F-Tile Serial Lite IV Intel® FPGA IP User Guide

Download PDF
ID 683074
Date 10/08/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the F-Tile Serial Lite IV Intel® FPGA IP User Guide 2. F-Tile Serial Lite IV Intel® FPGA IP Overview 3. Getting Started 4. Functional Description 5. Parameters 6. F-Tile Serial Lite IV Intel® FPGA IP Interface Signals 7. Control and Status Registers 8. Designing with F-Tile Serial Lite IV Intel® FPGA IP 9. F-Tile Serial Lite IV Intel® FPGA IP User Guide Archives 10. Document Revision History for the F-Tile Serial Lite IV Intel® FPGA IP User Guide
2. F-Tile Serial Lite IV Intel® FPGA IP Overview x
2.1. Release Information 2.2. Supported Features 2.3. IP Version Support Level 2.4. Device Speed Grade Support 2.5. Resource Utilization and Latency 2.6. Bandwidth Efficiency
3. Getting Started x
3.1. Installing and Licensing Intel® FPGA IP Cores 3.2. Specifying the IP Parameters and Options 3.3. Generated File Structure 3.4. Simulating Intel® FPGA IP Cores 3.5. Synthesizing IP Cores in Other EDA Tools 3.6. Compiling the Full Design
3.1. Installing and Licensing Intel® FPGA IP Cores x
3.1.1. Intel® FPGA IP Evaluation Mode
3.4. Simulating Intel® FPGA IP Cores x
3.4.1. Simulating and Verifying the Design
4. Functional Description x
4.1. TX Datapath 4.2. RX Datapath 4.3. F-Tile Serial Lite IV Intel® FPGA IP Clock Architecture 4.4. Reset and Link Initialization 4.5. Link Rate and Bandwidth Efficiency Calculation 4.6. 32-bit Soft CWBIN Counters 4.7. i_stats_snapshot Port 4.8. Deterministic Latency
4.1. TX Datapath x
4.1.1. TX MAC Adapter 4.1.2. Control Word (CW) Insertion 4.1.3. TX CRC 4.1.4. TX MII Encoder 4.1.5. TX PCS and PMA
4.1.2. Control Word (CW) Insertion x
4.1.2.1. Start-of-burst CW 4.1.2.2. End-of-burst CW 4.1.2.3. Alignment Paired CW 4.1.2.4. Empty-cycle CW 4.1.2.5. Idle CW 4.1.2.6. Data Word
4.2. RX Datapath x
4.2.1. RX PCS and PMA 4.2.2. RX MII Decoder 4.2.3. RX CRC 4.2.4. RX Deskew 4.2.5. RX CW Removal
4.4. Reset and Link Initialization x
4.4.1. TX Reset and Initialization Sequence 4.4.2. RX Reset and Initialization Sequence
6. F-Tile Serial Lite IV Intel® FPGA IP Interface Signals x
6.1. Clock Signals 6.2. Reset Signals 6.3. MAC Signals 6.4. Transceiver Reconfiguration Signals 6.5. PMA Signals
7. Control and Status Registers x
7.1. F-Tile Serial Lite IV Intel® FPGA IP Soft CSR
8. Designing with F-Tile Serial Lite IV Intel® FPGA IP x
8.1. Reset Guidelines 8.2. Error Handling Guidelines 8.3. Analog Parameter Settings
1. About the F-Tile Serial Lite IV Intel® FPGA IP User Guide
2. F-Tile Serial Lite IV Intel® FPGA IP Overview
3. Getting Started
4. Functional Description
5. Parameters
6. F-Tile Serial Lite IV Intel® FPGA IP Interface Signals
7. Control and Status Registers
8. Designing with F-Tile Serial Lite IV Intel® FPGA IP
9. F-Tile Serial Lite IV Intel® FPGA IP User Guide Archives
10. Document Revision History for the F-Tile Serial Lite IV Intel® FPGA IP User Guide

3.3. Generated File Structure

The Quartus® Prime Pro Edition software generates the following IP output file structure.

For information about the file structure of the design example, refer to the F-Tile Serial Lite IV Intel® FPGA IP Design Example User Guide.

Figure 4.  F-Tile Serial Lite IV Intel® FPGA IP Generated Files
Table 8.   F-Tile Serial Lite IV Intel® FPGA IP Generated Files

File Name

Description

<your_ip>.ip

The Platform Designer system or top-level IP variation file. <your_ip> is the name that you give your IP variation.

<your_ip>.cmp The VHDL Component Declaration (.cmp) file is a text file that contains local generic and port definitions that you can use in VHDL design files.
<your_ip>.html

A report that contains connection information, a memory map showing the address of each slave with respect to each master to which it is connected, and parameter assignments.

<your_ip>_generation.rpt IP or Platform Designer generation log file. A summary of the messages during IP generation.
<your_ip>.qgsimc Lists simulation parameters to support incremental regeneration.
<your_ip>.qgsynthc Lists synthesis parameters to support incremental regeneration.
<your_ip>.qip

Contains all the required information about the IP component to integrate and compile the IP component in the Quartus® Prime software.

<your_ip>.sopcinfo

Describes the connections and IP component parameterizations in your Platform Designer system. You can parse its contents to get requirements when you develop software drivers for IP components.

Downstream tools such as the Nios® II tool chain use this file. The .sopcinfo file and the system.h file generated for the Nios® II tool chain include address map information for each slave relative to each master that accesses the slave. Different masters may have a different address map to access a particular slave component.

<your_ip>.csv Contains information about the upgrade status of the IP component.
<your_ip>.spd

Required input file for ip-make-simscript to generate simulation scripts for supported simulators. The .spd file contains a list of files generated for simulation, along with information about memories that you can initialize.

<your_ip>_bb.v You can use the Verilog black-box (_bb.v) file as an empty module declaration for use as a black box.
<your_ip>_inst.v or _inst.vhd HDL example instantiation template. You can copy and paste the contents of this file into your HDL file to instantiate the IP variation.
<your_ip>.regmap If IP contains register information, .regmap file generates. The .regmap file describes the register map information of master and slave interfaces. This file complements the .sopcinfo file by providing more detailed register information about the system. This enables register display views and user customizable statistics in the System Console.
<your_ip>.svd

Allows hard processor system (HPS) System Debug tools to view the register maps of peripherals connected to HPS in a Platform Designer system.

During synthesis, the .svd files for slave interfaces visible to System Console masters are stored in the .sof file in the debug section. System Console reads this section, which Platform Designer can query for register map information. For system slaves, Platform Designer can access the registers by name.

<your_ip>.v or <your_ip>.vhd HDL files that instantiate each submodule or child IP for synthesis or simulation.
mentor/

Contains a ModelSim* / QuestaSim* script msim_setup.tcl to set up and run a simulation.

synopsys/vcs/

synopsys/vcsmx/

Contains a shell script vcs_setup.sh to set up and run a VCS* simulation.

Contains a shell script vcsmx_setup.sh and synopsys_sim.setup file to set up and run a VCS* MX simulation.

xcelium/

Contains a shell script xcelium_setup.sh and other setup files to set up and run Xcelium* simulation.

submodules/ Contains HDL files for the IP submodules.
<child IPs>/ For each generated child IP directory, Platform Designer generates synth/ and sim/ sub-directories.
Level Two Title