F-Tile Serial Lite IV Intel® FPGA IP User Guide

Download PDF
ID 683074
Date 10/08/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the F-Tile Serial Lite IV Intel® FPGA IP User Guide 2. F-Tile Serial Lite IV Intel® FPGA IP Overview 3. Getting Started 4. Functional Description 5. Parameters 6. F-Tile Serial Lite IV Intel® FPGA IP Interface Signals 7. Control and Status Registers 8. Designing with F-Tile Serial Lite IV Intel® FPGA IP 9. F-Tile Serial Lite IV Intel® FPGA IP User Guide Archives 10. Document Revision History for the F-Tile Serial Lite IV Intel® FPGA IP User Guide
2. F-Tile Serial Lite IV Intel® FPGA IP Overview x
2.1. Release Information 2.2. Supported Features 2.3. IP Version Support Level 2.4. Device Speed Grade Support 2.5. Resource Utilization and Latency 2.6. Bandwidth Efficiency
3. Getting Started x
3.1. Installing and Licensing Intel® FPGA IP Cores 3.2. Specifying the IP Parameters and Options 3.3. Generated File Structure 3.4. Simulating Intel® FPGA IP Cores 3.5. Synthesizing IP Cores in Other EDA Tools 3.6. Compiling the Full Design
3.1. Installing and Licensing Intel® FPGA IP Cores x
3.1.1. Intel® FPGA IP Evaluation Mode
3.4. Simulating Intel® FPGA IP Cores x
3.4.1. Simulating and Verifying the Design
4. Functional Description x
4.1. TX Datapath 4.2. RX Datapath 4.3. F-Tile Serial Lite IV Intel® FPGA IP Clock Architecture 4.4. Reset and Link Initialization 4.5. Link Rate and Bandwidth Efficiency Calculation 4.6. 32-bit Soft CWBIN Counters 4.7. i_stats_snapshot Port 4.8. Deterministic Latency
4.1. TX Datapath x
4.1.1. TX MAC Adapter 4.1.2. Control Word (CW) Insertion 4.1.3. TX CRC 4.1.4. TX MII Encoder 4.1.5. TX PCS and PMA
4.1.2. Control Word (CW) Insertion x
4.1.2.1. Start-of-burst CW 4.1.2.2. End-of-burst CW 4.1.2.3. Alignment Paired CW 4.1.2.4. Empty-cycle CW 4.1.2.5. Idle CW 4.1.2.6. Data Word
4.2. RX Datapath x
4.2.1. RX PCS and PMA 4.2.2. RX MII Decoder 4.2.3. RX CRC 4.2.4. RX Deskew 4.2.5. RX CW Removal
4.4. Reset and Link Initialization x
4.4.1. TX Reset and Initialization Sequence 4.4.2. RX Reset and Initialization Sequence
6. F-Tile Serial Lite IV Intel® FPGA IP Interface Signals x
6.1. Clock Signals 6.2. Reset Signals 6.3. MAC Signals 6.4. Transceiver Reconfiguration Signals 6.5. PMA Signals
7. Control and Status Registers x
7.1. F-Tile Serial Lite IV Intel® FPGA IP Soft CSR
8. Designing with F-Tile Serial Lite IV Intel® FPGA IP x
8.1. Reset Guidelines 8.2. Error Handling Guidelines 8.3. Analog Parameter Settings
1. About the F-Tile Serial Lite IV Intel® FPGA IP User Guide
2. F-Tile Serial Lite IV Intel® FPGA IP Overview
3. Getting Started
4. Functional Description
5. Parameters
6. F-Tile Serial Lite IV Intel® FPGA IP Interface Signals
7. Control and Status Registers
8. Designing with F-Tile Serial Lite IV Intel® FPGA IP
9. F-Tile Serial Lite IV Intel® FPGA IP User Guide Archives
10. Document Revision History for the F-Tile Serial Lite IV Intel® FPGA IP User Guide

4.8. Deterministic Latency

To support real-time data, ensure that there is no drop of real-time samples during the insertion of CW or de-assertion of tx_avs_ready required to create bandwidth for FEC_ALIGN_MARKER insertion. Only BASIC mode which supports continuous streaming of data will be used in this real-time data transfer whereas FULL mode is not supported in the Deterministic Latency (DL) use case.

Real-time samples are required to be buffered when the F-Tile Serial Lite IV Intel® FPGA IP is not ready to transmit and to allow the samples to be transferred to the receiver when F-Tile Serial Lite IV Intel® FPGA IP is ready. The bandwidth should be higher to account for the F-Tile Serial Lite IV protocol overhead. Similarly, on the receiver side, you need to buffer enough samples to avoid any gap during transfer when the F-Tile Serial Lite IV Intel® FPGA IP tx_avs_ready would create holes in the real time samples being written in the RX buffer.

Refer to the F-Tile Serial Lite IV Intel® FPGA IP Design Example User Guide for more details regarding how to use the DL feature.

Level Two Title