GTS Ethernet Intel® FPGA Hard IP User Guide

Download PDF
ID 817676
Date 7/08/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Install and License the GTS Ethernet Intel® FPGA Hard IP 3. Configure and Generate Ethernet Hard IP variant 4. Integrate GTS Ethernet Intel® FPGA Hard IP into Your Application 5. Simulate, Compile, and Validate (MAC+PCS) - Single Instance 6. Simulate, Compile, and Validate (MII PCS Only /PCS66 OTN/PCS66 FlexE) - Single Instance 7. Simulate, Compile, and Validate SyncE - Single Instance 8. Simulate and Compile PTP1588 - Single Instance 9. Simulate, Compile, and Validate - Multiple Instance 10. Troubleshoot and Diagnose Issues A. Appendix A: Functional Description B. Appendix B: Configuration Registers C. Appendix C: Document Revision History for the GTS Ethernet Intel® FPGA Hard IP User Guide
1. Overview x
1.1. Release Information 1.2. High-Level Functional Overview 1.3. Acronyms 1.4. Agilex™ 5 Ethernet Portfolio and Target Applications 1.5. Agilex™ 5 Ethernet Hard IP Features 1.6. GTS Ethernet Intel® FPGA Hard IP Design Flow
1.5. Agilex™ 5 Ethernet Hard IP Features x
1.5.1. Device Family Support 1.5.2. Device Speed Grade Support 1.5.3. Resource Utilization
3. Configure and Generate Ethernet Hard IP variant x
3.1. Create Quartus Project 3.2. Configure GTS Ethernet Hard IP 3.3. Generate HDL for Synthesis and Simulation 3.4. Generated File Structure 3.5. Generate GTS EHIP Design Example 3.6. Analog Parameter Options
3.5. Generate GTS EHIP Design Example x
3.5.1. Directory Structure
4. Integrate GTS Ethernet Intel® FPGA Hard IP into Your Application x
4.1. Implement Required Clocking 4.2. Implement Required Resets 4.3. Connect the Status Interface 4.4. Connect the MAC Avalon Streaming Client Interface 4.5. Connect the MII PCS Only Client Interface 4.6. Connect the PCS66 Client Interface – FlexE and OTN 4.7. Connect the Precision Time Protocol Interface 4.8. Connect the Ethernet Hard IP Reconfiguration Interface
4.1. Implement Required Clocking x
4.1.1. Implement MAC Synchronous Clock Connections to Single Instance 4.1.2. Implement MAC Synchronous Clock Connections to Multiple Instances 4.1.3. Implement Clock Connections to MAC Asynchronous Operation 4.1.4. Implement Clock Connections in Synchronous Ethernet Operation (Sync-E) 4.1.5. Implement Clock Connections in PTP-Based Design
4.2. Implement Required Resets x
4.2.1. Reset Sequence 4.2.2. Connect the GTS Reset Sequencer Intel® FPGA IP
4.2.2. Connect the GTS Reset Sequencer Intel® FPGA IP x
4.2.2.1. Requirements and Considerations for GTS Reset Sequencer Intel® FPGA IP
4.3. Connect the Status Interface x
4.3.1. Use i_stats_snapshot to Read Stats Counters
4.4. Connect the MAC Avalon Streaming Client Interface x
4.4.1. Connect the TX MAC Avalon Streaming Client Interface 4.4.2. Connect the RX MAC Avalon Streaming Client Interface 4.4.3. Connect the MAC Flow Control Interface
4.4.1. Connect the TX MAC Avalon Streaming Client Interface x
4.4.1.1. Drive the Ethernet Packet to the TX MAC Avalon Streaming Client Interface with Disabled Preamble Passthrough 4.4.1.2. Drive the Ethernet Packet on the TX MAC Avalon Streaming Client Interface with Enabled Preamble Passthrough 4.4.1.3. Use i_tx_skip_crc to Control Source Address, PAD, and CRC Insertion 4.4.1.4. Assert the i_tx_error to Invalidate a Packet
4.4.2. Connect the RX MAC Avalon Streaming Client Interface x
