect the actual function performed by the clock signal.
Signal Name Direction Description
ck Input

In input and output paths, this clock feeds a packed register or DDIO if you turn off the Half Rate logic parameter.

In bidirectional mode, this clock is the unique clock for the input and output paths if you turn off the Separate input/output Clocks parameter.

ck_fr Input

In input and output paths, these clocks feed the full-rate and half-rate DDIOs if your turn on the Half Rate logic parameter.

In bidirectional mode, the input and output paths use these clocks if you turn off the Separate input/output Clocks parameter.

ck_hr
ck_in Input

In bidirectional mode, these clocks feed a packed register or DDIO in the input and output paths if you specify both these settings:

  • Turn off the Half Rate logic parameter.
  • Turn on the Separate input/output Clocks parameter.
ck_out
ck_fr_in Input

In bidirectional mode, these clocks feed a full-rate and half-rate DDIOs in the input and output paths if you specify both of these settings:

  • Turn on the Half Rate logic parameter.
  • Turn on the Separate input/output Clocks parameter.

For example, ck_fr_out feeds the full-rate DDIO in the output path.

ck_fr_out
ck_hr_in
ck_hr_out
cke Input Clock enable.
Table 6.  Termination Interface SignalsThe termination interface connects the GPIO IP to the I/O buffers.
Signal Name Direction Description
seriesterminationcontrol Input Input from the termination control block (OCT) to the buffers. It sets the buffer series impedance value.
parallelterminationcontrol Input Input from the termination control block (OCT) to the buffers. It sets the buffer parallel impedance value.
Table 7.  Reset Interface SignalsThe reset interface connects the GPIO IP core to the DDIOs.
Signal Name Direction Description
sclr Input

Synchronous clear input. Not available if you select None or Preset for the Enable synchronous clear / preset port option.

aclr Input

Asynchronous clear input. Active high. Not available if you select None or Preset for the Enable asynchronous clear / preset port option.

aset Input

Asynchronous set input. Active high. Not available if you select None or Clear for the Enable asynchronous clear / preset port option.

sset Input Synchronous set input. Not available if you select None or Clear for the Enable synchronous clear / preset port option.

Section Content
Shared Signals
Data Bit-Order for Data Interface
Input and Output Bus High and Low Bits
Data Interface Signals and Corresponding Clocks

Related Information
Level Two Title