4.4.2.1. Receive Ethernet Frame on the RX MAC Avalon Streaming Client Interface with Preamble Passthrough Disabled 4.4.2.2. Receive Ethernet Frame with Preamble Passthrough Enabled 4.4.2.3. Receive Ethernet Frame with Remove CRC bytes Disabled 4.4.2.4. Monitor Status and Errors on the RX MAC Avalon Streaming Client Interface
4.4.3. Connect the MAC Flow Control Interface x
4.4.3.1. Connect the TX MAC Flow Control Interface 4.4.3.2. Connect the RX MAC Flow Control Interface
4.5. Connect the MII PCS Only Client Interface x
4.5.1. Connect the MII PCS Mode TX Interface 4.5.2. Connect the MII PCS Mode RX Interface
4.5.1. Connect the MII PCS Mode TX Interface x
4.5.1.1. Insert Alignment Marker
4.5.2. Connect the MII PCS Mode RX Interface x
4.5.2.1. Receive Alignment Marker
4.6. Connect the PCS66 Client Interface – FlexE and OTN x
4.6.1. Connect the FlexE and OTN Mode TX Interface 4.6.2. Connect the FlexE and OTN Mode RX Interface
4.6.1. Connect the FlexE and OTN Mode TX Interface x
4.6.1.1. Insert Alignment Marker
4.6.2. Connect the FlexE and OTN Mode RX Interface x
4.6.2.1. Receive Alignment Marker
4.7. Connect the Precision Time Protocol Interface x
4.7.1. Connect the Time-of-Day Interface 4.7.2. Connect the TX Two-Step Timestamp Interface 4.7.3. Connect the TX One-Step Timestamp Interface 4.7.4. Connect the RX Timestamp Interface 4.7.5. Connect the PTP Status Interface
4.7.3. Connect the TX One-Step Timestamp Interface x
4.7.3.1. PTP Field Offset for 1-Step Operation
5. Simulate, Compile, and Validate (MAC+PCS) - Single Instance x
5.1. Design Example Features 5.2. Design Example Components 5.3. Simulate the Design Example 5.4. Compile the Design Example in Hardware 5.5. Validate the Design Example in Hardware
5.3. Simulate the Design Example x
5.3.1. Simulation Testbench Flow 5.3.2. Verify the Simulation Results
5.5. Validate the Design Example in Hardware x
5.5.1. Configure the Clocks in Hardware 5.5.2. Program the FPGA 5.5.3. Run the Hardware Test
6. Simulate, Compile, and Validate (MII PCS Only /PCS66 OTN/PCS66 FlexE) - Single Instance x
6.1. Design Example Features 6.2. Design Example Components 6.3. Simulate the Design Example 6.4. Compile the Design Example in Hardware 6.5. Validate the Design Example in Hardware
6.3. Simulate the Design Example x
6.3.1. Simulation Testbench Flow 6.3.2. Simulators Output
6.5. Validate the Design Example in Hardware x
6.5.1. Configure the Clocks in Hardware 6.5.2. Program the FPGA 6.5.3. Run the Hardware Test
7. Simulate, Compile, and Validate SyncE - Single Instance x
7.1. Design Example Features 7.2. Design Example Components 7.3. Simulate the Design Example 7.4. Compile the Design Example in Hardware 7.5. Validate the Design Example in Hardware
7.3. Simulate the Design Example x
7.3.1. Simulation Testbench Flow for Single Instance with SyncE 7.3.2. Simulator Output
7.5. Validate the Design Example in Hardware x
7.5.1. Configure the Clocks in Hardware 7.5.2. Program the FPGA 7.5.3. Run the Hardware Test
8. Simulate and Compile PTP1588 - Single Instance x
8.1. Design Example Features 8.2. Design Example Components 8.3. Simulate the Design Example 8.4. Compile the Design Example in Hardware
8.3. Simulate the Design Example x
8.3.1. Simulation Testbench Flow 8.3.2. Simulator Output
9. Simulate, Compile, and Validate - Multiple Instance x
9.1. Design Example Features 9.2. Design Example Components 9.3. Simulate the Design Example 9.4. Compile the Design Example in Hardware 9.5. Validate the Design Example in Hardware
9.3. Simulate the Design Example x
9.3.1. Simulation Testbench Flow for MAC Mode 9.3.2. Simulator Output
9.5. Validate the Design Example in Hardware x
9.5.1. Configure the Clocks in Hardware 9.5.2. Program the FPGA 9.5.3. Run the Hardware Test
10. Troubleshoot and Diagnose Issues x
10.1. Enable Diagnostic Lookback Modes 10.2. Troubleshoot the Reset Sequence 10.3. Use Signal Tap Analyzer for Troubleshooting
10.1. Enable Diagnostic Lookback Modes x
10.1.1. Internal Serial Loopback 10.1.2. Enable MAC Loopback 10.1.3. Enable PCS Loopback 10.1.4. Enable External Loopback 10.1.5. Packet Client Loopback
10.2. Troubleshoot the Reset Sequence x
10.2.1. Debug the Power Up Reset Sequence 10.2.2. Debug the TX Reset Entry Sequence 10.2.3. Debug the TX Reset Exit Sequence 10.2.4. Debug the RX Reset Entry Sequence 10.2.5. Debug the RX Reset Exit Sequence 10.2.6. Debug the Auto Recovery Reset Sequence
A. Appendix A: Functional Description x
A.1. Datapath Description A.2. GTS Ethernet Intel® FPGA Hard IP MAC A.3. PCS, OTN, and FlexE Modes A.4. Precision Time Protocol Interface
A.2. GTS Ethernet Intel® FPGA Hard IP MAC x
A.2.1. MAC TX Datapath A.2.2. MAC RX Datapath A.2.3. Congestion and Flow Control Using PAUSE or Priority Flow Control (PFC) A.2.4. Link Fault Signaling A.2.5. Order of Ethernet Transmission:
A.2.1. MAC TX Datapath x
A.2.1.1. Insert TX Preamble, Start, and SFD A.2.1.2. Insert Source Address A.2.1.3. Process Length/Type Field A.2.1.4. Pad the Client Frame A.2.1.5. Insert Frame Check Sequence (CRC-32) A.2.1.6. Generate and Insert Inter-Packet Gap
A.2.2. MAC RX Datapath x
A.2.2.1. Process RX Preamble A.2.2.2. Check RX Strict SFD A.2.2.3. Check RX FCS A.2.2.4. Handle RX Malformed Packet A.2.2.5. Remove PAD Bytes and FCS Bytes from RX Frames A.2.2.6. RX Undersized Frames, Oversized Frames, and Frames with Length Errors A.2.2.7. Inter-Packet Gap
A.2.3. Congestion and Flow Control Using PAUSE or Priority Flow Control (PFC) x
A.2.3.1. Conditions Triggering XOFF Frame Transmission A.2.3.2. Conditions Triggering XON Frame Transmission A.2.3.3. Pause Control and Generation Interface A.2.3.4. Pause Control Frame Filtering
A.3. PCS, OTN, and FlexE Modes x
A.3.1. PCS Mode A.3.2. OTN Mode A.3.3. FlexE Mode
A.4. Precision Time Protocol Interface x
A.4.1. Features A.4.2. PTP User Flow A.4.3. Make PTP UI Adjustments A.4.4. Reference Time Interval A.4.5. Minimum and Maximum Reference Time (TAM) Interval for UI Measurement (Hardware)
A.4.2. PTP User Flow x
A.4.2.1. PTP TX User Flow A.4.2.2. PTP RX User Flow
A.4.3. Make PTP UI Adjustments x
A.4.3.1. Adjust TX UI A.4.3.2. Adjust RX UI
B. Appendix B: Configuration Registers x
B.1. Ethernet Avalon® Memory-Mapped Interface Address Space B.2. Packet Client Registers
1. Overview
2. Install and License the GTS Ethernet Intel® FPGA Hard IP
3. Configure and Generate Ethernet Hard IP variant
4. Integrate GTS Ethernet Intel® FPGA Hard IP into Your Application
5. Simulate, Compile, and Validate (MAC+PCS) - Single Instance
6. Simulate, Compile, and Validate (MII PCS Only /PCS66 OTN/PCS66 FlexE) - Single Instance
7. Simulate, Compile, and Validate SyncE - Single Instance
8. Simulate and Compile PTP1588 - Single Instance
9. Simulate, Compile, and Validate - Multiple Instance
10. Troubleshoot and Diagnose Issues
A. Appendix A: Functional Description
B. Appendix B: Configuration Registers
C. Appendix C: Document Revision History for the GTS Ethernet Intel® FPGA Hard IP User Guide

4.7.2. Connect the TX Two-Step Timestamp Interface

The timestamp interface signals are valid when i_tx_valid and i_tx_startofpacket signals are high. To initiate a timestamp request, the i_ptp_ts_req signal must be high. You must also specify a fingerprint value in the i_ptp_fp signal.

The diagram below depicts the transmission of two packets. The first packet contains a two-step timestamp request with an assigned fingerprint, FP1.

Figure 48. IEEE 1588 TX Two-Step Timestamp Interface
  • The timestamp signals are only valid when i_tx_valid and i_tx_startofpacket are both high.
  • i_ptp_ts_req must be high to initiate a timestamp request.
  • The request must be accompanied by a fingerprint value on the i_ptp_fp port.
Note: The fingerprint values can be re-used when the timestamp for the packet is returned.
The diagram below depicts how a timestamp is returned for a packet when a 2-step timestamp request is issued:
Figure 49. Two-Step Timestamp: Receiving Timestamp for a Fingerprint
  • o_ptp_ets_valid is asserted to indicate that o_ptp_ets and o_ptp_ets_fp have a valid timestamp information.
  • o_ptp_ets is the timestamp, and o_ptp_ets_fp is the fingerprint (identifier) of the packet for which the timestamp is for.
Table 41.  Two-Step TX Timestamp Interface SignalsThe timestamp is always in 1588 v2 format.
Signal Name Width Description
i_ptp_ts_req[0:0] 1

Request a 2-step timestamp for the current TX packet

1: Generate a TX timestamp for the current packet

TX MAC SOP-Aligned Client Interface:

i_ptp_ts_req[0] is valid only when i_tx_valid = 1 and i_tx_startofpacket = 1

i_ptp_fp[<w>-1:0]

<w> = Timestamp fingerprint width selected in GUI option

 </w>

Fingerprint for current TX Packet

This bus is used to assign an 8 bit “fingerprint” to a TX packet that is being transmitted, so that the TX egress timestamp associated with the TX packet can be identified – the timestamp will be returned with the same fingerprint.

TX MAC SOP-Aligned Client Interface:

i_ptp_fp[<w>-1:0] is valid only when i_tx_valid = 1 and i_tx_startofpacket = 1

Used for both 2-step and 1-step PTP packets.

Intel recommends using a large range of fingerprints, to avoid the possibility of assigning the same fingerprint to 2 TX packets that are being processed.

o_ptp_ets_valid[0:0] 1

TX Egress Timestamp Valid

1: The fingerprint and egress timestamp ports are presenting valid output on this cycle.
o_ptp_ets[95:0] 96

TX Egress Timestamp

This bus is used to present an egress timestamp for the TX Packet that was transmitted with the fingerprint given by o_ptp_ets_fp

o_ptp_ets[95:0] is valid only when o_ptp_ets_valid[0] = 1

Used to present TX egress timestamps for both 2-step and 1-step PTP packets.

The timestamp is in 1588v2 format (96b).

The timestamp is for the packet whose fingerprint matches the fingerprint with the egress timestamp.

The timestamp indicates the estimated time at which the first bit of the start-of-packet block for the TX packet is transmitted from the tx_serial pin.

All timestamps are referenced to the copy of the Time-of-Day maintained on the EHIP.

o_ptp_ets_fp[<w>-1:0]

<w> = Timestamp fingerprint width selected in GUI option

 <w>

TX Egress Timestamp Fingerprint

This bus presents the fingerprint for the current 2-step egress timestamp. The fingerprint can be used to determine which TX Packet the timestamp belongs with.

o_ptp_ets_fp[<w>-1:0] is valid only when o_ptp_ets_valid[0] = 1

Used to present TX egress timestamps fingerprints for both 2-step and 1-step PTP packets.
Level Two Title